Global Specialties 1315D User Manual

1315D
0-25V/5A, AC/DC
POWER SUPPLY
Instruction Manual
M-00458 EDITION : 1 ( JULY, 2012 )
GLGL
OBOB
GL
GLGL
Global Specialties,LLC
22820 Savi Ranch Parkway Yorba linda,CA 92887 WWW.globalspecialties.com
OB
AL SPECIAL
OBOB
TIESTIES
TIES
TIESTIES
&
Know your Power Supply read the Manual prior to Operation.
TABLE OF CONTENTS
SECTION PARTICULARS PAGE NO.
1 GENERAL INFORMATION 1
2 INSTALLATION 2
3 OPERATING INSTRUCTIONS 3
4 PART LIST 4
CAUTION NOTE
!
This power supply has been designed and tested in accordance with the safety requirements for electrical equipment for measurement,control and laboratory use. This manual contains important information and warnings which have to be followed by the user for his safety as well as safe operation of the unit. This power supply operates according to safety Class 'I' Standards.
SECTION - 1
GENERAL INFORMATION
DESCRIPTION :
This simple AC/DC power source is designed specifically for use in educational institutions. It can be used to demon­strate the concept of alternating and non-alternating volt­ages. It can also be used for simple experiments using lamps, resistances, etc. The unit has been provided with Voltmeter and Ammeter for AC / DC Voltage and current
readings
SPECIFICATIONS :
AC Voltage :
PCB Components Z-DPM/02 ======================================================================= Ref Designator Value ======================================================================= IC
IC1 ICL7107 CPL VR1 TL431
FND
DS1 GREEN FND COMMON ANODE DS2 GREEN FND COMMON ANODE DS3 GREEN FND COMMON ANODE
CONNECTORS
J1 3PIN, 2.54MM MALE J3 4PIN, 2.54MM MALE R4 12H555 SPADE CONNECTOR.
Output voltage No Load : 0V to 30V (nom) Full Load : 0V to 25V ±2V
Output current : 5A max Output protection : 5A Circuit Breaker
DC Voltage :
No Load : 0V to 40V Full Load : 0V to 25V ± 2V
Output voltage : 0V to 25V (nom) Output current : 5A max Output protection : 6A Circuit Breaker DPM V/A Selection : 2Pole/2Way Push Sw. Output Voltage : 3 Digit LED Display (Green) Output Current : 3 Digit LED Display (Green)
General :
Input power : 115V / 230VAC,60 Hz,single phase Input Fuse 115/230V : 2A /3A, 250V Slow Blow Dimensions : 235mm x 155mm x 295 mm.
( W x H x D ) approx.
Weight : 10.0 Kg. approx.
GENERAL ======================================================================= Ref Designator Value ======================================================================= SWITCHES
SW1 ON / OFF SWITCH
6A, 125V, DPST, ILLUMINATED
SW2 2P2T 5A POWER SWITCH.
DIODE BRIDGE 10A / 600V
VARISTOR 20D 361 ( 230V ).
20D Z131 ( 115V )
DIMMER INPUT 2A / 115V AC
OUTPUT 5A / 30V, AC
CIRCUIT BREAKER 5A / 125V AC
6A / 125V DC
FUSE HOLDER FHB/02 10A/250V.
INPUT FUSE 2A / 250V, SLOW BLOW
TERMINAL BTI-15N RED 12A x 1
BTI-15N BLACK 12A x 1 BTI-15N BLUE 12A x 2
TRANSFORMERS CURRENT TRANSFORMERS
DPM TRANSFORMERS
SPARE CARBON
1
6
PCB Components Z 2505/AC-(SPL) 0205 ======================================================================= Ref Designator Value ======================================================================= CAPACITORS
C1 1µF, 50V, ELE C2 1µF, 50V, ELE C3 0.1µF, 50V, CD C4 47µF, 50V, ELE C4* 0.1µF, 50V, CD C5 10µF, 50V, ELE C6 470µF, 30V, ELE C7 10µF, 50V, ELE C8 0.1µF, 50V, CD C9 0.1µF, 50V, CD C10 220µF, 30V, ELE C10* 0.1µF, 50V, CD C11 10µF, 50V, ELE C12 0.1µF, 50V, CD
ICs
U1 UA7805 U2 UA7812 U3 UA7905
SECTION - 2
INSTALLATION
INITIAL INSPECTION :
As soon as the 1315D variable AC/DC source is unpacked, inspect for any damages that may have occured during transit. Save all packing material until inspection is complete. If damage is found, notify the carriers immediately. Our authorised representative also should be notified.
PHYSICAL CHECK :
This check should confirm that there are no broken knobs. The cabinet and panel surfaces should be free of dents.
ELECTRICAL CHECK :
PCB Components Z-DPM/02 ======================================================================= Ref Designator Value ======================================================================= RESISTORS
R1 39K, ¼W, 5% MFR R2 470E, ¼W, 5% MFR R3 1MEG, ¼W, 5% MFR R5 10K, ¼W, 5% MFR R6 2.4K, ¼W, 5% MFR R7 330E, ¼W, 5% MFR R9 120K, ¼W, 5% MFR
PRESETS
PR1 2.5K / 3K ( HOR )
CAPACITORS
C1 220pF, 50V, CD C3 0.01µF, 50V, CD C4 0.47µF, 50V, MP C5 0.1µF, 50V, MP C6 0.1µF, 50V, MP C7 10µF, 50V, ELE C7* 0.1µF, 50V, MP C8 0.1µF, 50V, CD C9 10µF, 50V, ELE C10 0.1µF, 50V, CD
5
The 1315D variable AC/DC source is shipped ready for bench operation. It is necessary only to connect the instrument to a rated input voltage 115V or 230VAC / 60 Hz / 5A source of power. To select the correct input voltage select tap selection switch at the rear panel and it is ready for operation.
INPUT POWER REQUIREMENTS :
The 1315D variable AC/DC source may be operated continuously from a 115V or 230V AC / 60 Hz power sourc with the help of input selector switch at the rear panel.
REPACKING FOR SHIPMENT :
To ensure safe shipment of the 1315D variable AC/DC source, it is recommended that the package designed for the instrument be used. The original packing material is reusable.
2
SECTION - 3
OPERATING INSTRUCTIONS
SECTION - 4
PART LIST
a) 1315D as AC supply :
Set output voltage to 0V by turning the variable control to minimum position ( Anti Clockwise ). Set Power ON switch to apply input power. Adjust the voltage control to obtain the required output voltage. The variable control is a coarse control to adjust the output voltage with in 0-30V Connect the load at the AC output. The output voltage will be 25V after connecting 5A Load. The total load current should not exceed 5A for continuous operation. In case of sustained overload, the overload trip operates to isolate the power supply from the load. When the overload is removed, the trip switch can be reset.
b) 1315D as DC supply :
Set output voltage to 0V by turning the variable control to minimum position ( Anti Clockwise ).
Set Power ON switch to apply input power. Adjust the voltage control to obtain the required output voltage at the Red & Black Terminals. The variable control is a coarse control to adjust the output voltage with in 0-40V. Connect the load at the DC output terminals. The output waveform is full­wave rectified DC output. The output voltage will be 25V approx after connecting 5A Load. The total load current should not exceed 5 A for continuous operation.
In case of sustained overload, the overload trip operates to isolate the power supply from the load. When the overload is removed, the trip switch can be reset.
c) Panel Meter :3 Digit DPM will read voltage & current of AC/DC outputs by selecting the Push Switch on the front panel to monitor respective Voltage & Current.
d) Indications :
Power ON will be indicated by illuminated ON/OFF Switch.
PCB Components Z 2505/AC-(SPL) 0205 ======================================================================= Ref Designator Value =======================================================================
RESISTORS
R1 30K, ¼W, 5% MFR R2 200E, ¼W, 5% MFR R3 150E, ¼W, 5% MFR R4 220E, ¼W, 5% MFR R5 30E, ¼W, 5% MFR R6 240E, ¼W, 5% MFR R7 20E, ¼W, 5% MFR R7* 680E, ¼W, 5% MFR R8 100E, ¼W, 5% MFR R9 100E, 2W, 5% MFR
DIODES
D1 1N4007 D2 1N4007
BRIDGE
BR1 1A / 100V, CSB-1 BR2 1A / 100V, CSB-1 BR3 1A / 100V, CSB-1 BR4 1A / 100V, CSB-1
RELAYS
RLY1 58-12-2C 2P/2W 12V RELAY RLY2 58-12-2C 2P/2W 12V RELAY
PRESETS
VR1 100E VR2 100E VR3 100E VR4 100E
CONNECTORS
J1 3PIN, 2.54MM MALE J3 2PIN, 2.54MM MALE J4 4PIN, 2.54MM MALE J5 8PIN, 2.54MM MALE J6 3PIN, 2.54MM MALE J7 3PIN, 2.54MM MALE R7 12H555 SPADE CONNECTOR.
3 4
Loading...