1.
4.
OK/
u
Power On/O
(hold 3 sec.)
or Backlight
4.
OK/Setup or
Pa
Pause (in training)
2.
Page Down
GB-1000 User Manual
3.
Page Up
v2.0
Q1. How to start training and check your training data?
[Power On]
3 sec.
* AVERAGE SPEED TOTAL ACCUMULATED DISTANCE * TRIP DISTANCE
* MAXIMUM SPEED CALORIES
** MAXIMUM CADENCE ** AVERAGE CADENCE
[OK]
The satellite icon will flash while locating.
current timeof day
** CURRENT CADENCE
TRIP TIME
BLUE arrow means [Page Up]
RED arrow means [Page Down]
* If speed/cadence combo sensor is not connected, speed and distance will be calculated by GPS.
** only when speed/cadence combo sensor is connected
Q2. How to configure and pair your device?
Please enter configuration
mode at START page.
[Page Down] or [Page Up] to
adjust height
[OK]
[Page Down] or [Page Up] to
adjust age
[OK]
3 sec.
[OK]
[OK]
[Page Down] / [Page Up]
[Page Down] or [Page Up] to
select language
[Page Down] or [Page Up] to
adjust weight
[Page Down] or [Page Up] to
switchtime mode
[OK]
[OK]
[OK]
[Page Down] or [Page Up] to
swap unit system.
[Page Down] or [Page Up] to
selectgender
[Page Down] or [Page Up]
to adjust time zone
[OK]
[Page Down] or [Page Up] to adjust
wheel size
Metric: mm
English: inch
[OK]
[OK]
[OK]
Speed/Cadence
combo sensor
pairing process
[OK]
Speed/Cadence icon will flash while
pairingSpeed/Cadence sensor.
Speed/Cadence
combo sensor pairing
success?
No
Yes
[OK]
When turning on, device will discover and connect previous paired
Speed/Cadence automatically.
[OK]
Go back
to START
page
Q3. How to use GO-TO function?
A3 Step 1: Save Waypoint
You cannot save one waypoint
[Page Down]
if GO-TO function is in use.
3 sec.
No
waypoint can only be saved when GPS is located
GPS fixed ?
Yes
save waypoint?
[OK]
[Page Down] /
[Page Up]
skip waypoint saving?
[OK]
You can save only “one” waypoint on this device and previous waypoint will be replaced by
new waypoint.
A3 Step 2: Guide to Waypoint (GO-TO function)
[Page Up]
3 sec.
Yes
Go-To
in use?
No Yes
No
Waypoint
exists?
[OK]
cancel Go-To
[Page Down] /
[Page Up]
[Page Down] /
[Page Up]
[OK]
return to Go-To mode
activate GO-TO function
[OK]
Q3.1. What does GO-TO function mean?
A3.1: GO-TO function can guide you to the saved waypoint by pointing the direction.
When you are close enough to the saved waypoint (within 20 m), device will show
“GOAL ARRIVED ”.
exit Go-To
[OK]
Q4. How to do total distance reset and factory reset?
[Page Down]
& [Page Up]
3 sec.
[OK/Setup] to
re-confirm
Total Distance
Reset
[OK/Setup] to
cancel reset
action and
go back
Start page
You can only reset
at start page.
[Page Down] and go
back to Total
Distance Reset
TOTAL DISTANCE RESET?
[Page Down]
TOTAL DISTANCE SET?
[Page Down]
FACTORY RESET?
[Page Down]
[OK/Setup]to
re-confirm
Total Distance
Set
[Page Down] / [Page Up]
[OK/Setup]
to do Total
DistanceSet
[OK/Setup]to
re-confirm Factory Reset
[Page Down] / [Page Up]
[Page Down] / [Page Up]
[OK/Setup]
to reset
Total Distance
to zero
[OK/Setup] to
cancel set
action and
go back
Start page
[Page Down] /
[Page Up] to
adjust Total
Distance
[OK/Setup]
to set
TotalDistance
[OK/Setup] to
cancel reset
action and
go back
Start page
Press
“OK/Setup”
to do
Factory Reset
[OK/Setup]to exit and go
back to Start page
Q4.1. What does total distance reset mean?
A4.1: “TOTAL DISTANCE RESET” will reset the total accumulated distance to zero.
Q4.2. What dose factory reset mean?
A4.2: “FACTORY RESET” will reset all settings to original factory values.
Q5. How to reboot the device?
A5: Hold [Power On/Off] for 8 seconds to do hardware shutdown and then turn on again to
reboot the device.
Q6. Other questions
Q6.1. How to pause during your training?
A6.1: Just press [OK/Setup] when you are in training and current training status
will be held. When system is pausing, the upper speed area will show “
P” and you can still check current training status by pressing [Page Down]
/ [Page Up].
Q6.2. How to save training data?
A6.2: Training data will be saved while turning off the device. You must turn on
the device to start a new training.
Q6.3. How to activate compass function?
A6.3: To activate compass function, device must be in motion with GPS located.
(When GO-TO function is in use, compass function will be disabled and
the “N” character in compass area will not be shown.)
Q6.4. How to charge your device?
A6.4: You can charge your device by plugging in USB/Power cable and display
will show “FULL” when charging completes. While plugging in USB/Power
cable, you will be forced to leave training mode and your training data will
be saved immediately.
Q7. Where to download the “Training Gym Pro” PC software?
A7: You can visit our official website “http://www.globalsat.com.tw/” and search “GB-1000” to
download from product page.
Q7.1. What can PC software do?
A7.1: PC software can help you check your training data by showing training files, training
information, data graphs...etc.
Training Gym Pro PC Software Screenshot
Q8. How to connect device to PC software?
Connect to PC
via USB Cable
Any Mode
Trip will be saved automatically.
Please make sure you have installed the USB driver before connecting to PC software. (Please
check our official website “http://www.globalsat.com.tw/” and search “GB-1000” for details about
USB driver installation. )
After communicating
with PC software
Q9. How to upgrade system firmware?
Turn on device by
holding [Page Up] & [OK]
then [Power On]
device is off UPGRADE FIRMWARE?
unplug USB cable
when process completes
Choose “Configuration /
Firmware Upgrade” in PC
SW to start the process
Start PC
software
Connect
device and PC
via USB cable
PC MODE
9.1 You can leave firmware upgrade process by pressing [Power On/Off] for 3 sec. before PC
software starts “Configuration / Firmware Upgrade”.
9.2 If you encounter any interruption during firmware upgrade process, please press [Power
On/Off] for 3 sec. to turn off the device. Then, press [Page Up], [OK] & [Power On] to redo
firmware upgrade process.
9.3 Your training files, system configuration and total distance will be kept after firmware upgrade.
[OK/Setup]to
re-confirm
Total Distance
Reset
[OK/Setup]to
re-confirm
Total Distance
Reset
[Page Down] / [Page Up]
[OK]
Q10.
How do I know how long the recording time remains?
A10: System will show the recording time remaining in HOUR : MINUTE
format when you turn on/off the device. (ex: 2 hours and 11 minutes
left) Besides, you can also press [Page Up] in “START”page to see
the recording time remaining (keep pressing [Page Up] three times in
this page to go back to “START”page). Moreover, when there is no
memory space left, system will show “NO MEMORY”every one
minute to warn you while you are in training.
Q11. How to check firmware version?
A11: Press [Page Up] two times in “START”page and you can see the
firmware version. (ex: version 1308261) You can go back to
“START”page by pressing [Page Up] two times in this page.
GB-1000
Loading...