Page 1
1
Black
Cyan
Magenta
Yellow
Code: PFC42V
Date: 080122 Edition: 5 Op: DCR
4.2V
QUICK CHARGE
CORDLESS
SCREWDRIVER
PFC46V
INSTRUCTION MANUAL
Page 2
2
Contents
Warranty Power Tools
Whilst every effort is made to ensure your complete
satisfaction with this tool, occasionally, due to the mass
manufacturing techniques, a tool may not live up to our
required level of performance and you may need the
assistance of our service department.
This product is warranted for a 2-year period for home
domestic use from the date of the original purchase.
If found to be defective in materials or workmanship,
the tool or the offending faulty component will be repaired
or replaced free of charge with another of the same item.
A
small freight charge may apply. Proof of purchase is
essential. We reserve the right to reject any claim where
the purchase cannot be verified.
This warranty does not include damage or defects to the
tool caused by or resulting from abuse, accidents,
alterations or commercial or business use. It also does not
cover any bonus items or included accessories. Only the
power tool is covered under this warranty.
With continuing product development, changes may have
occurred which render the product received slightly
different to that shown in this instruction manual.
Please ensure that you store your receipt in a safe place.
Conditions apply to the above warranty. For full details of
the warranty terms and conditions please refer to our
website – www.gmcompany.com
For prompt service we suggest you log your service
request online - www.gmcservice.com.au, should you
not have access to the internet, please contact our
service department on 1300 880 001 (Australia)
or 0800 445 721 (New Zealand).
Warranty 2
Introduction 3
Environmental protection 3
Description of symbols 3
Specifications 3
Safety instructions 4
Additional safety instructions
for cordless screwdrivers 5
Additional safety instructions for the charger 6
When to charge the tool 8
Know your product 9
Unpacking 10
Important information – special product care 10
Charging 10
To obtain the best life for the tool 11
Using the screwdriver 11
Maintenance 12
Page 3
3
Description of symbols
The rating plate on your tool may show symbols.
These represent important information about the
product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Conforms to relevant standards
for electromagnetic compatibility.
Specifications
Voltage: 4.2V
Cell type: Capacitor
Charger: 230 – 240V ~ 50Hz 55W
Charging time: 45 Seconds
No load speed: 170min
-1
Torque: 4.5 Nm
Bit retainer size: 6.35mm (1/4”)
Tool weight: 0.36kg
Introduction
Your new GMC power tool will more than satisfy
your expectations. It has been manufactured under
stringent GMC Quality Standards to meet superior
performance criteria.
You will find your new tool easy and safe to operate,
and, with proper care, it will give you many years
of dependable service.
CAUTION. Carefully read through this entire Instruction
Manual before using your new GMC Power Tool. Take
special care to heed the Cautions and Warnings.
Your GMC power tool has many features that will make
your job faster and easier. Safety, performance, and
dependability have been given top priority in the
development of this tool, making it easy to maintain
and operate.
Environmental protection
Recycle unwanted materials instead
of disposing of them as waste. All tools,
hoses and packaging should be sorted,
taken to the local recycling centre and
disposed of in an environmentally safe way
.
Page 4
4
Safety instructions
WARNING. Read all instructions. Failure to follow all
instructions listed below may result in electric shock, fire and/
or serious injury. The term “power tool” in all of the warnings
listed below refers to your mains operated (corded) power
tool or battery or capacitor operated (cordless) power tool.
Save these instructions
1. Work area
a. Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet.
Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk
of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
b. Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c. Avoid accidental starting. Ensure the switch is in the
off position before plugging in. Carrying power tools with
your finger on the switch or plugging in power tools that
have the switch on invites accidents.
d. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices
can reduce dust related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
Page 5
5
c. Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power tool
for operations different from those intended could result
in a hazardous situation.
5. Battery tool use and care
a. Ensure the switch is in the off position before
inserting battery pack. Inserting the battery pack into
power tools that have the switch on invites accidents.
b. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
c. Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
d. When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
e. Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from
the battery may cause irritation or burns.
6. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional safety instructions
for cordless screwdrivers
Loss of control can cause personal injury.
• If possible, always use clamps or a vice to hold your work.
• Always switch off before you put the tool down.
• Ensure that the lighting is adequate.
• Do not put pressure on the screwdriver, such that it slows
the motor down. Allow the screwdriver to operate without
pressure. You will get better results and you will be taking
better care of your tool.
• Keep the area free of tripping hazards.
• Do not let anyone under 18 years operate this tool.
• Only use accessory bits in good condition.
• Before screwdriving, check that there is sufficient
clearance under the workpiece.
• Do not touch the bit after operation. It will be very hot.
• Keep your hands away from under the workpiece.
• Never use your hands to remove sawdust, chips or waste
close by the bit.
Page 6
6
• Rags, cloths, cord, string and the like should never be left
around the work area.
• Support the work properly.
• If you are interrupted when operating, complete the
process and switch off before looking up.
• Periodically check that all nuts, bolts and other fixings are
properly tightened.
• When using the screwdriver, use safety equipment
including safety glasses or shield, ear defenders, and
protective clothing including safety gloves.
• Do not charge the screwdriver in a place where static
electricity is generated nor let the battery touch something
that is statically charged.
• Take care where the tool is stored. Do not store in areas
of corrosive fumes, or salt air or similar conditions.
• Do not dispose of the tool in a fire or put the tool into
a microwave oven, conventional oven, dryer, or highpressure container. Under these conditions, the tool
may explode.
• Never attempt to open the tool, puncture the casing of
the tool, or subject the tool to strong physical shock. If
the plastic housing of the tool breaks open or cracks,
immediately discontinue its use and do not recharge it.
• Stop using the tool if it exhibits abnormal heat, colour or
deformation, or if the tool is in an abnormal condition.
• After the tool has reached the end of its useful life,
we recommend recycling the materials at your local
municipal council recycling centre. DO NOT attempt to
replace the capacitor, repair or modify any part of the tool.
• When recycling, make it nonconductive by applying
insulating tape to cover the terminals located on the
bottom of the screwdrivers body.
If in doubt, do not plug in the tool. Using a power source with
a voltage less than the nameplate rating is harmful to the motor.
The tool must be used only for its prescribed purpose.
Any use other than those mentioned in this Manual will
be considered a case of misuse. The user and not the
manufacturer shall be liable for any damage or injury
resulting from such cases of misuse.
To use this tool properly, you must observe the safety
regulations, the assembly instructions and the operating
instructions to be found in this Manual. All persons who use
and service the machine have to be acquainted with this
Manual and must be informed about its potential hazards.
Children and frail people must not use this tool. Children
should be supervised at all times if they are in the area in
which the tool is being used. It is also imperative that you
observe the accident prevention regulations in force in your
area. The same applies for general rules of occupational
health and safety.
The manufacturer shall not be liable for any changes made
to the tool nor for any damage resulting from such changes.
Even when the tool is used as prescribed it is not possible to
eliminate all residual risk factors. The following hazards may
arise in connection with the tool’s construction and design:
• Damage to the lungs if an effective dust mask is not worn.
• Damage to hearing if effective ear defenders are not worn.
Additional safety instructions for the charger
• Your GMC quick charge screwdriver uses 2 capacitors
to store the energy that operates the screwdriver. Do not
attempt to charge the screwdriver with any other charger
than the one supplied. IT IS DANGEROUS TO USE ANY
OTHER CHARGER TO CHARGE YOUR TOOL.
• Do Not attempt to charge any other types of rechargeable
batteries OR non rechargeable battery cells with this charger.
• If there is a problem with the charger or the tool, take
it to your nearest Authorised Service centre or phone
and speak with an experienced GMC Customer Service
Representative for assistance in rectifying your problem.
• Before using the charger, read all the instructions, labels
and cautionary markings on the charger and screwdriver.
Page 7
7
• Do not use the charger if it has been subjected to a
heavy knock, dropped or otherwise damaged in anyway.
Take the charger to an authorised service centre for a
check or repair.
• Do not disassemble the charger. Phone and speak with
an experienced GMC Customer Service Representative or
contact an Authorised Service centre for assistance. Opening
or removing covers may expose you to dangerous voltages
or other risks. Incorrect reassembly can cause electric shock
when you use the tool or charger again. Take the charger
to an authorised service centre when service or repair is
required. Incorrect re-assembly may result in the risk of fire,
electric shock or electrocution. To reduce the risk of electric
shock, do not disassemble any part of the product.
• DANGER. If the screwdriver is cracked or damaged in
any other way, do not insert it in the charger
• Do not plug anything other than your GMC quick charge
screwdriver into the charger, as other objects may touch
dangerous voltage points or short out parts, which could
result in fire or electric shock.
• Do not place the tool or charger on an uneven surface,
as a fall may cause serious damage.
• Never place the tool or charger near or over a heat
source such as a radiator or heater.
Do not operate the charger in a cabinet or other
enclosure unless proper ventilation is provided.
• Use the battery charger indoors only.
• WARNING. Do not allow any liquid to come into contact
with the charger. There is a danger of electric shock.
Do not position the tool or battery charger near water;
for example, near a sink, wash bowl or toilet. Do not
spill liquid of any kind on the tool or charger. Doing so
may short out parts, causing damage to the product and
creating the risk of fire or electric shock.
• Take the tool or charger to your nearest Authorised
Service centre or phone and speak with an experienced
GMC Customer Service Representative for assistance in
these circumstances:
• If liquid has been spilled into the tool or charger, or if rain
or water has touched the screwdriver or charger.
• If the tool or charger does not operate normally after you
follow the operating instructions.
• If the tool or charger has been dropped or damaged.
• If the tool or charger exhibits a distinct degradation in
performance.
• If the tool or charger is damaged in any way.
• If the screwdriver is not charged within the time frame as
specified in this manual, turn charger off.
• To reduce the risk of an electric shock, unplug the
charger from the power supply before attempting to clean
it. To clean tool or charger, wipe with a damp cloth. Use
of any other cleaners is not recommended.
• Do not place any object on to, or allow anything to rest
on the charger.
• Make sure that the charger cable is positioned where
it will not be stepped on, tripped over or otherwise
subjected to damage or stress. Keep the lead away
from operating machinery.
• Do not pull on the lead of the charger to disconnect it
from the mains power socket.
• Do not use an extension cord unless it is absolutely
necessary. The use of an improper extension cord could
cause the risk of fire, electric shock or electrocution.
• Never attempt to connect two chargers together.
• Do not charge or use the tool in locations where the
temperature may be below 0°C or exceed 40°C such as
alongside sheds or metal structures.
• The screwdriver can be charged or operated at
temperatures between 0° C and 40° C.
The most suitable temperatures to charge the screwdriver
are between 20 - 25° C.
Page 8
8
When to charge the tool
• New tools are shipped in a low charge condition and
must be fully charged before use. It takes approximately
45 seconds to fully charge the tool.
• Charging the tool should not be undertaken casually.
Through the charging cycle monitor the tool and make
sure that screwdriver is charging. This can be done by
reviewing the charging process indicators (6) and the
charge cycle completed indicator (5).
Note. You may use the screwdriver at any time. The
charging process does not have to be completed to use
the tool and short chargers will not harm the tool.
Page 9
9
1
Know your product
This screw driver is for light to medium applications
of screws and small nuts and bolts. If the screw
driver is unable to rotate the fastener do not over
load by holding the switch in the on position and
manually rotating the fastener.
1. Chuck/Bit retainer
2. Handle adjusting switch
3. Forward/Reverse switch
4. Trigger
5. Charge cycle completed indicator
6. Charging process indicators
7. Charger
8. Charger power cord
9. Accessory bits storage
10. Power on indicators
3
8
2
5
6
7
9
10
4
Page 10
10
Unpacking
Due to modern mass production techniques, it is unlikely
that your GMC Power Tool is faulty or that a part is missing.
If you find anything wrong, do not operate the tool until the
parts have been replaced or the fault has been rectified.
Failure to do so could result in serious personal injury.
Important information – special product care
Your GMC quick charge screwdriver uses capacitors to
store the energy that operates the screwdriver. Do not
attempt to charge the screwdriver with any other charger
than the one supplied. IT IS DANGEROUS TO USE ANY
OTHER CHARGER TO CHARGE YOUR TOOL. Ensure
you have read all of the safety notes in the previous pages
before using the screwdriver.
Charging
IMPORTANT. Before plugging in the charger (7) into the
mains power supply always ensure that the mains power
switch is turned off.
IMPORTANT. The tool will be fully charged after approximately
45 seconds. The screwdriver can remain in the charger,
with the charger turned on without damage being done to
the cells (Note. Do not leave the screwdriver in the charger
turned on unattended).
1. Place the screwdriver into
the charger (7) vertically with
the bottom of the screwdriver
aligning with the charger as
per the picture shown. Push
the screwdriver down until it
is securely in place.
Note. If the screwdriver is
incorrectly orientated the
screwdriver will not fit securely
in the base.
2. Plug in the charger and switch
on at the power supply. The
power on indicators (10)
will glow signalling that the
charger has power connected
to it. The screwdriver will
now begin charging. While
the screwdriver is charging
the charging indicators (6)
will glow signalling that the
screwdriver is in the charging
process. When the screwdriver
charging process is complete
the charge cycle completed
indicator (5) will glow advising
that the charge cycle has been
completed.
Note. The charge cycle
completed indicator (5) will only
glow when the the screwdriver
charger (7) is plugged in and is
turned on.
The charging time is complete
in 45 seconds.
Note. You may use the screwdriver
at any time. The charging process
does not have to be completed to
use the tool and short chargers
will not harm the tool.
3. The charging time is
approximately 45 seconds.
Once the screwdriver has
completed it’s charge or once
the charge has reached a
suitable level for the task at hand, simply remove the
screwdriver from the charger.
Note. Do not leave the charger turned on and unattended.
Page 11
11
To obtain the best life for the tool
The screwdriver should be placed on charge when ever
the tool no longer can perform tasks previously achieved.
Do Not completely run down the charge. DO NOT continue
to use the screwdriver when the charge is exhausted. The
screwdriver does not have automatic spindle lock and using
the screwdriver with no charge may damage the tool.
During operation avoid overloading the screwdriver.
Doing so will allow you to maximise the charge run time.
Avoid allowing loose items like screws or nails etc. to be
stored with tool as these or similar items can short battery
packs and cause a fire or explosion.
Always unplug the charger when not in use and store in
a dry secure place.
Using the screwdriver
Trigger switch
Use the forward/reverse switch
(3) to select the direction of
rotation, then pull the trigger
(4). To stop the drill, release the
trigger switch (4).
Direction of Rotation/Forward
and Reverse
Note. You can only change the
direction of rotation of the drill
using the forward/reverse switch
(3) when the trigger (4) is NOT
depressed.
This switch will allow you to
change the direction of the
motor while the trigger switch
is not depressed.
The forward mode is used for
drilling and tightening screws.
The reverse mode is intended
for the removal of screws and
assisting to remove jammed
drill bits.
Adjusting the handle
The handle can be turned to one of two positions to suit the
task at hand. The tool can be used as a straight handled
screwdriver or as a pistol grip screwdriver.
1. To change the position of the handle, push the handle
adjusting switch (2) in and twist the handle to the
desired position.
2. Release the switch (2) to lock the handle in the new position.
Page 12
12
Inserting and removing bits
1. Select an appropriate bit and
Insert it into the hexagonal
hole in the chuck/bit retainer
(1). The screwdriver is now
ready for use.
2. To remove the screwdriver bit
you simply remove the existing
bit by pulling the bit out of the
chuck/bit retainer (1).
Maintenance
• Store the tools, instruction manual and where necessary
the accessories in the original packaging. In this way you
will always have all the information and parts on hand.
• If the cordset of the charger is damaged or worn, have it
repaired or replaced by an authorised service centre in
order to avoid a hazard.
• Service to the tool should only be performed by qualified
repair persons using identical replacement parts. This will
ensure the safety of the power tool.
Page 13
131415
Page 14
Page 15
Page 16
GMC customer assist
If your product needs repairing, replacing,
technical service or you simply need help or advice,
please contact us on our Customer Assist Line
1300 880 001 (Australia) or 0800 445 721 (New Zealand).
For prompt service we suggest you log your service request
online at www.gmcservice.com.au. Should you not have
access to the Internet, please contact our service department
on 1300 880 001 (Australia) or 0800 445 721 (New Zealand).
7am –7pm, 7days a week (AEST).
Please note that if repair or replacement is required,
you must provide a valid original purchase receipt.
You will need the following details at hand to log your service request;
Personal details: First & Last name, address, pick up address,
contact phone numbers, email address
Product details: Product number, date of purchase, retailer bought from,
State & postcode, receipt number,
reason for the request,
c
opy of official purchase receipt
Attach your purchase receipt and save with this Manual for future reference
.
Please refer to our website www.gmcompany.com for full GMC warranty Terms and Conditions.
Loading...