Global Machinery Company EAC40, EAC30 User Manual
1
30L & 40L
AIR COMPRESSORS
EAC30 & EAC40
INSTRUCTION MANUAL
Do not switch on
for the first time
without first
filling with oil.
2
Contents
Warranty Power Tools
Whilst every effort is made to ensure your complete
satisfaction with this tool, occasionally, due to the mass
manufacturing techniques, a tool may not live up to our
required level of performance and you may need the
assistance of our service department.
This product is warranted for a 2-year period for home
domestic use from the date of the original purchase.
If found to be defective in materials or workmanship,
the tool or the offending faulty component will be repaired
or replaced free of charge with another of the same item.
A
small freight charge may apply. Proof of purchase is
essential. We reserve the right to reject any claim where
the purchase cannot be verified.
This warranty does not include damage or defects to the
tool caused by or resulting from abuse, accidents,
alterations or commercial or business use. It also does not
cover any bonus items or included accessories. Only the
power tool is covered under this warranty.
With continuing product development, changes may have
occurred which render the product received slightly
different to that shown in this instruction manual.
Please ensure that you store your receipt in a safe place.
Conditions apply to the above warranty. For full details of
the warranty terms and conditions please refer to our
website – www.gmcompany.com
For prompt service we suggest you log your service
request online - www.gmcservice.com.au, should you
not have access to the internet, please contact our
service department on 1300 880 001 (Australia)
or 0800 445 721 (New Zealand).
Warranty 2
Warning labels explained 3
Introduction 4
Environmental protection 4
Description of symbols 4
Specifications 4
General safety instructions 5
Additional safety rules for air compressors 6
Contents of carton 7
Know your product 8
Unpacking 9
Assembly 9
Pre-start routine 10
To start & stop the compressor 10
Operation 11
Troubleshooting 12
Maintenance 14
General inspection 14
Cleaning 14
Power cord maintenance 14
3
Do not switch on
for the first time
without first
filling with oil.
Air discharged from
this unit is not
suitable for human
consumption.
Test the safety relief
valve daily.
Refer the instruction
manual.
Keep oil level as shown:
Use only oil grade
specified in instruction
manual.
To prevent build-up of
condensation, open
drain cock daily
When filter becomes
dirty or oily, clean or
replace filter. Refer to
instruction manual.
High voltage used on
this equipment. Switch
off power supply &
remove plug from mains
before removing any
covers. Ensure mains
outlet is adequately
rated for this unit.
Unit starts
automatically.
Switch off power supply,
remove plug & relieve
air pressure prior to
commencing service
tasks.
Read instruction manual
prior to starting unit.
This equipment
operates from
AC mains only.
Warning labels explained
On the tank of your air compressor you will notice various
warnings about the operation of the compressor. These
warnings and the procedures associated with them are
explained fully in this manual on the following pages.
Please take note of these. They are important for your
safety and that of others in the vicinity.
4
Description of symbols
The rating plate on your tool may show symbols.
These represent important information about the
product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Double insulated for additional protection.
Conforms to relevant standards
for electromagnetic compatibility.
Specifications
EAC30 EAC40
Power: 2HP/1600W
Voltage: 230–240V ~ 50Hz
No load speed: 2850 min-1 2850 min
-1
Discharge pressure: 0.8 MPa(115 psi) 0.8 MPa(115 psi)
Tank capacity: 30 litres 40 litres
Air outlet size: 6.35mm (1/4”) 6.35mm (1/4”)
Net weight: 29kgs 34kgs
Cut-in pressure (factory set): 0.6MPa (85psi)
Cut-out pressure (factory set): 0.8MPa (115psi)
Maximum output pressure: 0.8MPa (115psi)
Free air delivery: 127 l/min 150 l/min
(4.5 CFM) (5.4 CFM)
Pump displacement: 206 l/min 216 l/min
(7.2CFM) (7.65CFM)
Introduction
Your new GMC power tool will more than satisfy
your expectations. It has been manufactured under
stringent GMC Quality Standards to meet superior
performance criteria.
You will find your new tool easy and safe to operate,
and, with proper care, it will give you many years
of dependable service.
CAUTION. Carefully read through this entire Instruction
Manual before using your new GMC Power Tool. Take
special care to heed the Cautions and Warnings.
Your GMC power tool has many features that will make
your job faster and easier. Safety, performance, and
dependability have been given top priority in the
development of this tool, making it easy to maintain
and operate.
Environmental protection
Recycle unwanted materials instead
of disposing of them as waste. All tools,
hoses and packaging should be sorted,
taken to the local recycling centre and
disposed of in an environmentally safe way
.
5
General safety instructions
To use this tool properly, you must observe the safety
regulations, the assembly instructions and the operating
instructions to be found in this Manual. All persons who use
and service the machine have to be acquainted with this
Manual and must be informed about its potential hazards.
Children and infirm people must not use this tool. Children
should be supervised at all times if they are in the area in
which the tool is being used. It is also imperative that you
observe the accident prevention regulations in force in your
area. The same applies for general rules of occupational
health and safety.
WARNING. When using power tools, basic safety precautions
should always be taken to reduce the risk of fire, electric
shock and personal injury. Also, please read and heed the
advice given in the additional important safety instructions.
1. Keep the work area clean and tidy. Cluttered work areas
and benches invite accidents and injury.
2. Consider the environment in which you are working.
Do not use power tools in damp or wet locations. Keep
the work area well lit. Do not expose power tools to rain.
Do not use power tools in the presence of flammable
liquids or gases.
3. Keep visitors away from the work area. All visitors and
onlookers, especially children and infirm persons, should
be kept well away from where you are working. Do not
let others in the vicinity make contact with the tool or
extension cord.
4. Store tools safely. When not in use, tools should be
locked up out of reach.
5. Do not force the tool. The tool will do the job better and
safer working at the rate for which it was designed.
6. Use the correct tool for the job. Do not force small tools
or attachments to do the job best handled by a heavier
duty tool. Never use a tool for a purpose for which it was
not intended.
7. Dress correctly. Do not wear loose clothing or
jewellery. They can be caught in moving parts. Rubber
gloves and non-slip footwear are recommended when
working outdoors. If you have long hair, wear a protective
hair covering.
8. Use safety accessories. Safety glasses and earmuffs
should always be worn. A face or dust mask is also
required if the sanding operation creates dust.
9. Do not abuse the power cord. Never pull the cord to
disconnect the tool from the power point. Keep the cord
away from heat, oil and sharp edges.
10. Secure the work piece. Use clamps or a vice to hold the
work piece. It is safer than using your hand and frees
both hands to operate the tool.
11. Do not overreach. Keep your footing secure and
balanced at all times.
12. Look after your tools. Keep tools sharp and clean for
better and safer performance. Follow the instructions
regarding lubrication and accessory changes. Inspect
tool cords periodically and, if damaged, have them
repaired by an authorised service facility. Inspect
extension cords periodically and replace them if
damaged. Keep tool handles dry, clean and free from oil
and grease.
13. Disconnect idle tools. Switch off the power and
disconnect the plug from the power point before
servicing, when changing accessories and when the tool
is not in use.
14. Remove adjusting keys and wrenches. Check to see
that keys and adjusting wrenches are removed from the
tool before switching on.
15. Avoid unintentional starting. Always check that the
switch is in the OFF position before plugging in the tool
to the power supply. Do not carry a plugged in tool with
your finger on the switch.
16. Use outdoor rated extension cords. When a tool is used
outdoors, use only extension cords that are intended for
outdoor use and are so marked.
17. Stay alert. Watch what you are doing. Use common
sense. Do not operate a power tool when you are tired.
Loading...