Global Industrial 641430 User Manual

2505 Mill Center Parkway, Buford, GA 30518

1-800-645-1232

Horizontal Baby Changing Station

Installation Instructions

Instructions d’installation de la station

à langer horizontale

Instrucciones para la instalación de la

estación horizontal para cambiar pañales

Models Included / Les Modèles Inclus / Modelos Incluídos:

641430

WARNING

• Failure to follow these warnings and the installation instructions could result in serious injury

or

discard.

death.

all instructions before installing

diaper changing station. Keep these instructions. DO NOT

AVERTISSEMENT

• Le

• Lisez attentivement toutes les instructions avant d’installer la station à langer. Conservez ces

non

respect de ces avertissements et instructions d’installation peut entraîner des blessures
ou

la mort.

NE

les

jetez PAS.

ADVERTENCIA

• El no seguir estas advertencias y las instrucciones para la instalación podría causar lesiones

muerte.

o la

• Lea todas las instrucciones antes de instalar la estación para cambiar pañales. Guarde estas
NO las deseche.

AB20341A

ASSEMBLY INSTRUCTIONS

ADULT INSTALLATION REQUIRED.
TOOLS REQUIRED:

Power drill with 7/32”, 1/8” and 1/2” masonry bits (C)

(A)

Level
Measuring tape

screwdriver with bull nose phillips bit (D)

Power

(B)

A

C

D

B

•

• Unpack carton and identify all parts.

ALL INSTRUCTIONS BEFORE ASSEMBLY of Diaper Changing Station.

READ

PARTS LIST

Parts Description Quantity

Hardware for installation:
3” Wood Screws 4
3/4” Finishing Washers 4
3” Machine Screws 2
3/4” Flat Washers 4
Toggle Anchors 2
1-1/4” Caps 6

3” Wood Screws

For Wood Studs:

3/4” Finishing Washers

3/4” Flat Washers

3” Machine Screws

For Use With Toggle Anchors:

3/4” Flat Washers

34-1/4”

(870 mm)

17-1/2”

(445 mm)

Toggle Anchors

15-3/8”

(390 mm)

1

1-1/4” Caps

A.D.A. Compliance:

306.3 Knee Clearance

307.2 Maximum Protruding Objects

308.2 Forward Reach

308.3 Side Reach

309.4 Operation

902.3 Work Surface
Compliant when properly installed.

•

WARNING

A

MUST be located and used for at least one side of the diaper changing station.

stud

•

if

The diaper changing station is no stronger than the anchors or walls to which they are attached and, therefore, MUST be

secured in order to support the weight they are intended to support. Contact an architect or building contractor

any questions.

INSTALLATION

1. Locate wood stud where left side of changing station will be mounted to the wall.

2. Measure up 42” (107 cm) from the and mark the wall. This locates the position
for the top left attachment hole.

NOTE: Mark on wall MUST be in center of wood stud.

3. Align hole in top left corner of changing station with mark on wall and hold in place.

4. Using a level and measuring tape, mark the remaining three (3) holes. After marking holes,
set changing station down on ground.

5. Use a power drill and appropriate bit to drill four (4) holes in the wall. This may require
2 people.

NOTE 1: For wood studs:

a 7/32” masonry bit for the pilot hole until you hit the wood

- If finished

stud, then change to 1/8” bit.

- Use wood screws, finishing washers and

NOTE 2: For use with toggle anchors:

has metal studs, or has an underlying surface of concrete block,
use 1/2” bit.

- For holes NOT located in a wood stud, toggle anchors MUST be
used (Fig. c). See “Using Toggle Anchors” section.

wall surface is tile or masonry over wood studs, use

washers (Fig. a).

machine

wall surface

screws

has wood studs that are not 16” on center,

and washers

(Fig. b)

.

Flat

Washer

Finishing

Washer

Wood

Screw

Changing

Changing

Station

Wood Stud

Station

Wood Stud

Fig. a

Toggle
Anchor

Flat

Washer

Machine

Screw

Fig. b

6. Align holes in changing station with drilled holes and secure top left corner of changing
station to wall stud using the appropriate screw and washer. Continue to secure the
three (3) remaining corners using the appropriate screws and washers as described
in Note 1 or Note 2.

installation through the metal brackets.

All 4 of these locations MUST be used for safe installation. The lower holes ensure

7. Ensure all four (4) screws are tight and snap caps over screw heads.

Using Toggle Anchors:

1. Insert metal end of toggle anchor into 1/2” hole.

2. Slide zip strip down snugly against wall.

3. Snap off break-away pieces of toggle anchor (Fig. d).

4. Align holes in changing station with toggle anchors and secure top left corner of changing station to

wall

using

machine screws and washers. Continue to secure the three (3) remaining corners

using

machine screws and washers.

WARNING

Wood Stud

Break-Away

Fig. c

Toggle
Anchor

Fig. d

5. Ensure all four (4) screws are tight and snap caps over screw heads.

2