Page 1
SAFETY DATA SHEET
Issue Date 13-Mar-2017 Revision Date 13-Mar-2017 Version 3
1. PRODUCT AND COMPANY IDENTIFICATION
Product identifier
Product Name
Other means of identification
Product Code
Synonyms
Details of the supplier of the safety data sheet
Company Name
Emergency telephone number
Emergency Telephone
Classification
Ultra High Speed Floor Finish
640403
None
Global Industrial
2505 Mill Center Parkway, Buford, GA 30518
(888) 978-7759
Chemtrec (US &Canada) 800-424-9300
Chemtrec (outside US & Canada) 703-527-3887
2. HAZARDS IDENTIFICATION
OSHA Regulatory Status
This product has been classified in accordance with the 2012 OSHA Hazard Communication Standard (29 CFR 1910.1200)
Acute toxicity - Oral Not classified
Acute toxicity - Dermal Not classified
Label elements
Emergency Overview
Appearance White Emulsion Physical state Liquid Odor Typical Acrylic Polymer
Precautionary Statements - Response
Immediately call a POISON CENTER or doctor/physician
Specific Treatment (See Section 4 on the SDS)
Precautionary Statements - Disposal
Disposal should be in accordance with applicable regional, national and local laws and regulations
Hazards not otherwise classified (HNOC)
Other Information
• Harmful to aquatic life with long lasting effects
• Harmful to aquatic life
Unknown Acute Toxicity 0% of the mixture consists of ingredient(s) of unknown toxicity
3. COMPOSITION/INFORMATION ON INGREDIENTS
Chemical Name CAS No. Weight-% Trade Secret
_____________________________________________________________________________________________
Page 1 / 7
Page 2
640403 Ultra High Speed Floor Finish Revision Date 13-Mar-2017
_____________________________________________________________________________________________
Tributoxyethyl Phosphate 78-51-3 1-5 *
*The exact percentage (concentration) of composition has been withheld as a trade secret.
4. FIRST AID MEASURES
First aid measures
Skin Contact
Eye contact
Inhalation
Ingestion
Most important symptoms and effects, both acute and delayed
Symptoms
Indication of any immediate medical attention and special treatment needed
Note to physicians
Wash off immediately with plenty of water. Wash skin with soap and water.
Rinse thoroughly with plenty of water for at least 15 minutes, lifting lower and upper eyelids.
Consult a physician.
Remove to fresh air.
Clean mouth with water and drink afterwards plenty of water.
Any additional important symptoms and effects are described in Section 11: Toxicology
Information.
Treat symptomatically.
5. FIRE-FIGHTING MEASURES
Suitable extinguishing media
Use extinguishing measures that are appropriate to local circumstances and the surrounding environment.
Unsuitable extinguishing media
Specific hazards arising from the chemical
No Information available.
Caution: Use of water spray when fighting fire may be inefficient.
Explosion data
Sensitivity to Mechanical Impact
Sensitivity to Static Discharge
Protective equipment and precautions for firefighters
As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH (approved or equivalent) and full
protective gear.
None.
None.
6. ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures
Personal precautions
Environmental precautions
Environmental precautions
Methods and material for containment and cleaning up
Methods for containment
Methods for cleaning up
Ensure adequate ventilation, especially in confined areas.
See Section 12 for additional ecological information.
Prevent further leakage or spillage if safe to do so.
Pick up and transfer to properly labeled containers.
7. HANDLING AND STORAGE
Precautions for safe handling
Page 3
640403 Ultra High Speed Floor Finish Revision Date 13-Mar-2017
_____________________________________________________________________________________________
Advice on safe handling
Handle in accordance with good industrial hygiene and safety practice.
Conditions for safe storage, including any incompatibilities
Storage Conditions
Incompatible materials
Keep containers tightly closed in a dry, cool and well-ventilated place.
None known based on information supplied.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Control parameters
Exposure Guidelines
Chemical Name ACGIH TLV OSHA PEL NIOSH IDLH
2-(2-methoxypropoxy)propano
34590-94-8
NIOSH IDLH Immediately Dangerous to Life or Health
Other Information
Appropriate engineering controls
.
STEL: 150 ppm
TWA: 100 ppm
S*
Vacated limits revoked by the Court of Appeals decision in AFL-CIO v. OSHA, 965 F.2d 962
(11th Cir., 1992).
TWA: 100 ppm
TWA: 600 mg/m
(vacated) TWA: 100 ppm
(vacated) TWA: 600 mg/m
(vacated) STEL: 150 ppm
(vacated) STEL: 900 mg/m
(vacated) S*
S*
3
IDLH: 600 ppm
TWA: 100 ppm
3
3
TWA: 600 mg/m
STEL: 150 ppm
STEL: 900 mg/m
3
3
Engineering Controls
Showers, Eyewash stations & Ventilation systems.
Individual protection measures, such as personal protective equipment
Eye/face protection
Skin and body protection
Respiratory protection
Wear safety glasses with side shields (or goggles).
Wear protective gloves and protective clothing.
If exposure limits are exceeded or irritation is experienced, NIOSH/MSHA approved
respiratory protection should be worn. Positive-pressure supplied air respirators may be
required for high airborne contaminant concentrations. Respiratory protection must be
provided in accordance with current local regulations.
General Hygiene
Handle in accordance with good industrial hygiene and safety practice.
9. PHYSICAL AND CHEMICAL PROPERTIES
Information on basic physical and chemical properties
Physical state
Appearance
Color
Odor
Odor threshold
Property Values Remarks • Method
pH
Specific Gravity
Viscosity
Melting point/freezing point
Flash point
Boiling point / boiling range
Evaporation rate
Flammability (solid, gas)
Flammability Limits in Air
Liquid
White Emulsion
White
Typical Acrylic Polymer
No Information available
8.0 - 9.0
1.03
< 25 cP @ 25°C
No Information available
None
100 °C / 212 ° F Degrees
No Information available
No data available
Page 4
640403 Ultra High Speed Floor Finish Revision Date 13-Mar-2017
_____________________________________________________________________________________________
Upper flammability limit:
Lower flammability limit:
Vapor pressure
Vapor density
Water solubility
Partition coefficient
Autoignition temperature
Decomposition temperature
No Information available
No Information available
No Information available
No Information available
Emulsifies
No Information available
No Information available
No Information available
Other Information
Density Lbs/Gal
VOC Content (%)
8.56
2.823
10. STABILITY AND REACTIVITY
Reactivity
No data available
Chemical stability
Stable under recommended storage conditions.
Possibility of Hazardous Reactions
None under normal processing.
Conditions to avoid
Extremes of temperature and direct sunlight.
Incompatible materials
None known based on information supplied.
Hazardous Decomposition Products
None known based on information supplied.
11. TOXICOLOGICAL INFORMATION
Information on likely routes of exposure
Product Information
Inhalation
Eye contact
Skin Contact
Ingestion
Chemical Name Oral LD50 Dermal LD50 Inhalation LC50
Tributoxyethyl Phosphate
78-51-3
Information on toxicological effects
Symptoms
Avoid breathing vapors or mists. Inhalation of vapors in high concentration may cause
irritation of respiratory system.
Avoid contact with eyes. Contact with eyes may cause irritation.
Avoid contact with skin. Prolonged or repeated contact may dry skin and cause irritation.
Do not taste or swallow. Ingestion may cause irritation to mucous membranes.
= 3 g/kg ( Rat ) > 16 mL/kg ( Rabbit ) > 6.4 mg/L ( Rat ) 4 h
No Information available.
Delayed and immediate effects as well as chronic effects from short and long-term exposure
Sensitization
Germ cell mutagenicity
Carcinogenicity
Reproductive toxicity
STOT - single exposure
No Information available.
No Information available.
No Information available.
No Information available.
No Information available.
Page 5
640403 Ultra High Speed Floor Finish Revision Date 13-Mar-2017
_____________________________________________________________________________________________
STOT - repeated exposure
Aspiration hazard
No Information available.
No Information available.
Numerical measures of toxicity - Product Information
Unknown Acute Toxicity
0% of the mixture consists of ingredient(s) of unknown toxicity
The following values are calculated based on chapter 3.1 of the GHS document .
ATEmix (oral)
ATEmix (dermal)
ATEmix (inhalation-dust/mist)
8,048.00
35,928.00
265.73
12. ECOLOGICAL INFORMATION
Ecotoxicity
23.62685688% of the mixture consists of components(s) of unknown hazards to the aquatic environment
Chemical Name Algae/aquatic plants Fish Crustacea
Tributoxyethyl Phosphate
78-51-3
2-(2-ethoxyethoxy)ethanol
111-90-0
[2-(2-Methoxymethylethoxy)methyle
thoxy]-propanol
25498-49-1
2-(2-methoxypropoxy)propano
34590-94-8
Methyl Chloro Isothiazolinone
26172-55-4
Magnesium Chloride
7786-30-3
Pseudokirchneriella subcapitata
mg/L EC50 static 0.03 - 0.13: 96 h
Pseudokirchneriella subcapitata
mg/L EC50 static 0.31: 120 h
Anabaena flos-aquae mg/L EC50
2200: 72 h Desmodesmus
subspicatus mg/L EC50
- 10.4 - 12.0: 96 h Pimephales
- 10000: 96 h Lepomis macrochirus
- 11619: 96 h Pimephales promelas
- 10000: 96 h Pimephales promelas
0.11 - 0.16: 72 h
promelas mg/L LC50 flow-through
mg/L LC50 static 19100 - 23900: 96
h Lepomis macrochirus mg/L LC50
flow-through 13400: 96 h Salmo
gairdneri mg/L LC50 flow-through
11400 - 15700: 96 h Oncorhynchus
mykiss mg/L LC50 flow-through
11600 - 16700: 96 h Pimephales
promelas mg/L LC50 flow-through
mg/L LC50 static
mg/L LC50 static
1.6: 96 h Oncorhynchus mykiss
mg/L LC50 semi-static
1970 - 3880: 96 h Pimephales
promelas mg/L LC50 static 4210: 96
h Gambusia affinis mg/L LC50 static
3940 - 4670: 48 h Daphnia magna
10: 48 h Daphnia magna mg/L
1919: 48 h Daphnia magna mg/L
4.71: 48 h Daphnia magna mg/L
EC50 0.12 - 0.3: 48 h Daphnia
magna mg/L EC50 Flow through
0.71 - 0.99: 48 h Daphnia magna
140: 48 h Daphnia magna mg/L
EC50 Static 1400: 24 h Daphnia
-
mg/L EC50
EC50
LC50
mg/L EC50 Static
magna mg/L EC50
Persistence and degradability
No Information available.
Bioaccumulation
Bioaccumulative potential.
Chemical Name Partition coefficient
Tributoxyethyl Phosphate
78-51-3
Other adverse effects
Waste treatment methods
Disposal of wastes
Contaminated packaging
3.65 - 4.78
No Information available
13. DISPOSAL CONSIDERATIONS
Disposal should be in accordance with applicable regional, national and local laws and
regulations.
Do not reuse container.
Page 6
640403 Ultra High Speed Floor Finish Revision Date 13-Mar-2017
_____________________________________________________________________________________________
This product contains one or more substances that are listed with the State of California as a hazardous waste.
14. TRANSPORT INFORMATION
The basic description below is specific to the container size. This information is provided for at a glance DOT information. Please
refer to the container and/or shipping papers for the appropriate shipping description before tendering this material for shipment.
For additional information, please contact the distributor listed in section 1 of this SDS.
DOT
TDG
Not regulated
Not regulated
15. REGULATORY INFORMATION
International Inventories
TSCA
DSL/NDSL
Legend:
TSCA - United States Toxic Substances Control Act Section 8(b) Inventory
DSL/NDSL - Canadian Domestic Substances List/Non-Domestic Substances List
US Federal Regulations
SARA 313
Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA). This product contains a chemical
or chemicals which are subject to the reporting requirements of the Act and Title 40 of the Code of Federal Regulations, Part 372
Chemical Name SARA 313 - Threshold Values %
2-(2-ethoxyethoxy)ethanol - 111-90-0 1.0
[2-(2-Methoxymethylethoxy)methylethoxy]-propanol - 25498-49-1 1.0
Zinc ammonium carbonate - 1.0
SARA 311/312 Hazard Categories
Acute health hazard
Chronic Health Hazard
Fire hazard
Sudden release of pressure hazard
Reactive Hazard
Complies
Complies
No
No
No
No
No
CWA (Clean Water Act)
This product does not contain any substances regulated as pollutants pursuant to the Clean Water Act (40 CFR 122.21 and 40
CFR 122.42)
CERCLA
This material, as supplied, does not contain any substances regulated as hazardous substances under the Comprehensive
Environmental Response Compensation and Liability Act (CERCLA) (40 CFR 302) or the Superfund Amendments and
Reauthorization Act (SARA) (40 CFR 355). There may be specific reporting requirements at the local, regional, or state level
pertaining to releases of this material
US State Regulations
California Proposition 65
This product has been evaluated and does not require warning labeling under California Proposition 65.
U.S. State Right-to-Know Regulations
Chemical Name New Jersey Massachusetts Pennsylvania
2-(2-ethoxyethoxy)ethanol
111-90-0
[2-(2-Methoxymethylethoxy)methyle
thoxy]-propanol
X - X
X - X
Page 7
640403 Ultra High Speed Floor Finish Revision Date 13-Mar-2017
_____________________________________________________________________________________________
25498-49-1
Zinc ammonium carbonate X - X
Magnesium Nitrate
10377-60-3
X X X
U.S. EPA Label Information
EPA Pesticide Registration Number
Not Applicable
16. OTHER INFORMATION
NFPA Health hazards 0 Flammability 0 Instability 0 Physical and Chemical
Properties Yes
HMIS Health hazards 0 Flammability 0 Physical hazards 0 Personal protection B
Issue Date
Revision Date
Revision Note
No Information available
Disclaimer
The information provided in this Safety Data Sheet is correct to the best of our knowledge, information and belief at the
date of its publication. The information given is designed only as a guidance for safe handling, use, processing, storage,
transportation, disposal and release and is not to be considered a warranty or quality specification. The information
relates only to the specific material designated and may not be valid for such material used in combination with any other
materials or in any process, unless specified in the text.
13-Mar-2017
13-Mar-2017
End of Safety Data Sheet
Loading...