Global411 MS41p1 Quick Installation Manual

Quick Installation Guide

For MS41p1

Contents Table

Contents Table ........................................................................................ 1

Chapter I Introduction .......................................................................... 2

1.1 Overview ............................................................................................................................. 2

1.2 Features ............................................................................................................................... 2

Chapter II Hardware setup ................................................................... 3

2.1 Interface & Indicator Light Introduction ............................................................................. 3

2.1.1 MODEM Indicator Light & Interface Introduction ............................................. 3

2.1.2 Interface of splitter ................................................................................................ 4

2.2 Package checking ................................................................................................................ 4

2.3 Layout ................................................................................................................................. 4

Chapter III Configuration Instructions ................................................ 5

3.1 Before Configuration: ......................................................................................................... 5

3.2 Instructions to Configure Router Through Web Interface ................................................... 5

3.2.1 Web Log-In ............................................................................................................ 5

3.2.2 WEB Interface Descriptions ................................................................................ 6

3.3 Instructions on the Application of Common-use Function Modules ................................... 7

3.3.1 Save & Reboot ...................................................................................................... 7

3.3.2 LAN Setting ........................................................................................................... 7

3.3.3 DHCP Setting ........................................................................................................ 8

3.3.4 User Management Setting .................................................................................. 8

Chapter IV Typical Application Cases .................................................. 9

4.1 Single-user Log-on (supported both by Modem version and Router version) .................... 9

4.1.1 Dialing Mode (Dynamic IP) ................................................................................. 9

4.1.2 Special Line Mode (Static IP) .............................................................................. 9

4.2 Multi-user Log-on (supported only by Router version via its router feature) ................... 10

4.2.1 Dialing Mode (Dynamic IP) ............................................................................... 10

4.2.2 Special Line Mode (Static IP) ............................................................................ 13

Chapter I Introduction

1.1 Overview

The MS41p1 supports ADSL, ADSL2 and ADSL2+ over the existing copper lines,

with downstream transmission rate up to 24Mbps (ADSL2+) and upstream transmission

rate up to 1.024 Mbps. They can support PPPoA (RFC 2364 - PPP over AAL5), PPPoE

(RFC 2516 – PPP over Ethernet) and RFC 1483 encapsulation over ATM (bridged or

routed).

1.2 Features

Standards Compliance

◆ ANSI T1.413 Issue 2 compliant

◆ ITU-T G.992.1 (G.DMT) compliant: Up to 8Mbps downstream and 896Kbps upstream

data rate

◆ ITU-T G.992.2 (G.lite) compliant: Supports splitter-less implementation and up to

1.5M downstream and 512Kbps upstream data rate

◆ ITU-T G.992.3 compliant: Better performance on long lines, and improve

interoperability between chipset suppliers

◆ ITU-T G.992.5 Annex A compliant: Up to 24Mbps downstream and 1Mbps up stream

data rate

◆ ITU-T G.992.5 Annex M compliant: Up to 24Mbps downstream and 3Mbps up stream

data rate.

Hardware Features

◆ Compatible with various local telecom equipments: Huawei, ZTE, DTT, Alcatel,

Lucent, Ericsson and so on.

◆ Stable transmission speed even at a transmission distance of 5KM

◆ Supports 8 PVCs

Software Features

◆ Supports RFC 1483 protocol (MPOA), RFC 1577 protocol (IPOA),RFC 2364 protocol

(PPP over ATM) ,and RFC 2516 protocol

◆ Firmware upgrade and configuration over WEB

Operating Environment

◆ Operating: ＋0 ~ ＋50

◆ Non-operating: －40 ~ ＋85

Humidity

◆ Operating: 10%~95% RH

◆ Non-operating: 10%~95% RH

Standard Approval

◆ CE CLASS B.

◆ FCC PART 15 CLASS B

◆ FCC PART 68

◆ UL 1950

Chapter II Hardware setup

2.1 Interface & Indicator Light Introduction

2.1.1 MODEM Indicator Light & Interface Introduction

Item

Indicator

Light

Interface

Introduction

Label

DSL

Internet

Ethernet

Power

DSL

Ethernet

State Introduction

ON：MODEM synchronized to the DSLAM

Flash: MODEM not synchronized

OFF: in Bridge mode or ADSL disconnected

ON: in Router mode and ADSL connected,

can transmit IP packets

ON： linked to network card of PC

ON：MODEM power on

Connect to the ADSL line or the ‘MODEM’

port of Splitter

Connect to the NIC with a crossed network

line

PWR

Reset Restore default settings

Connect to power adapter enclosed in the

package

Power switch

2.1.2 Interface of splitter

Label Introduction

LINE Connect to the ADSL line

MODEM Connect to ‘ADSL’ port of the MODEM

PHONE Connect to the phone

2.2 Package checking

First of all, please check out if the articles listed below present.

Item Quantity Remark

Power Adapter 1

Phone line 2

RJ45 Network Line 1

MODEM 1

Splitter 1

2.3 Layout

ADSL Line

Internet

DSLAM

MS41p1

Splitter

Telephone / Fax Machine

RJ-45 Cable connect to NIC

Note: Splitter is needed to: -Filter out line noise, i.e.

- Prevent line noise when there is incoming / outgoing call;

- Prevent connection speed drop when using modem.

Chapter III Configuration Instructions

This chapter introduces instructions on how to configure MS41p1 Router. All

the following instructions are aimed at Router version, please skip this chapter if

the product you purchased is Modem version in that Modem can be used directly

without further configuration.

3.1 Before Configuration:

Before installation of ADSL, please check the following facts with your brand-band

service provider:

(1) Internet Connection Mode

A．Static IP； B．PPPOE；C．PPPOA；

(2) If Static IP connection is adopted, the service provider needs to submit public

IP , subnet mask , gateway , and DNS .

(3) If PPPOE or PPPOA is adopted for connection, the service provider needs to

provide the info: username , password .

(4) Data encapsulation method:

A．LLC/SNAP B．VCMUX

(5) VPI= VCI=

(6) Debugging Code

A. T1.413 B. G.dmt C. G.lite

Note: The default is adaptation, which can negotiate and match the debug code of

the center automatically; thus no modification of setting is needed.

3.2 Instructions to Configure Router Through Web

Interface

Note: If the product you purchased is of Modem version, please use the device

directly without further configuration on ADSL.

3.2.1 Web Log-In

After the hardware installation, turn on the power to start. Please be sure your

computer can ping through the LAN port of ADSL(Default IP: 192.168.1.1), then start IE

software and type in http://192.168.1.1 on the address bar. Please enter username and

password after confirmation.