Page 1
This product may be purchased from Connevans Limited secure online store
at www.DeafEquipment.co.uk
DeafEquipment.co.uk
Solutions to improve the quality of life
SSoolluuttiioonnss ttoo iimmpprroovvee tthhee qquuaalliittyy ooff lliiffee
Connevans
Page 2
VIBRATION WATCH equipped
with:
Vibration Alarm won't disturb others.
Beep Alarm option
Auto Reload Countdown Timer
can be set for seconds, minutes &
hours. Use for reminders such as
medical conditions, medication,
timing presentations or
procedures, parking, cooking. Will
automatically reload to preset
countdown time.
Electo-Luminescent backlight
For viewing display at night
Second Clock great when
traveling in a different time zone.
Two Alarm Settings use for daily
reminders, wake up, snooze,
medication
Hourly Alert/Chime Option
12 or 24 Hour clock
Stopwatch
BEFORE YOU BEGIN
Press the MODE, START/STOP,
LAP/RESET buttons at the same
time and hold until display clears.
Release buttons. The clock time
will be at 12:00 A.M. with the
Alarms, Hourly Alert, Beeping
and Vibration functions not set.
The date will be January 1 and the
display will show M0
M0 for Monday.
M0M0
OPERATING MODES
Your watch has six operating
modes:
To go from one operating mode to
another, repeat pressing the
MODE button for each mode to be
displayed. The operating modes
will rotate in the order as listed
above.
TO BECOME FAMILIAR WITH
THE OPERATING MODES &
THEIR SYMBOLS, ROTATE
THROUGH EACH MODE BY
PRESSING THE ‘MODE”
BUTTON.
FIRST TIME SETTING OF
YOUR CALENDAR/CLOCK
(You must have this set for your
Alarm Settings to be accurate.)
When setting the Calendar &
Clock, the rotation for setting is
Seconds, Hour, Minutes, 12/24Hr,
Date, Month, Day of Week.
ONLY when the digits are
BLINKING
the setting. The clock will stop
blinking when no button is pressed
for two minutes. You cannot
switch to another mode of
operation while the display is
blinking. To exit and stop the
blinking, push LAP/RESET
button.
1. Repeat pressing the MODE
button until the (1) CALENDAR
CLOCK operating mode shows
on the display.
can you set or change
2. Press & Hold the LAP/RESET
button until the second’s digits
begin to BLINK.
Press the START/STOP button to
reset the second’s display to 00
3. Press the MODE button. The
hour digits will begin to BLINK.
Press the START/STOP button to
rotate to correct hour of the day.
WHEN IN THE 12 HR MODE, A
PM INDICATOR WILL APPEAR
ON THE DISPLAY ABOVE
AND LEFT OF THE HOUR
DIGITS. AS YOU ROTATE TO
12 HOURS THE PM MUST
SHOW FOR SETTING
CORRECT TIME FOR
AFTERNOON OR EVENING.
BE SURE TO SET CORRECTLY
FOR THE CURRENT TIME OF
DAY.
4. Press the MODE button to go
to the minute digits. The minute
digits will begin to BLINK.
Press the START/STOP button to
rotate to the correct minute.
5. Press the MODE button and the
12H
12H (12 Hour) mode will show
12H12H
and BLINK on the display. To
select the 24 Hour Mode, press the
START/STOP button once. 24H
will show on display.
6. Press the MODE button for the
date. The number 1111 will BLINK
at the top left corner of the
display. Press the START/STOP
button to rotate to the correct date
of the month. (1 - 31)
7. Press the MODE button for the
Month. The No. 1111 will BLINK on
the display. Press the
START/STOP button to rotate to
the current month of the year.
(Example; 6666 for June, 9999 for
September)
8. Press the MODE button for the
Day of the Week. M0
on the display. Press the
START/STOP button to rotate to
00.
0000
24H
24H24H
M0 will BLINK
M0M0
the correct day. (Example TU
Tuesday; TH
9. Press the LAP/RESET button
when you have finished the correct
set up. The display will stop
blinking.
HOW TO SET AN ALARM
CLOCK (Setting procedure is the
same for BOTH alarms)
1.Repeat Pressing the MODE
button to rotate to the alarm
operating mode you want: A1
1st ALARM or A2
ALARM.
2.Press & Hold the LAP/RESET
button until the hour digits
BLINK.
Press the START/STOP button to
rotate to the hour wanted.
Note: In the 12
remember to use the PM
for correct setting.
3.Press the MODE button to go to
the minutes. The minutes will
BLINK. Press the START/STOP
button to rotate to the minute
wanted.
4.Press the LAP/RESET Button
when finished. The display will
stop blinking. The set icon will
show on the display. Your alarm is
set.
When A1 Alarm is set the icon
shows bedside the PM
under the AAAA.
When A2
shows on the display beside the
A1
A1 icon.
A1A1
HOW TO TURN ON AND OFF
THE HOURLY ALERT
1. Repeat Pressing the MODE
button and select either 1st
ALARM=A1 or 2ND ALARM=A2
2. Repeat Pressing START/STOP
button until the Hourly Alert
indicator (located beside the Al 2
indicator) shows on the display.
Hourly alert is on when icon
TH for Thursday
THTH
A2 = 2ND
A2A2
12 Hr
Hr Mode,
1212
HrHr
PM indicator
PMPM
A2 Alarm is set the icon
A2A2
TU for
TUTU
A1 =
A1A1
PM indicator
PMPM
shows. Hourly alert is off when
icon doesn’t show.
ON/OFF SETTINGS OF
ALARMS
Note: To turn on or off First
Alarm you must
mode.
To turn on or off Second Alarm
you must be in the A2
Repeat Pressing the MODE button
to show alarm you wish to turn
off or on: 1ST OR 2ND
ALARM.
Repeat Pressing the START
/STOP button to rotate, alarm on
(hourly alert) & alarm off. When
Icon(s) shows, alarm is set. Alarm
is off when icon does not show.
(See previous illustration)
HOW TO ACTIVATE OR
DEACTIVATE VIBRATION
AND BEEP FUNCTION
1. Repeat Pressing the MODE
button to the CALENDAR
CLOCK mode.
2. Repeat Pressing the
START/STOP button to rotate
through the selection of settings.
When a function is activated, its
respective icon will be
highlighted, at the top right corner
of the display. Rotation will be:
Vibration ON, Beep ON,
Vibration and Beep ON, Vibration
& Beep OFF. Select one of the
four functions that you desire.
This can be changed at anytime by
following steps 1 and 2.
Alarm will stop automatically
after approximately 20 seconds.
To stop alarm before the
be in the A1
A1
A1A1
A2 mode.
A2A2
Page 3
automatic stop, press any button.
GLOBAL
NOTE: To check setting the watch
is in at any time, press the MODE
button. With each press of the
button the vibration and/or beep
will respond if set.
HOW TO USE THE
COUNTDOWN TIMER
1. Repeat Pressing the MODE
button to display TR
(COUNTDOWN TIMER)
operating mode.
2. Press & Hold the LAP/RESET
Button until the Seconds digits
BLINK. Press the START/STOP
button to set to the seconds
wanted. You can select from 0 to
59 seconds. If you do not wish to
set the seconds, go to #3 below.
3. Press the MODE Button to go
to the hours. The hour digits will
BLINK. Press the START/STOP
button to set the number of hours
wanted. You can select from 0000 to
23
23 hours.
2323
4. Press the MODE Button to go
to the minutes. The minute digits
will BLINK. Press the
START/STOP button to set the
number of minutes wanted. You
can select from 0000 to 59
5. Press LAP/RESET button when
you have finished. The display
will stop blinking.
To reset the Countdown Timer
for a different time see "How to
Use the Countdown Timer" and
follow instructions.
TO START THE
COUNTDOWN TIMER,
Press the START/STOP button
(after the countdown timer is set).
The timer will start to countdown.
To interrupt, press the
START/STOP button. Pressing
the START/STOP button again
will start the countdown from
where it last left off.
TR
TRTR
59 minutes.
5959
Note: When Countdown Timer is
set for more than ten minutes, a
short single reminder will advise
you of 10 minutes remaining and
then at 5 minutes remaining.
AUTO RELOAD
COUNTDOWN TIMER will
automatically reload for the time
preset, when the timer reaches “0000”
If you do not wish to start the
countdown again immediately,
press the START/ STOP button
twice, if alarm is activated. Press
once to stop the countdown if
alarm is not activated.
To restart the preset countdown at
any time, press the START/STOP
button while in the
COUNTDOWN - TR
TO USE THE REPEATABLE
COUNTDOWN TIMER WITH
PAUSES INBETWEEN
When the auto-repeat countdown
timer reaches zero it automatically
alarms and starts to countdown
again for the preset time. You can
cancel the countdown and return
to the original countdown time.
To reset to the original countdown
time PUSH the LAP/RESET
button and HOLD IT for
approximately 2 to 3 seconds.
Digits will flash showing the
amount of time that the countdown
was set for originally.
Push the LAP/RESET button
once, and the digits will stop
flashing. (If you do not push the
LAP/RESET button to stop the
flashing, the digits will stop
flashing automatically after 2
minutes.)
To activate the start of the
countdown when you need it, push
the START/STOP button once.
HOW TO USE THE
STOPWATCH
TR mode.
TRTR
1. Repeat Pressing the MODE
button to show STOPWATCH on
the display.
2. To start the Stopwatch, press
the START/STOP button. The
Stopwatch will start keeping time
and the Icon (symbol at the top of
the display) will flicker to show
the action.
TO STOP THE STOPWATCH,
press the START/STOP button.
Pressing the START/STOP button
again will start the stopwatch
running from where it last left off.
The Stopwatch can count up to 23
hours, 59
59 minutes and 59
5959
seconds. Each hour accumulated
shows at the top left of the display.
To RESET the stopwatch to zeros,
press the LAP/RESET button,
when it is in a stop position.
Split Timing on Stopwatch
1. Start the Stopwatch by pressing
the START/STOP button. The
stopwatch will start keeping time.
2. Press the LAP/RESET button.
The watch will continue counting
the time even though you do not
see it on the display. The Icon at
the top of the display will continue
to flicker to show action and that
counting continues.
3. Press the LAP/RESET button
again and the display will change
and show the time that has
accumulated in total.
4. To RESET the Stopwatch,
press the START/STOP button
and then press the LAP/RESET
button.
HOW TO SET THE SECOND
CLOCK
1. Repeat Pressing the MODE
button to show SECOND
CLOCK (T2)
2. Press & Hold the LAP/RESET
button until the Hours digits
BLINK.
(T2)
(T2)(T2)
59.99
5959
99
9999
23
2323
3. Press the START/STOP button
to rotate to the hour you wish to
set. (In 12
12 Hr Mode, use PM
1212
indicator for correct setting of
afternoon or evening.)
4. Press the LAP/RESET button
when desired hour has been set.
NOTE: Only the hour can be set in
second clock mode. (The minutes
and seconds will be the same as
the Calendar Clock)
HOW TO USE THE EL BACK
LIGHT
Press the LIGHT button to light up
the LCD display at any time. The
screen will be lit for
approximately 3 seconds before
going off automatically.
The EL back light will flash when
an alarm is activated
BATTERY INFORMATION
Your watch uses a Standard 3 volt
lithium CR2032 or equivalent
battery. Battery life will vary due
to how often the EL back light and
vibration function are used.
Batteries should be replaced by a
qualified person to maintain water
resistance.
DISCLAIMER
GLOBAL does not accept any
responsibility what so ever for
any inconvenience or noncompliance for medication or
any other reminder the watch
may be used for.
SERVICE
This unit should be serviced by
qualified service personnel. The
user should not attempt to service
the unit.
Servicing should be referred to:
Global Assistive Devices, Inc.
4950 North Dixie Highway,
Fort Lauderdale FL USA 33334
PM
PMPM
Before sending your unit for
service, have the battery checked
and/or try resetting by pressing the
MODE, START/STOP and
LAP/RESET buttons at the same
time and hold until the display
clears.
ONE YEAR LIMITED
WARRANTY
Your VibraLITE 3 is warranted to
be free from defects in material or
workmanship for One Year from
the date of purchase.
This is a limited warranty and
covers watch functions only. This
warranty does not apply to the
battery, band or to any unit which
has been subject to misuse,
negligence or accident. This
warranty is void if the watch has
been tampered with, altered, or
repaired other than by a qualified
service center. At its option,
GLOBAL ASSISTIVE
DEVICES, INC. may select to
replace the unit, rather than repair
it. During the warranty period,
return the watch, with dated proof
of purchase, in a secure package,
insured and with shipping charges
prepaid. No C.O.D. packages will
be accepted. Please include a note
describing the service required and
include $8.50 (check, money
order, Visa, MasterCard,
American Express, or Discover)
for shipping and handling in the
USA. Other Countries please
contact us for pricing.
Copyright:
ASSISTIVE DEVICES, INC.
4950 North Dixie Highway
Fort Lauderdale Florida USA
33334-3947
Page 4
QUICK REFERENCE Model VL300
SELECTION OF VIBRATION, BEEP, BOTH OR OFF SIGNAL (S)
Press MODE button until the CALENDAR CLOCK mode shows on the display. Repeat pressing
START/STOP button to select desired function. Icon(s) at top right of display will indicate function:
Vibration, Beep, Both or Off.
A Quick Check to see what function is set, is to push the MODE button while in the Calendar Clock
mode. The function that is set will respond each time you push the MODE button.
SETTING OF ALARMS AND COUNTDOWN TIMER
Press MODE button to rotate to the mode you wish to set. (TR for COUNTDOWN TIMER; A1 or A2
for ALARMS) Press and Hold LAP/RESET button until the digits blink. While digits blink, press the
START/ STOP button to advance the blinking function to the time wanted. Press the MODE button
to change from hours to minutes and advance the time by pushing START/STOP button.
For alarm
settings, hour(s) and /or minute(s) can be set. For countdown timer, seconds and/or hour(s) and
minute(s) can be set
. Press the LAP/RESET button when completed. (Digits will stop blinking) In the
Alarm(s) mode, the alarm indicator icon shows which alarm is activated.
To reset Alarms & Countdown Timer for a different time, repeat instructions as above.
AUTO RELOAD COUNTDOWN TIMER
When the countdown timer reaches "0", it will automatically reload for the time that was preset. If
you do not wish to start the countdown again immediately, press the START/ STOP button twice, if
the alarm is activated. Press once to stop the countdown if the alarm is not currently activated. To
restart the preset countdown at any time, press the START/STOP button while in the TR
(COUNTDOWN) mode.
HOURLY ALERT SETTING
Press the MODE button until display is in an ALARM Mode. (A1 or A2) Repeat pressing the
START/STOP button until the Hourly Chime icon shows. (Located beside the A2 icon)
Copyright:
Global
Assistive Devi ces , Inc.
Fort Lauderdale Fl or i da U S A
Loading...