Global 900E User Manual

Page 1
900E
Vehicle GPS Tracker
User Manual
2009-10-01
www.globaltrackergps.com
Page 2
1. Working Directions..........................................3
2. GPS Tracker Installation..................................3
2.1. Product Parts List ........................................3
2.2. Precaution before Installation …...................5
2.3. Installation....................................................5
2.4. Wiring Description.........................................6
3. Operating Instructions .....................................7
4. SMS Tracking by Mobile....................................8
4.1. Position Report Function................................9
4.2. Tracking Function..........................................9
4.3. Stop tracking function....................................9
5. GPRS Tracking by computer...........................10
5.1.Set APN........................................................10
5.1.Set IP and Port..............................................10
6. Take Photo function........................................10
6.1. Take photos.................................................10
6.2.Takephotos by press SOS button..................10
6.3. Set the time interval to take photos..............10
7. LCD Screen………...........................................11
7.1. Use as navigation.........................................11
7.2. Make and receive phone calls. .....................11
7.3. 7.3.Receive massages from control center...11
7.4. Receive GPS signal.......................................11
7.5. Fuel Sensor …...............................................11
www.globaltrackergps.com
Page 3
1. Working Directions
Thank you for your purchase of 900E Vehicle GPS Tracker. In order to realize the full functions of this product, please read this manual carefully before starting to use the product.
1 This product can only be maintained and repaired by qualified
professional service personnel. If you detach this product for maintenance or repair, your warranty will be invalidated.
2 When connecting the other devices, read carefully their instruction
manuals, so as to carry out correct installation; do not connect incompatible device.
3 Please use genuine original parts and qualified batteries and
peripheral equipments, so as to avoid damage to this product.
4 As this product is a high-tech product, please read carefully this
manual before starting to use the product, so as to avoid inappropriate operation.
5 Drivers should not operate this product while driving a vehicle,
thereby, affecting safe driving.
6 This product can work properly only when GSM communication is in
good condition.
7 Please reduce electromagnetic wave interference to the product; and
use it properly.
8 GPS communication is liable to be affected by environmental
shielding; may fail to carry out positioning during certain circumstances. It will resume the positioning function as soon as it leaves the shielding environment. This is normal. Please do not worry when encountering such problem.
9 Each signal sent out from the system will be confirmed for
successful transmission in the base station of the mobile operator. However, if system stoppage occurs or if the mobile telephone is preset to a switch off state by the customer, it cannot ensure successful transmission.
10 For safety reason, do not tell the other people your 900E mobile
number, without taking precautions. Otherwise, your privacy may be compromised along with other safety problem.
2. Wiring Installation
2.1. Product Parts List
www.globaltrackergps.com
Page 4
GPS Tracker Unit
GPS Antenna
GSM Antenna
Car Charger Lighter Socket
www.globaltrackergps.com
Page 5
2.2. Precaution before Installation
1 Check if all the parts are included.
2 Prepare a SIM card for GSM communication. Use some other mobile
phone to confirm that the PIN code has not been set and that it can dial out and receive telephone calls and SMS without problem.
3 Before install the SIM card; make sure to cut off power from the GPS
Tracker unit. The correct installation method is to push the tray completely into the GPS Tracker unit, until you feel it is hooked by something.
4 Find a suitable place inside the car for installing the unit.
5 Check if all the wiring has been connected correctly; then connect
the GPS Tracker unit to the power source.
2.3. INSTALLATION.
2.3.1 Step 1: Install SIM Card
1 Using a speculate object to poke the small button of the SIM card
seat, and then it will pop-up a small drawer.
2 Put the SIM card in the drawer, and put back the drawer, as
direction shown in the picture.
3 Make sure to turn off the power before install the SIM card.
4 Make sure to deactivate the PIN code, so that the SIM card can
operate without PIN protection.
5 Before install the SIM card to the GPS Tracker, please use a mobile
phone to make sure the SIM card can make & receive phone calls without problem.
6 Before install the SIM card to the GPS Tracker, please use a mobile
phone to empty the SMS storage of the SIM card.
2.3.2 Step 2: Connect GSM Antenna.
1 Connect the GSM Antenna to the unit.
2 Fasten the connection by turning the screw in the bottom.
3 Please do not swing round the antenna itself.
2.3.3 Step 3: Connect GPS Antenna.
1 GPS antenna is used to receive satellite signals in the sky. It
should be positioned at a place where it will have an unobstructed view of the sky. The ideal location is top of the dashboard or close to the rear window of the car.
2 GPS antenna can pick up signals through glass and plastic, but will
not "see the sky" through metal or other conductive surfaces. To avoid distractions of GPS signal, make sure the antenna is not covered or shielded by any object containing metal, such as the metallic windshield.
www.globaltrackergps.com
Page 6
3 If your car is with metallic windshield please cut a hole on the
windshield above the place where you put the GPS antenna, so that the antenna can receive the GPS signals.
2.3.4 Step 4: Connect power charging.
900E connects to the 4pin and 6pin wires.
2.4. Wiring Description.
4 pins connector
Pin Color function
1 Red Power switch
2 Red Power switch
3 Yellow Connect to door sensor
4 Green Undefined input. (*)
(*) for example you can use it to detect the signal of car alarm.
6 Pins Connector.
Pin Color function.
1 Red DC in Input voltage: 8-40V
Suggestion: 12V
2 Black GND
3 Brown Output Starter kill relay you
can use it to cut the electricity or oil of the car
4 White SOS button
5 Green Output Starter kill relay you
can use it to cut the electricity or oil of the car
6 Blue ACC Signal detecting
According to the relay parameter to make sure to following requirement: The input voltage of relay must be suited to the car battery
www.globaltrackergps.com
Page 7
3. Operating Instructions.
SMS protocol of 900E, the default password of 900E is 000000
SMS Instruction Format Remark
1 Request one position A******,000
000: command code
******: password, default 000000
2 Modify user password A******,001,######
001: command code
******: old password , default 000000 ######: new password
3 Set a preset phone number for SOS
button or monitoring number
A******,002,1, Tel Number A******,002,2, Tel
Set SOS number Set monitoring number
4 Set the time interval of
position refresh to SOS number
A******,003,XXX
XXX =000,stop
XXX = 001 – 999 time internal (unit: min)
5 Set low power alarm When the 900E
voltage is lower than the preset value, 900E will send one lower power alarm SMS to the control number. Otherwise,there is not this function in vehicle tracker.
A******,004,X X : voltage preset value
X=0, close (default ) X =1, <3.5V send SMS alarm X =2, <3.6V send SMS alarm X =3, <3.7V send SMS alarm X =4, <3.8V send SMS alarm X =5, <3.9V send SMS alarm
6 Set over speed alarm When the
900E speed higher than the preset value, 900E will send one over speed alarm SMS to the control
A******,005,XX XX : the speed preset value
XX = 00 , close 01 = XX = 99 (unit: XX Km/h)
7 GPRS Status, To
check GPRS Status
A******,502 502: command code
8 Get IMEI A******,505
9 Set GPRS internal of position refresh A******,506,00030 00030: Such as 30 seconds interval is
00030
10 Check GPRS internal of position
refresh
A******,507
11 Inquire GPRS parameter Retrue
Including IP, Port, APN
A******,006
12 Control the output A******,007,P,F
P: the position of the output
P =1 output 1 P =2 output 2
www.globaltrackergps.com
Page 8
F: the control signal
F =1 give the relay the current to drive it (cut off the car power). F =0 cut off the current of the relay (comeback the normal).
13 Time zone setting A******,008,-x X= -4
x= -3
14 Inquire the system parameter.
Including the software version, password, interval, speed limit, area limit, I/O state, GPS state, SOS number, control number, etc
A******,009
15 GPRS switch A******,010,X X: GPRS function
=0 GPRS OFF =1 GPRS UDP =2 GPRS TCP
16 SET APN A******,011,APN,
username,password
APN: GPRS use this gateway to connect internet. Username: APN Username Password: APN Password The default APN is CMNET
17 Set the center IP and Port Set the
server parameter.
A******,012,IP,Port IP: Platform server ip
Port: Platform server port
18 LED Light Switch A******,666, X X: LED Light Switch
X =0 LED Light OFF X =1 LED Light ON
19 Photos take interval A******,503,XX Xx= time interval (10 min.)
xx=01 (10 min) xx=02 (20 min) ...
20 Check fuel sensor ADC A******,201
21 Set fuel Sensor A******,202,XXXX,YYYY XXXX=MAX. FUEL SENSOR
YYYY=MIN. FUEL SENSOR
22 Inquire Max and Min ADC fuel
sensor
A******,203
23 Reset to factory settings A******,888
24 Restart Tracker A******,999
4. SMS Tracking by Mobile.
4.1. Position Report Function
4.1.1. Get position from vehicle -way 1:
No matter where you are, when you want to know the position of your vehicle.
Step1 Send a SMS message or make a telephone call to the 900E.
Step2 vehicle will report its location back to you by SMS, which
including the position information
Edit a message as following format, and then send it to 900E: Command Remark
www.globaltrackergps.com
Page 9
Send Format: A+Password+,+000 Get position command code is: 000 For Example Send message: A000000,000 000: command code 000000: password, default 000000 Back information: Lat:2232.6022N, Lon:11402.2969E This mean your position is on North Latitude 22 degree 32.2232 cent and East Longitude 114 degree
2.2969 cent
4.1.2. Get position from vehicle -way 2:
Apply for one position service by another way: you need pre-storage the phone number in SIM card:
Step1 Make a cell phone call to 900E
Step2 After listening the ring of 900E, it will hold off after two
rings.
Step3 Then, after 10 second, the cell phone will receive the Position
SMS. (Its means is 900E will send Position Data every 5 minute.)
4.2. Tracking Function
Tracking report function can be turned on or off according to the requirements of the user. Tracking function will continually report vehicle position until it get stop command .In this tracking mode, 900E will send one position message at a preset time interval.
Step1. Edit a message as following format, then send it to 900E Command Remark Send Format: A+Password+,+003,+XXX Note: XXX , if XXX=000 it is STOP tracking Unit: preset minute interval Command code : 003 For example: A000000,003,003 003: command code 000000: password, default 000000 003: 3 minute interval It means is 900E will send Position Data every 3 minute.
Step2. 900E will send back one SMS-----Set Time OK. This SMS means that 900E is in tracking mode now and preset time interval is 3 minutes.
Step3. 900E will send back position SMS at preset time interval. In this example, the SMS will send back at preset time interval: 3 minute
4.3. Stop tracking function.
This function is used to turn off tracking report function. Edit a message as following format, and then send it to 900E: Command Remark Command format: A+passwaord+,+003+,+000 For example: A000000,003,000 003: command code 000000: password, default 000: 0 minute interval, mean stop back
www.globaltrackergps.com
Page 10
5. GPRS Tracking by Computer.
The default mode is GPRS when powering on the unit. If you want to use the GPRS functions of the 900E, Send SMS to set APN and IP, Port.
5.1.Set APN.
Send the SMS to the tracker as following format Command Remark Command format: A+Password+,+011,+APN For example: A000000,011,CMNET 011 : Command code 000000: password, default 000000 CMNET: APN, is gateway to connect internet, Each country is different,
5.2.Set IP and Port.
Send the SMS to the tracker as following format: Command Remark Command format: A+Password+,+012,+IP:Port For example: A000000, 012,119.147.24.211:8886 012 : Command code 000000: password, default 000000
119.147.24.211 Platform server IP 8886: Platform server software Port When the 900E connect to the monitor system, the power LED flash by 1 S. Then you can login in the tracking server to manage your car.
6. Take Photo function (only for 900E): Connect the Camera to 900E,You can send a command to take photographs; the car terminal will shoot pictures and spread to Center. After that, pictures will display on the operation platform.
6.1. Take photos on software.
6.2. Take photos by press SOS button.
6.3. Send SMS command to set the time interval to take photos.
Such as 30 minutes to take a photo and send back to software. For exemple: A000000,503,01 (01= photos interval 10 min.)
www.globaltrackergps.com
Page 11
7. LCD Screen (only for 900E):
7.1. Use as navigation.
7.2. Make and receive phone calls.
7.3. Receive massages from control center.
7.4. Receive GPS signal.
7.5. Fuel Sensor.
Open http://www.globaltrackergps.com/ to begin tracking.
www.globaltrackergps.com
Loading...