THE NAME AND FUTURE OF
CAMERA STABILIZATION
TM
Operating Instructions
Operating Instructions
GLIDECAM HD7
GLIDECAM HD7
Digital Monitor
Digital Monitor
(LCD Multi Format)
(LCD Multi Format)
Model : GLIDECAM HD7
IMPORTANT SAFETY INSTRUCTIONS
1. Please read this manual thoroughly before operating the monitor.
2. Unplug monitor from the wall outlet before cleaning the LCD screen. Do not use liquid cleaners or
aerosol cleaners. Use ONLY a damp cloth provided.
3. Don’t use any unauthorized accessories not recommended by the manufacturer as they may cause
hazards.
4. Don’t operate this monitor near damp or wet surfaces.
5. Use only the recommend manufacturer mounting hardware accessories. Slots and openings in
the cabinet and the back or bottom are provided for ventilation, and to insure reliable operation of
themonitor and to protect it from overheating, these openings must not be blocked or covered.
PORTABLE CART WARNING
(symbol provided by RETAC)
6. This appliance should be operated only from the type of power source indicated on the marking label.
If you are not sure of the type of power supplied to your home, consult your dealer or local power
company. For appliance designed to operate from battery power, refer to the operating instructions.
7. This appliance system is equipped with a 3-wire grounding type plug (a plug having a third
(grounding) pin).
This plug will only fit into a grounding-type power outlet. This is a Safety feature.
If you are unable to insert the plug into the outlet, contact your electrician to replace your outlet. Do
not ignore the Safety purpose of the grounding plug.
8. For added protection for this product during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the
product due to lightning and power-line surges.
9. Do not allow anything to rest on the power cord.
10. Follow all warnings and instructions marked on the appliance.
11. Do not overload wall outlets and extension cords as this can result in fire or electric shock.
12. Do not attempt to service this monitor without a qualified service personnel.
FCC NOTICE
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
To assure continued compliance, follow the attached installation instruction and do not make any
unauthorized modifications.
Note:
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
The user may find the booklet “Something About Interference” available from FCC local regional offices
helpful.
Warning:
To assure continued FCC emission limit compliance, the user must use only shielded interface cables when
connecting to host computer or peripheral devices. Also, any unauthorized changes or modifications to this
equipment could void the user’s authority to operate this device.
SAFETY PRECAUTIONS
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to alert
the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
THIS EQUIPEMNT MUST BE GROUNDED
To ensure safety operation, the three-pin plug must
be inserted only into a standard three-pin power
outlet which is effectively grounded through normal
household wiring. Extension cords used with the
equipment must have three cores and be correctly
wired to provide connection to the ground. Wrongly
wired extension cords are a major cause of fatalities.
The fact that the equipment operates satisfactorily
does not imply that the power outlet is grounded or
that the installation is completely safe.
For your Safety, if you are in any doubt about the
effective grounding of the power outlet, please
consult a qualified electrician.
CAUTION:
THE AC RECEPTACLE (MAINS SOCKET
OUTLET) SHALL BE INSTALLED NEAR THE
EQUIPMENT AND SHALL BE EASILY
ACCESSIBLE.
TO COMPLETELY DISCONNECT THIS
EQUIPMENT FROM THE AC MAINS,
DISCONNECT THE POWER CORD PLUG FROM
THE AC RECEPTACLE.
WARNING:
- TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOISTURE.
- TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD, KEEP THIS EQUIPMENT AWAY
FROM ALL LIQUIDS. USE AND STORE ONLY
IN LOCATIONS WHICH ARE NOT EXPOSED
TO THE RISK OF DRIPPING OR SPLASHING
LIQUIDS, AND DO NOT PLACE ANY LIQUID
CONTAINERS ON TOP OF THE EQUIPMENT.
CAUTION:
In order to maintain adequate ventilation, do not
install or place this unit in a bookcase, built-in
cabinet or any other confined space. To prevent risk
of electric shock or fire hazard due to overheating,
ensure that curtains and any other materials do not
obstruct the ventilation.
CAUTION:
TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD AND ANNOYING INTERFERENCE, USE
THE RECOMMENDED ACCESSORIES ONLY.
CAUTION:
This apparatus can be operated at a voltage in the
range of 100-240 V AC.
Voltage other than 120V are not intended for U.S.A
and Canada.
CAUTION:
Operation at a voltage other than 120V AC may
require the use of a different AC plug. Please
contact either a local service center for assistance
in selecting an alternate AC plug.
Notice (U.S.A. only):
This product has a fluorescent lamp that contains a
small amount of mercury. It also contains lead in
some components. Disposal of these materials may
be regulated in your community due to
environmental considerations. For disposal or
recycling information please contact your local
authorities, or the Electronics Industries Alliance:
http://www.eiae.org.
Information on Disposal for Users of Waste Electrical & Electronic Equipment
(private households)
This symbol on the products and/or accompanying documents means that used
electrical and electronic products should not be mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to designated
collection points, where they will be accepted on a free of charge basis. Alternatively, in
some countries you may be able to return your products to your local retailer upon the
purchase of an equivalent new product.
Disposing of this product correctly will help to save valuable resources and prevent any potential
negative effects on human health and the environment which could otherwise arise from
inappropriate waste handling. Please contact your local authority for further details of your nearest
designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national
legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for
further information.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the
correct method of disposal.
CE NOTICE
This is Class B product. In a domestic environment this may cause radio
interference in which case the user may be required to take adequate measures.
The apparatus shall not be exposed to dripping or splashing and no objects filled
with liquids, such as vases, shall be placed on the apparatus.
Thank you for purchasing this product, please read this instructions
carefully and save this manual for later use
Contents
1. Out Line • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 7
2. Features and Function • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 7
3.Controls and Functions • • • • • • • • • • • • • • • • • • • • • • 9
3 - 1. Front Panel • • • • • • • • • • • • • • • • • • • • • • • • • • 9
3 -2. Rear Panel • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 12
3 -3. Tally & Audio • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 14
3 - 4. Front F1, F2, F3, F4의 Function • • • • • • • • • • • • • • • • • • • • 15
4. STATUS DISPLAY • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 16
5. INPUT SELECT Button • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 17
6. OSD Menu • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 18
6-1. VIDEO Setup • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 19
6 -1-1. VIDEO(PC-RGB) Setup • • • • • • • • • • • • • • • • • • • • • • • • • • 20
6 -2. DISPLAY Setup • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 21
6 -2-1. DISPLAY (PC-RGB) Setup • • • • • • • • • • • • • • • • • • • • • • • • • • • 23
6 -3. COLOR Setup • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 24
6-4. MARKER Setup• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 25
6-5. OSD Setup • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 27
6- 7. GPI Setup • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 29
6 -8. SYSTEM Setup• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 30
7. Program Update Port • • • • • • • • • • • • • • • • • • • • • • • 31
7 - 1. Program Update Port(RJ- 11) • • • • • • • • • • • • • • • • • • • 31
7 - 2. Multi Monitor Control• • • • • • • • • • • • • • • • • • • • • • • 31
8. Remote Terminal Assignment • • • • • • • • • • • • • • • • • • • • • • • • • • 32
8 - 1. Remote Terminal(RJ-45) Assignment • • • • • • • • • • • • • • • • • • 32
8 - 2. GPI Port (RJ- 45) • • • • • • • • • • • • • • • • • • • • • • • 32
8 - 3. Remote Terminal Assignment (GPI Port)• • • • • • • • • • • • • • • • • 33
9. List of Compatible Signal formats • • • • • • • • • • • • • • • • • • • • • • • 34
9 - 1. Computer Signals (PC- RGB/DVI) • • • • • • • • • • • • • • • • 35
10. Specifications • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 36
11.DIMENSION • • • • • • • • • • • • • • • • • • • • • • • • • • 37
12.Trouble shooting • • • • • • • • • • • • • • • • • • • • • 38
13.Maintenance • • • • • • • • • • • • • • • • • • • • • • • 39
1. Outline
Glidecam HD7 HD Digital Monitor series are a Multi-Format HD Monitors with high core technology to
display various kind of digital video input signals. It supports HD/SD-SDI,
Composite/YC/YPbPr/RGB/DVI/PC-RGB/HDMI(HDCP) Signals.
2. Features
▪ Diagonal Line Compensation by MADI (Motion Adaptive
De-interlace) and LADI (Low Angle Diagonal Interpolation)
▪ High Speed Response
▪ Available Color Calibration
▪ HD 2K Format/ Multi format HD/SD-SDI Input
▪ 1ch HD/SD-SDI Inputs & 1ch Active Thru-out
▪ Analog Component & DVI Input
▪ Pixel to Pixel Display
▪ De-embedded 8 ~ 16ch Audio Level Meter
▪ Various Markers Display (EBU, Variable)
▪ PAP, H/V Delay, Blue/Mono etc Precision Monitoring
▪ Closed Caption (608 ANC, 608 Line21, 608 Transcoded, 708) Display
▪ Input Mode & Status Display
▪ Anamorphic Mode Display
▪ Time Code Display
▪ Waveform Monitoring Display (Y, Pb, Pr Selected)
▪ Vector Scope Display
▪ Remote GPI Control (RJ-45)
▪ Serial Control Port (Update & Control), (RJ-11)
▪ Built-In Speaker & Ear Phone Jack (Option)
▪ Analog Audio Input / De-embedded Output (Option)
▪ Built-In Audio Ear-Phone Jack (Option)
▪ TALLY Lamp
▪ Easy Control OSD MENU
▪ Source ID Name Display
▪ Lock Type Picture Adjustment
(Bright, Contrast, Phase, Chroma, Sharpness)
▪ Rack & VESA Mount (Rack Mount Option)
▪ Battery Pack V- Mount
3. Controls and Functions
3-1. Front Panel
BRIGHT : Adjusts Brightness
CONTRAST : Adjusts Contrast
CHROMA : Adjusts Chroma
PHASE : Adjusts Phase
VOLUME : Adjusts Volume
① STANDBY
Power On/Off button.
② SDI
SDI Input Select button
So use the Knob button you have to push one
③ INPUT
Analog input select button
(CVBS1, CVBS2, CVBS3, S-VIDEO(Y/C), YPbPr, RGB, PC-RGB(VGA), DVI)
④ SCAN
Scan mode select button
( Zero, Under, Over, Zoom Scan, Pixel to Pixel)
In the Pixel to Pixel mode you can choice the displayed area by (▲)Up button
⑤ BLUE/GRAY
⑥ W-FORM/VECTOR
Wave from and Vector scope display.
This function is available under SDI, CVBS, S-Video, YPbPr, RGB Mode
⑦ ⑧ ⑨ ⑩ FUNCTION 1 (F1, F2, F3, F4)
These four Function buttons carries out the item selected in the
SYSTEM Menu.
MENU
OSD MENU Activate button.
MARKER (▼)
When the OSD MENU is deactivated used for MARKER On/Off button.
When the OSD MENU is activated used for Down(▼) button.
⑬ DAYLIGHT(▲)
When the OSD MENU is deactivated used for display mode select.
There are three display mode and when you push this button the brightness be increased.
When the OSD MENU is activated used for UP ▲.
ENTER/STATUS
- When you control the menu used for Enter button.
Please refer to category 6 in detail .
- When the OSD MENU is deactivated used for input signal information display.
3-2. Rear Panel
SDI 1 , SDI 2 input terminal (BNC)
SDI Active selected loop OUT (BNC)
CVBS (Composite) 1, 2, 3 / Y, Pr, Pb / G, R, B / S-Y,S-C input terminal (BNC)
⑥ DVI-I / PC-RGB
For the PC-RGB(VGA) you can use DVI to VGA Gender
⑦ REMOTE Port ,RJ-45 Jack –Through (RJ-45)->
Terminal for controlling the monitor by an external control. (Make /Trig Type)
Please refer to category 8. Remote Terminal Assignment for detailed information.
⑧ UPDATE Port (RJ-11 Jack) : Serial Communication Port
This port is used to modify monitor program or to control Monitor. Please refer to category 7 for
detailed information.
⑨ ⑩ Audio Input / Output
⑪ Speaker .
⑫ Built in V-Mount for V pack battery
⑬ DC input
DC Adaptor : 12V
Battery : 11~20V
3-3. Tally & Audio
1) Tally
2) audio In/ Out
3-4. Front F1, F2, F3, F4 Function
Used to select the functions to be assigned to individual buttons F1,F2,F3 and F4 (front-panel buttons)
Available assigned Functions
- Audio Display On/Off
- Blue Only-Grayscale On/Off
- H/V Delay On/Off
- PaP On/Off
- Audio Mute On/Off
- Video Loss Tally On/Off
- Video Loss Alarm On/Off
- V Flip On/Off
- H Flip On/Off
- Freeze On/Off
- Time Code Display
- Waveform Display
- 1 : 1 Scan
- Aspect
- Anamorphic On/Off
Note :
When the input modes are DVI, PC-RGB signal, the following functions
are not available :
1) H/V Delay
2) Gray (MONO)
3) MARKER
4. STATUS DISPLAY
1) Audio Level Meter Display
Set “ON/OFF” and “ Position” from the Audio Level Display Menu.
On : Left (even channel), Right (odd channel), OFF : Hide Level Bar
Level Meter Position: Position audio display at the top or bottom of the screen.
2) Waveform Monitor / Vector Scope Display
W-FORM / VECTOR Position : Selectable the displayed position among
Set “ON/OFF” and “Position” from the W-FORM/VECTOR Button
WFM/Vector Position : Position Waveform/Vector from Display Menu
( Left Top, Right Top, Left Bottom, Right Bottom)
( These functions are available only in SDI, CVBS, S-Video, YPbPr Mode).
5. INPUT SELECT Button
SDI button : You can select SDI 1 or SDI 2 input.
Input button : You can select Analog input. (Component, CVBS 1.2.3, DVI, RGB)
When Menu control is not ON, if user press Enter button, then currently selected input information appears.
• When changing the input signal, there is a possibility that the signal will not be detected, or the mode
indication may be incorrect, or the screen size may be displayed incorrectly.
6. OSD MENU Control
1. Press “MENU” button for OSD Display.
2. Press “ENTER” button after menu selection by using UP ▲ / DOWN ▼ buttons
3. Adjust status on the selected item with ENTER and UP ▲ / DOWN ▼ buttons
4. Move to previous menu by using MENU button.
5. Close the OSD screen by pressing MENU continuously.
If there is no input signal or no detected signal, the menu might be erased.
If you set the menu with an unstable signal status, it may cause an error..
The MENU setting value depend on the input signal mode. Therefore, please check the
input mode at the bottom of the menu when changing settings.
6-1. VIDEO Setup
6-1. VIDEO Setup
▪ Brightness : Adjusts brightness
▪ Contrast : Adjusts contrast
▪ Chroma : Adjusts chroma
▪ Phase : Adjusts phase
▪ Sharpness : Adjusts sharpness
(This function can be controlled by VR control Knob attached in the front panel.)
Note : In PC-RGB Input Mode,
▪ RGB Color Set :Controls RGB Level in YPbPr,RGB,PC-RGB input mode. Select Default or User Adjust
▪ NTSC Setup : Selects 0 IRE,7.5 IRE 7.5IRE -> Operates at NTSC or YUV Mode
▪ Fast Mode
Used to decrease the afterimage when the input signal format is ‘i” (Intelace) and there are many
motion.
6-1-1. VIDEO (PC-RGB Mode) Setup
This Menu is displayed when selecting Auto Color Adjust as User Adjust in YPbPr, RGB, PC-RGB Input
Mode
▪ Red Gain : Controls Gain of Read Input
▪ Green Gain :Controls Gain of Green Input
▪ Blue Gain : Controls Gain of Blue Input.
▪ Red Bias , ▪ Green Bias, ▪ Blue Bias :
Controls Offset of each Bias
▪ Auto Color Balance : Selects RGB auto set
of Gain , Bias.
6-2. DISPLAY Setup
Sets Screen size mode or display status.
▪ Aspect : Sets picture ratio as 16 :9 or
as Native ratio in SD mode , 2K mode.
▪ 1:1 Scan :
ON-> Operates display at input Pixel
size in SD mode. (Not available in HD
Mode)
OFF ->Scales display to LCD size in
SD mode.
▪ Anamorphic : Makes vertical resize to
see Anamorphic screen(2.35:1) on
720/50P 59.94P mode.
▪ PaP Main : Selects input of left (main) screen from PaP (Picture and Picture) mode. Any Input signal
can be selected.(SDI1,2,CVBS1,2,3, S-VIDEO, YPbPr, RGB,PC-RGB,DVI)
▪ PaP Sub : Selects input of right( sub) screen from PaP (Picture and Picture) mode. Selectable sub
source is automatically changed depending on Main Source.
PaP Main PaP Sub
▪ Waveform Select : You can selectable Y,Cb,Cr
▪ Waveform/Vector Position :
Display Position : locates the Waveform & vector scope Position Display Position can
be located in any of the four corner.
▪ Vector Color 75%/100% :
Sets Input Color Reference Level in Vector Display.
Depending on 100% or 75%, Color, Marker position is changed.
▪ WFM & Vector Blend :
You can set the transparency of Waveform and Vector display.
▪ WFM & Vector Bright :
You can control the brightness of Waveform, Vector
▪ Pixel to Pixel (Option) : This function is available only in 7” and 20” model. Displays native signal inputted
in HD-SDI, 1920 x 1080 without scaling down. The active display can be set to Left Upper, Right Upper, Left
Bottom, Right Bottom, and Center.
Depending on the screen size & input signal resolution, pixel to pixel indicator moves as
follows.
6-2-1. DISPLAY (PC-RGB) Setup
This is displayed when PC-RGB(VGA) signal is selected.
▪ PC SCAN : Set output status as
Fill or Aspect Mode.
▪ V- Position : Adjusts vertical
position of screen for PC mode Input.
▪ H- Position : Adjusts horizontal
position of screen for PC mode Input
▪ Phase : Adjusts digital sampling
phase of SC of input signal (VGA
mode).
▪ Clock : Adjusts digital sample clock in PC-RGB mode
▪ AUTO Adjust : Adjusts the best display position automatically in PC-RGB mode(VGA)
▪ PaP Main, PaP Sub : Selects main input in PaP mode(left), Selects sub input in PaP. Please refer to
category 6-2 for detailed
6-3. COLOR Setup
▪ Color Temperature
Sets Color Temperature or White Balance on the
screen among VAR, 3200°K, 5400°K, 6500°K,
9300°K, USER
▪ VAR Number -> Selectable in steps from 1 to
63 from 3000°K ~ 9300°K
▪ USER -> Controls each RGB Gain and Bias.
▪ R,G,B Gain : Controls each R,G, B Gain in
User Mode.
▪ R,G,B Bias : Controls each R,G,B Bias in User Mode..
Please use professional (not included) to adjust Color Temperature (White Balance) to
precise adjustment.
* Color matrix Parameters use ITU Standard color. EBU color is set assuming parameters for an LCD
panel ; the best color is produced according to the standard for SDTV(ITU-R BT.601) , HDTV(ITU-R BT.709).
6-4. MARKER Setup
▪ Marker 16:9
Set the type of marker when the aspect ratio setting is 16 : 9 in HD signal.
- Type of Marker -> 4:3,15:9,14:9,13:9,1.85:1,2.35:1, USER, Off
▪ Safety Area 16:9
Selects the size of the safe area in 16 : 9 HD screen..
-> 95%,93%,90%, 88%,85%,80%,Off
EBU Action 16:9,EBU Graphic 16:9,
EBU Action 14:9,EBU Graphic 14:9,
EBU Action 4:3,EBU Graphic 4:3,Off
▪ Safety Area 4:3 : Selects the range of the Safe Area in 4: 3 SD mode.
-> 95%,93%,90%, 88%,85%,80%, EBU Action 16:9,EBU Graphic 16:9,EBU Action 14:9,
EBU Graphic 14:9,EBU Action 4:3,EBU Graphic 4:3,Off
▪ Center Marker : Center Marker ON/OFF
▪ Marker Color : Selects Marker Color -> White, Red, Green, Blue, Gray, Black
▪ Marker Back Color : Sets background transparency among Normal, Half, and
Grayscale excluding Safety area.
▪ Marker Thickness : Sets Marker Thickness as Pixel unit(1~10 pixel)
▪ User Marker H1 : Set the vertical line of Marker (left side: refer to below picture)
▪ User Marker H2 : Set the vertical line of Marker (right side)
▪ User Marker V1 : Set the horizontal line of Marker (upper)
▪ User Marker V2 :Set the horizontal line of Marker (lower)
User Marker Position can be controlled when User Mode is set in Marker 16 :9
6-5. OSD Setup
▪ Timecode Display
Displays Time Code on the
screen in
HD/SD-SDI signal input.
The position can be
located either top or
bottom.
Supports LTC in HANC,
VITC1 in HANC ,
VITC2 in HANC, DVITC
(SD-SDI).
▪ Timecode Position
Selectable timecode position between top or bottom.
▪ Status/Menu Display Time
Sets Menu and Information display time ->Select one of off, 0(continute)~60 secs.
▪ Status/Menu Blend
Set transparency of menus and indication windows on the screen
-> Selects 0~15 levels
▪ Menu Position
Selectable the location of MENU among Left Top, Right Top, Left Bottom, Right, Bottom, Center.
▪ V-Chip Display
If the SD-SDI or Composite have V-Chip data, can display it.
▪ Closed Caption
Display the Closed Caption data On/Off
※ Supports 608 Line 21 AUTO, 608 Line21 Manual, 608 VANC,608,
Transcoded, 708.
▪ Internal Pattern
Without additional Input signal, it provides internal Test Pattern of 1920 x1080 30p format on the screen.
(Off, Blue, Green, Red, 0~100% White)
▪ Source ID Display : User can enter Monitor ID on the screen.
▪ Source ID Character : User can enter Source (Monitor) ID which is displayed on the Monitor. Up to 10
digits writable.
▪ Source ID Position : Sets ID display position (Left-Top, Left-Bottom, Right-Top, Right-Bottom, Center)
6-6. AUDIO Setup
▪ Embedded Audio (L)
Select Digital Audio(L)
output from 1 to 16
channels when using SDI
input.
▪ Embedded Audio (R)
Select Digital Audio(R)
output from 1 to 16
channels when using SDI
input.
▪ Audio Level Meter :
Audio Level Meter display On/Off
▪ Level Meter Position :
Select position of displayed Audio Level Meter as Tom/Bottom on screen
▪ Speaker Source :
Select Speaker out source between Line (External input) and SDI (De-embedded).
▪ Speaker Output :
Select Speaker out pout among Left and Right channel.
▪ Speaker Volume : Control Speaker Volume.
6-7. GPI Setup
▪ GPI Control
Select external
control On/Off.
It is impossible to control
with Remote terminal
when it is Off.
▪ GPI Port 1, 2, 3, 4, 5, 6, 7
Assign each GPI port of external remote control terminal(RJ-45), It is impossible to double function
is prohibited.
Please refer to category 8-1.2.3 for detailed information.
▪ Remote ID Number
Sets Remote ID when you used remote control.
▪ Serial Remote
Sets Remote Control On/Off. When it is On the front button will be rocked.
To terminated Serial Remote status press the MENU button for 3sec.
GPI Port 7 is fixed at Standby.
To terminate Serial Remote status (Update or Remote ON), press the MENU button for 3 sec.
6-8. SYSTEM Setup
▪ Function 1, 2, 3, 4 :
Select the functions
to be assigned to each
function
buttons(F1,F2,F3,F4).
Please refer to category
3-4 for detailed
information.
▪ Back Light :
Adjust the backlight of
panel.
<0(min)~ 30(max) 0 (min)
~ 30 (max)>
▪ Front Button LED : LED light of Front button On/Off
▪ Front Button Lock : Front buttons lock On/Off
▪ Update Firmware : Updated Mode On/Off (Used for Firmware updated)
▪ Setup Load :This is used to make a group change of the function values which have been set.
- Factory : To return to the factory default.
- User 1, 2, 3 : Menu setting is transferred to the MENU of 1.2.3 that be saved by user.
▪ Setup Save : Save current menu setting into one of USER 1.2.3
User 1.2.3 can be recalled by Setup Load.
▪ Firmware Version : Currently System software version.
▪ Operating Time : Products operating time.
- To terminate the Update Firmware mode press the MENU button for 3 sec
- After change the backlight value, the panel requires enough time to be stable adjusting
Phase (brightness). It requires more than 30 minutes for aging.
7. Program Update Port
7-1. Program Update Port (RJ-11)
1) Firmware Upgrade.
Update Port used for 2) color calibration.
3) Remote control by PC.
7-2. Multiple Monitor Control
Multi Monitor Control can be operated by professional Adaptor(RS-232C <-> Serial Conversion) Converting
device and by PC where exclusive use program (Wall System Controller) is installed.
Please consult with technician for Program Update or for
Serial Port use. Incorrect use of this port may cause
8. Remote Terminal Assignment
8-1. Remote Terminal(RJ-45) Assignment
Each terminal function ca be set from the GPY CONTRO SETUP menu.
8-2. GPI Port(RJ-45)
Connect with external contact point.
Please refer to category 8-3 “Remote Terminal Assignment
8-3. Remote Terminal Assignment (GPI Port)
Port Assignment Items
Function
SDI Input
Switches the input SDI-1
CVBS1 Input
Switches the input CVBS1
CVBS2 Input
Switches the input CVBS2
CVBS3 Input
Switches the input CVBS3
Timecode Display
Waveform Display
Switches Waveform On/Off
1:1 SCAN
Switches 1:1 SCAN Function On/Off
KEY-ENTER
Switches Enter Button ON/OFF
KEY- MENU
Switches Menu On/Off
KEY-DOWN ▼
CURSOR DOWN during Menu Control.
KEY-UP ▲
CURSOR UP during Menu Control.
Safety Area 4:3
Controls Safety Area in 4 :93
Safety Area 16:9
Controls Safety Area in 16 :9.
H/V Delay On/Off
Switches H/V Delay Function On/Off
Center Marker On/Off
Switches Center Marker On/Off
SCAN
Selects Screen Size as shown in the front button
Aspect
Switches SD Aspect On/Off
MARKER On/Off
Switches Marker On/Off
MARKER Ratio
Selects Marker 16:9 Mode
Blue Only On/Off
Switches Blue Only On/Off
Grayscale On/Off
Switches Mono On/Off
Tally Amber On/Off
Switches Amber LED On/Off of Tally Lamp
Tally Green On/Off
Switches Green LED On/Off of Tally Lamp
Tally Red On/Off
Switches Red LED On/Off of Tally Lamp
Anamorphic On/Off
Switches Anamorphic On/Off
Pixel to Pixel On/Off
Switches Pixel to Pixel On/Off
Audio Display On/Off
Switches Audio Level On/Off
PaP On/Off
Switches PaP mode On/Off
S-Video Input
Switches the input Y/C
RGB Input
Switches the input RGB
YPbPr Input
Switches the input PbPr
VGA Input
Switches the input PC-RGB
DVI Input
Switches the input DVI
KEY-Standby
Port 7 Fixed. (Stand by Power On/Off)
9. List of Compatible Signal formats
Component
NO
Input Signal
Formats
Composite/
S-Video
YPbPr
RGB
SDI
DVI
1
NTSC √ - - -
-
2
PAL √ - - -
-
3
525/60i (SD)
- √ √ √ -
4
625/50i (SD)
- √ √ √ -
5
720*480/59.94p
- √ - - √
6
720*576/50p
- √ - - √
7
1280*720/23.98p
- - - - -
8
1280*720/24p
- - - - -
9
1280*720/50p
- √ - √ √
10
1280*720/59.94p
- √ - √ √
11
1280*720/60p
- √ - √ √
12
1920*1035/59.94i
- √ - √ √
13
1920*1035/60i
- √ - √ √
14
1920*1080/50i
- √ - √ √
15
1920*1080/59.94i
- √ - √ √
16
1920*1080/60i
- √ - √ √
17
1920*1080/23.98p
- √ - √ -
18
1920*1080/23.98psf
- √ - √ -
19
1920*1080/24p
- √ - √ -
20
1920*1080/24psf
- √ - √ -
21
1920*1080/25p
- √ - √ √
22
1920*1080/25psf
-
- - -
-
23
1920*1080/29.97p
- √ - √ √
24
1920*1080/29.97psf
-
- - -
-
25
1920*1080/30p
- √ - √ √
26
1920*1080/30psf
-
- - -
-
27
1920*1080/50p
- √ -
-
√
28
1920*1080/59.94p
- √ -
-
√
29
1920*1080/60p
- √ -
-
√
30
2048*1080/23.98p
- - - √ -
31
2048*1080/23.98psf
- - - √ -
32
2048*1080/24p
- - - √ -
33
2048*1080/24psf
- - - √ -
- With Analog YPbPr mode, 1035/59.94i,60i signal input, Marker is displayed in 1080/59.94i,60i and output.
- Output screen mode can be output with automatic control in DVI mode.
- STATUS Display of Input Signal might be different with real screen.
- Safety Area Edge part may not be displayed in some modes..
9-1. Computer Signals (PC-RGB/DVI)
NO
Input Signal
Names
Screen Resolution
PC-RGB
DVI
Vertical Frequency
1
VGA
640*480
√ √ 60Hz ~ 100Hz
2
SVGA
800*600
√ √ 56Hz ~ 85Hz
3
XGA
1024*768
√ √ 86Hz ~ 100Hz
4
WXGA
1280*768
√
√
50Hz ~ 85Hz
5
SXGA
1280*1024
√ √ 60Hz ~ 76Hz
6
WSXGA+
1680*1050
√ √ 50Hz~60Hz
7
UXGA
1600*1200
√ √ 60Hz Only
8
WUXGA*
1920*1080
-
√ ,note1
60Hz
9
WUXGA
1920*1200
-
√ ,note1
60Hz,( PC Only)
The output resolution can be change automatically as Graphic Card settings in PC-RGB(VGA), DVI input
mode.
10. Specifications
Section
BPM-071S
HD/SD-SDI Input
1EA, HD/SD Serial Digital, 1.485G/270M, BNC Jack
Analog Input
3EA, Composite, YC(S-Video), YPbPr, RGB, BNC Jack
PC-RGB(DVI) Input
1EA, DVI + Analog Jack (with gender) (24Pin + 5Pin)
Input
DVI Input
1EA, DVI-I, 24pin, Female
Output
SDI Output
1EA, BNC, Active Loop Output
Composite (CVBS)
1.0Vp-p(with sync), NTSC/PAL
YC(S-Video)
Y :1.0Vp-p, C:0.286Vp-p
Component (Y/Pb/Pr)
Y :1.0Vp-p, Pb :0.7Vp-p, Pr :0.7Vp-p
Component (R/G/B)
G :1.0Vp-p(with Sync), B :0.7Vp-p, R :0.7Vp-p
Analog
Input
Level
DVI-RGB,Sync Level
R, G, B : 0.7Vp-p, H/V Sync : 4V ± 1Vp-p
2K Format
2048*1080/24p, 23.98p, 24psf, 23.98psf
SMPTE 274M
1920*1080/60i, 59.94i, 50i, 24psf, 23.98psf
1920*1080/30p, 29.97p, 25p, 24p, 23.98p
SMPTE 296M
1280*720/60p, 59.94p, 50p
SMPTE 260M
1920*1035/60i, 59.94i
SMPTE 259M,125M
720*480/60i, 59.94i
ITU R-BT.656
720*576/50i
Component
640*480 up to 1920*1080p
DVI Digital
640*480 up to 1920*1200
Input Signal
Format
PC-RGB(DVI) Mode
640*480 up to 1280*1024, max 1600*1200
Input
1EA, L/R, Stereo pin jack
Audio Input
SDI Audio Input
Embedded HD/SD-SDI Audio
Output
1EA, L/R, Stereo pin jack
Speaker Output
1EA, 1W
Audio
Output
Output Signal
Input Line & De-embedded Audio, 1 ~ 16CH
GPI Remote
1EA, Remote, RJ-45P Jack, GPI-7 Port
I/O Port
Serial Update
1EA, Update, RJ-11P Jack, RS-422, Serial interface
Size
7.0”
Resolution
800 * 480
Pixel Pitch
0.1905 * 0.1905 mm
Color
16.7M
Viewing Angle (deg)
R/L:130, U/D:110
LCD
Luminance of White
350 cd/m² Power up brightness for daylight to 700 NIT
Contrast
400 : 1
Display Area (H * V)
152.4 * 91.44 mm
Power Requirements
DC 12V ~ 20V/5A
Power Consumption
0.1 ~ 1A(12W)
Operating Temperature
0°C ~40°C
Operating Humidity
20% ~ 80% RH
Weight
2.5 lbs.-1.3 kg
Dimension (W*H*D) w/o Box &
Stand
203 * 131 * 52 mm
Accessory Included
1-Power Cord 1-Manual
Option
Desk stand
11. DIMENSIONS
12. Trouble shooting
Solutions to common problems related to the monitor are described here.
If none of the solutions presented here solved the problem, unplug the monitor are consult an Authorized
Dealer or Service Center.
NO
Symptom
Probable cause and corrective action
Page
1
No power
• Firmly insert the Power Cord.
• Check the power. (100V ~220V)
2
No picture with
the power on
• Connect the signal cable firmly.
• Turn on the power of the connected
component and set the output correctly. Check
if the input signal format is acceptable to the
monitor.
3
No sound
• Connect the signal cable firmly.
• Adjust Volume Level.
4
Wrong color, no
color
• Check if the Hue is set up with basic
value
from the menu.
• Check if the color temperature is in
basic value.
5
Wrong picture
position, wrong
picture size
• Check if Pixel to Pixel mode is on.
• Adjust the picture size (H/V Position)
6
Menu does not
appear on the
screen or it is
shaking
• Items which are not available for the
current input or the current input signal
are not displayed on the menu. Change
input or the input signal.
Check if the input signal format is acceptable
for the monitor.
13. Maintenance
▪ When a still image is displayed for a long time, it may appear incorrectly due to heating on the screen. This
is due to the characteristics of the LCD display and is not a malfunction. Power cycle the monitor, and the
image will reset.
▪ Random fixed color dots (“stuck pixels”) on the panel surface are a normal characteristic of LCD displays,
and are not a problem. The LCD display is built with very high precision technology.
However, be aware that a few very small pixels may be affected by each other or lighting.
▪ Periodic maintenance inspection time of backlight is about 50,000 hours.
▪ Periodic maintenance inspection time of fan motor (option) is about 10,000 hours.
14. Update and Modification of Product
Specifications of this product may be changed without prior notice.
WARRANTY
For one year from the date of shipment, we will repair or replace your Glidecam
HD7 LCD, free of charge, in the event of a defect in materials or workmanship (the
shipment date appears on your purchase receipt) which occurs during normal use in
accordance with the Glidecam HD7 instruction manual. Shipping, packing, and
insurance costs to and from the factory are your responsibility. This limited warranty
extends only to the original purchaser, and you will need your purchase receipt.
This warranty does not cover, by way of example, damage caused by products not
supplied by us or damage resulting from mishandling in transit, accident, misuse,
vandalism, neglect, modification, lack of reasonable care of the Glidecam HD7 or
service by anyone other than us. There are no express warranties except as listed
herein. This warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
WE ARE NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE USE OF THE UNIT OR ARISING OUT OF ANY BREACH
OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING
THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED TO THE ONE YEAR WARRANTY PERIOD.
To obtain service during (or after) the warranty period: Contact Glidecam Industries’
Customer Service Department by calling 781-585-7900 or email at
tech@glidecam.com or write us at: 23 Joseph Street, Kingston, MA 02364, and
explain the problem.
DO NOT SEND THE UNIT TO US WITHOUT FIRST OBTAINING
A RETURN AUTHORIZATION NUMBER.
Glidecam Industries, Inc.
23 Joseph Street
Kingston, MA. 02364
TEL : 781-585-7900
FAX : 781-585-7903
Loading...