GLG LIGHTING EQUIPMENT
www.goedlichtengeluid.nl info@goedlichtengeluid.nl 1
Minispot 150
KEEP THIS MANUAL FOR FUTURE NEEDS
GLG LIGHTING EQUIPMENT
www.goedlichtengeluid.nl info@goedlichtengeluid.nl 2
1. GENERAL SAFETY INSTRUCTIONS
This device has left the GLG factory in perfect condition. In order to maintain this condition and to ensure a safe
operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in
this user manual.
If the device has been exposed to temperature changes due to environmental changes do not switch it on
immediately. The arising condensation could damage the device.
Leave the device switched off until it has reached room temperature.
This device falls under protection-class 1. Therefore it is essential that the device be earthed. The electric
connection must carry out by qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power
cord is never crimped or damaged by sharp edges. If this would be the case, replacement of the cable must be
done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power
cord by the plug. Never pull out the plug by tugging the power cord.
During initial start-up some smoke or smell mayarise. This is a normal process and does not necessarily mean
that the device is defective, it should decrease gradually.
Please don't project the beam onto combustible substances. Fixtures cannot be installed on combustible
substances, keep more than 50cm distance with wall for smooth airflow, so there should be no shelter for fans
and ventilation for heat radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the
manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
2. UNPACKING
Thank you for choosing our MINISPOT ML150. For your own safety, please read this manual before
installing the device. This manual covers the important information on installation and applications.
Please install and operate the fixture with following instructions. Meanwhile, please keep this manual
well for future needs.
The MINISPOT ML150 is made of a new type of high temperature strength of engineering plastics and cast
aluminum casing with nice outlook. The fixture is designed and manufactured strictly following CE standards,
complying with international standard DMX512 protocol. It's available independently controlled and linkable
with each other for operation. And it is applicable for large-scale live performances, theater, studio, nightclubs
and discos.
The MINISPOT ML150 adopts a 150W white LEDlamp which features high brightness and stability. Please
carefully unpack it when you receive the fixture and check whether it is damaged during the
transportation. And please check whether the following items are included inside the box:
①
④
①
MovingHead
1PC
②
SignalCable
1PC
③
PowerCable
1PC
④
OmegaClamp
1PC
⑤
SafetyCable
1PC
⑥
UserManual
1PC
GLG LIGHTING EQUIPMENT
www.goedlichtengeluid.nl info@goedlichtengeluid.nl 3
3. FEATURES
A 150W white LEDlamp, 7.500K, 50.000 hourslife span and low powerconsumption 8/16 bit smooth and
precise resolution for PAN/TILT movement 360° / 540° /630° PAN and 90° /180° /270° TILT movement
PAN/TILT inversion available.
Scan position memory, auto reposition after unexpected movement
Specific high precision glass optic system with 13.2° projection angle. Improved optics and flat beam field
1 rotatable gobo wheel with 6 rotatable and interchangeable gobos plus open with speed, adjustable, stream
effect, dithering effect and rotatable clockwise or anticlockwise.
Gobosize 23.9mm (external) / 15mm (inner)
Static gobo wheel with 11 gobos plus open
Frost filter
Colorwheel with 7 colors plus open
Variable direction rainbow effect with speed adjustable.
2 meter to infinite electric focus
6-facet prisma with variable speed and direction
0-100% smooth linear LED dimmer
Preset variable/random strobe and dimming pulse effect 25T/sec high speed LED shutter/strobe effect with
variable speed
14/12/16 DMX channels USITT DMX-512
DMX512, master-slave, and sound activated controllable or auto operation (7 built-in programs)
DMX recorder and edit function integrated
Blue LCD display
POWERCON connector IN/0UT, 3-pin XLR connector IN/0UT
Constant temperature readout and managementfunction
45° Cmax ambient temperature
IP20 protection rating
55dB at 3'dB rating
1·1/4 turn fastening Omega clamp
1* Safety attachment point
GLG LIGHTING EQUIPMENT
www.goedlichtengeluid.nl info@goedlichtengeluid.nl 4
4. CHANNELS
16B 8B DE
1 1 1
Pan
0-255
PAN movement
2
2 Pan-fine 0-255
Fine control of Pan movement
3
2
3 Tilt 0-255
Tilt movement
4
4 Tile-fine 0-255 Fine control of Tilt movement
5
3
5
Color
0-15
Open/white
16-31 Color1
32-47
Color2
48-63
Color3
64-79
Color4
wheel
80-95
Color5
96-111
Color6
112-127
Color7
128-189
Forwards rainbow effect from fast to slow
190-193
Color rotation stop
194-255
Backwards rainbow effect from slow to fast
6 4 6
Gobo
0-g
Open
10-19
gobo1
20-29
gobo2
30-39
gobo3
40-49
gobo4
50-59
gobo5
60-69
gobo6
wheel 1
70-89
Gobo1 shake slow to fast
90-109
Gobo2 shake slow to fast
110-129
Gobo3 shake slow to fast
130-149
Gobo4 shake slow to fast
150-169
Gobo5 shake slow to fast
170-189
Gobo6 shake slow to fast
190-255
Rot. gobo wheel cont. rotation slow to fast
7 5 7
Gobo1
0-3
No function
4-127
Forwards gobo rotation from fast to slow
rotation
128-131
Gobo rotation stop
132-255
Backwards gobo rotation from slow to fast
8 6 8
Gobo
0-g
Open
10-19
gobo1
20-29
gobo2
30-39
gobo3
wheel 2
40-49
gobo4
GLG LIGHTING EQUIPMENT
www.goedlichtengeluid.nl info@goedlichtengeluid.nl 5
50-59
gobo5
60-69
gobo6
70-79
gobo7
80-89
gobo8
90-99
gobo9
100-109
gobo10
110-119
gobo11
120-129
Gobo1 shake slow to fast
130-139
Gobo2 shake slow to fast
140-149
Gobo3 shake slow to fast
150-159
Gobo4 shake slow to fast
160-169
Gobo5 shake slow to fast
170-179
Gobo6 shake slow to fast
180-189
Gobo7 shake slow to fast
190-199
Gobo8 shake slow to fast
200-209
Gobo9 shake slow to fast
210-219
Gobo10 shake slow tofast
220-229
Gobo11 shake slow to fast
230-255
Rot. gobo wheel cont. rotation slow to fast
9
7 9
Shutter
0-31
Shutter closed
32-63
shutter open
64-95
Strobe effect slow to fast
96-127
shutter open
128-159
Pulse-effect in sequences slow to fast
160-191
shutter open
192-223
Random strobe effect slow to fast
224-255
shutter open
10
8 10
Dimmer
0-255
Dimmer 0%_1 00%
11 9
11
Focus
0-255
Ln (near) to out(far)
12 10
Rotating
0-5
OFF
6-127 0N
12
prism,
128-189
Forwards rotation from fast to slow
Prism rotation
190-193
Prism rotation stop
194-255
Forwards rotation from fast to slow
13 11 13
Speed
0-225
Max to min speed
226-235
Blackout by movement
pan/tilt
236-245
Blackout by all wheel changing
246-255
No function
14 12 14
Special 0-1g
No function
20-29
No function
30-39
Gobo Change to any position
40-79
No function
function
80-84
All Motor reset
GLG LIGHTING EQUIPMENT
www.goedlichtengeluid.nl info@goedlichtengeluid.nl 6
5. MENU OPTIONS
85-87
Scan motor reset
88-90
Colors motor reset
91-93
Gobo motor reset
94-96
Shutter & Dimmer motorreset
97-99
Other motor reset
100-119
lnternal program1
120-139
lntemal program2
140-159
lnternal program3
160-179
lntemal program4
180-199
lnternal program5
200-21 9
lntemal program6
220-239
lnternal program7
240-255
lnternal Sound program1
DMX
Address
A001-AXXX
DMX address setting
Auto Play
Auto Program
Master/Alone
Auto Program
Music Control
Master/Alone
Music Control
Reset ALL Reset
On/Off ALL Reset
Scan Reset
On/Off Scan Reset
Color Reset
On/Off Color Reset
GOBO Reset
On/Off GOBO Reset
Dimmer Reset
On/Off Strobe & Dimmer Reset
Other Reset
On/Off Other Reset
Reverse Pan
On/Off
Reverse Pan
Reverse Tilt
On/Off
Reverse Tilt
Mic sensitivity
0-99%
Sensitivity of mic
Special
Reset Default
On/Off Reset Default
Calibration
Code(Password:008)
Calibration Code
PAN. TILT, Color Wheel, Gobo
Calibration of the channel
Wheel 1, Gobo Wheel 2. Focus, Pri1
Temperature
XXX°C/°F
Current Temperature
Manual Control
PAN=XXX_ _
Manual Control
Signal Set
Wire DMX
Wire DMX
Wireless DMX
Wireless DMX
Act WDMX&
〇
ut Act WDMX& Out
Edit Program
Auto
Steps(1 _48)
Set Number of scenarios
Program1
Scenes 01
Pan=XXX_
Set the scenes channel
Program8
Scenes XX Time=xx.xS
Value & scenes times
GLG LIGHTING EQUIPMENT
www.goedlichtengeluid.nl info@goedlichtengeluid.nl 7
6. PHOTOMETRIC DATA
Photometric Beam Angle Data 3.2°Beam Angle= -xx 0.0929=Fc
2302/24790 573/6170 280/3020
177/1910
7. INSTALLATION
Cautions: For added protection mount the fixtures in areas outside walking paths, seating areas, or in areas
were the fixture might be reached by unauthorized personel.
Before mounting the fixture to any surface, make sure that the installation area can hold a minimum pointload
of 10 times the device's weight.
Fixture installation must always be secured with a secondary safety attachment, such as an appropriate safety
cable.
Never stand directly below the device when mounting, removing, or servicing the fixture.
from a ceiling, or set on a flatlevel surface (see illustration below). Be sure this fixture is kept at least 0.5m
(1.5 ft) away from any flammable materials (decoration etc.).
Always use and install the supplied safety cable as a safety measure to prevent accidental damage and/or injury
in the event the clamp fails.
Mounting points: overhead mounting requires extensive experience, including amongst others calculating
workingload limits, a fine knowledge of the installation, material being used, and periodic safety inspection of
all installation material and the fixture. If you lack these qualifications, do not attempt the installation yourself.
Improper installation can result in body injury!!
Be sure to complete all rigging and installation procedures before connecting the main power cord to the
appropriate wall outlet
Mode of
Standard Mode
Standard Mode
channel
Basic Mode
Basic Mode
Extended Mode
Extended Mode
Select Degree PAN Degree
630°/540°/360°
Pan Degree, default is 540°
TILT Degree
270°/180°/90°
Tilt Degree, default is
270°
Version
V1 0-V9.9
software Version
GLG LIGHTING EQUIPMENT
www.goedlichtengeluid.nl info@goedlichtengeluid.nl 8
Clamp Mounting: The MINISPOT ML150 provides two unique mounting bracket assembly’s that integrates the
bottom of the base, the included "0mega Bracket” and the safety cable rigging point in one unit (see the
illustration below). When mounting this fixture to truss be sure to secure an appropriately rated damp to the
included omega bracket using a M10 screw fitted through the center hole of the omega bracket). As an added
safety measure be sure to attached atleast one properly rated safety cable to the fixture using on of the safety
cable rigging point integrated in the base assembly.
Regardless of the rigging option you choose for your MINISPOT ML150, always be sure to secure your fixture
with a safety cable. The fixture provides a built-in rigging point for a safety cable on the hanging bracket as
illustrated above. Be sure to only use the designated rigging point for the safety cable and never secure a safety
cable to a carrying handle.
8. DMX 512 CONNECTIONS
Connect the provided XLR cable to the female3-pin XLR output of your controller and the other side to the
male3-pin XLR input of the moving head. You can chain multiple Moving head together through serial
linking. The cable needed should be two core, screened cable with XLR input and output connectors. Please
refer to the diagram below.
Pin 3
Pin 2
DMX-Pinning DMX-512 connection with DMX terminator (120 Ohms)
For installations where the DMX cable has to run along distance or is in an electrically noisy environment, such
as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption of the
digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 0hm resistor
connected between pins 2 and 3, which is then plugged into the output XLR socket of the last fixture in the
chain. Please see illustrations above.
9. Specifications
Input Voltage: AC 90-260V 50/60Hz
LED Quantities: 1 x 150W white LED
Control Signal: DMX512, master-slave and sound activated or auto operation 14/12/16
Control Channel: DMX channels USITT DMX-512
Power Consumption: 175W
Dimensions: 183(D) x 298(W) x 410(H)mm
Packing Dimensions: 270(D) x 370(W) x 590(H)mm
Net Weight: 9.5 kg
Gross Weight: 11 kg
Loading...