Glen Chimney hood User Manual

Features may vary with individual models. See product brochure for more details.

PDCA

Motor Housing

Thermal
Overload
Protector

(only in BF models)

Next Generation

BAFFLE

FILTER

Powerful

Suction

USERS GUIDE

CHIMNEY HOOD

INSTALLATION

The chimney must be mounted over the center of the cooking area. The
minimum distance between the cooktop and the bottom of the chimney must be
750 mm.

Join the two parts of the spigot (some models may have a single piece)
attach it to the hood using the four screws. In a few models the spigot may
already be mounted.

Fastening the chimney to the wall

Exhaust mode

Universal Spigot

The chimney must be connected by the spigot (supplied as part of the
hood) to a duct to vent all the exhausted air outside the kitchen. Over
horizontal areas, if any, the duct must be slanted about 10° downwards.

The diameter of the Duct pipe should be a minimum of 6” (15cm) for all

3

chimneys with suction of 1000m /h anything smaller than this will result in
vibrations at higher speeds.

The maximum recommended length of ducting is 10 feet with a maximum
of two bends. The suction power of the chimney considerably decreases in
case the length of the duct and number of bends increases further.

Re-circulation mode (Available in select model)

This mode is used when no exhaust duct to the outdoors is available. The
air is purified by an active carbon filter and recycled into the room.

The carbon filter is an optional attachment and must be procured in this
case.

Remove the metal filters. Insert the carbon filters and rotate it to lock at the
side of the hood. For effective functioning the carbon filters need to be
replaced after 3-4 months.

Mark the position of the holes on the wall. Before drilling make sure that no
wiring and tube will be damaged. Drill two fastening holes, drive in the wall
plugs and screw in the screw until their heads are about 6 mm from wall.

Place the chimney to the wall in order to check that it seats properly. Then
mark the position of the two holes. Take it off from the wall now, drill the holes
and fit the plugs. Place the hood once again to the wall, and introduce the
screw from the inside of the appliance.

The product can be used in re circulation or the exhaust mode. It is
however recommended that wherever possible it should be used in exhaust
mode for best results.

Your chimney now comes with a universal spigot for fixing the exhaust
pipe. It has 3 steps, one each suitable for 4’’, 5’ & 6’’ dia. pipe. Based on your
requirement you may cut the unwanted portion with hacksaw blade as
marked in the picture.

The cutting is required for 5’’ & 6’’ dia. Pipe for smooth flow of the air.

750 mm750 mm750 mm

UNIVERSAL SPIGOT

Opening dia. 5’’
Cut at this point

Opening dia. 6’’
Cut at this point

Opening Dia. 4’’Opening Dia. 4’’
No Cutting RequiredNo Cutting Required

Opening Dia. 4’’
No Cutting Required

Installing the duct covers

Fix the bracket with 2 plugs and screw at the required height for the duct cover. Screw the short duct with
2 screws on the bracket. Insert the 2 nuts in the holes on the lower part of the long duct. Put the long
pipe over the short one by pulling apart the laterals of the duct. Insert the nuts supplied, and working
from the inside of the chimney, using the two screws fix the long duct.

In few models the long duct can be fixed by using two screws which must be inserted into the holes at
the bottom of the duct.

Electric connection

Slider Control

Push Button Control

Soft Touch Electronic Control

Make sure that the supply voltage rating correspond with the specifications provided in the User’s Guide.

It has three speed setting and can be selected as per the
requirement by sliding the speed knob. For hob light, slide the
other knob.

It has four buttons and a light indicator. By pressing the first
button you can switch on the hob light. By pressing the second
button, chimney will start at speed 1 and indicator will start
glowing. Speed second and third can be selected by just
pressing the respective buttons.

To switch off just press the second button which has fan mark
on it. The chimney will be switched off.

It has four soft touch rectangle buttons and a digital display. By
just pressing the button with light indicator hob light will be
switched on. To start the chimney press the button having (+)
mark and to increase the speed press once more. The level of
speed will be displayed in the digital display. To reduce the
speed or to switch off press the button which (-) mark .

It also has an auto off timer and to set this you have to press the button with the clock on it and the
display will show the time it can be set between 1-99 minutes by pressing again and again. Once you
leave the same, the Chimney will switch off automatically at the end of the timer.

Switch on the chimney 5 minutes before you start cooking.

The Soft Touch Electronic push button/slider control have three speed settings. Kindly choose the speed
as per your requirement.

USAGE

II III

POWER

INDICATOR

SPEED 2 SPEED 3FAN ‘ON’

SPEED 1

BULB

TIMER

(1-99 min.)

LIGHTDIGITAL DISPLAY

(Speed / Time)

SPEED SELECTION

+

-