GLEELITE GL350BSWT, GL350BSW User Manual
GL350BSWT Moving Head Lighting
User manual
Thanks for choosing our goods please read this manual carefully before your operating
2
Contents
Introduction........................................................3
Dimensions.........................................................4
Safety Information..............................................5
Using for the first time........................................7
AC power............................................................8
Data link..............................................................8
Setup....................................................................9
Menu chart..........................................................10
DMX Protocol&Channel Function.....................14
Service and maintenance.....................................19
Cleaning..............................................................20
3
Introduction
350W Beam Spot Wash 3 in 1 Moving head light with CMY
Model:GL350BSWT
Moving Head Lighting
Voltage:AC100V-240V
50/60Hz Power
Consumption:500W Light
source:YODN R17 350W
Color Temperature:8000K
Beam Angle:1.5°- 35° linear fast zooming.
Focus:High precision optical lens,electronic linear control
Linear Dimmer:Mechanical dimmer 0-100%
CMY Color Wheel:Cyan+Magenta+Yellow color wheel with total 15 colors
Rotating Gobo Wheel:12 rotating gobos+White/,bi-directional rotatable and gobo
shaking at variable speeds
Static Gobo Wheel: 13 interchangeable gobos + effect gobo+ white, and
bi-directionally rotatable and gobo shaking at variable speeds
Prism:12+36facet circular prism rotating in both directions at variable speeds
Dimmer:0-100% linear dimmer
Strobe:1-18/second,double lens strobe with adjustable speed
Pan and Tilt: Smoothly,automatic Pan/Tilt position correction,speed adjustable
Range:Pan540°，Tilt 280°
Effect:Color+Gobo+Prism+Strobe automatic operation function
Cooling:Fan Cooling
Control mode:Standard DMX 512, 3 pin,5 pin connector
Channel mode:21/23/28 Channels
Display Interface:LCD screen both in Chinese and English
IP rate:IP20,Built-in overheat protection,triggered high voltage protection.
Net Weight:19KG
Gross Weight:23.5KG(Carton)
4
Dimensions
5
Safety Information
The following symbols are used to identify important safety information on the product and in this manual:
WARNING!
Read the safety precautions in this section before
installing, powering, operating or servicing this
product.
！
DANGER!
Hazardous
voltage. Risk
of lethal or
severe electric
shock.
WARNING!
Burn hazard.
Hot surface.
Do not touch.
WARNING!
Refer to user
manual.
WARNING!
High brightness
light source,
With risk of
burned eyes.
Protection
from burn
and fire.
DANGER!
Safety hazard.
Risk of severe
injury or death.
WARNING!
Wear
protective
Eye wear.
Warning!
High brightness light source,don’t look at the light directly so that keep the risk of burned eyes
away.
This product is for professional use only. It is not for household use.
This product presents risks of severe injury or death due to fire and burn hazards, electric shock
and falls.
Read this manual before installing, powering or servicing the fixture, follow the safety precautions
listed below and observe all warnings in this manual and printed on the fixture.
If have any problem,please contact the supplier.
6
PROTECTION FROM ELECTRIC SHOCK
• Disconnect the fixture from AC power before removing or installing any cover or part and when not in
use.
• Always ground (earth) the fixture electrically.
• Use only a source of AC power that complies with local building and electrical codes and has both
overload and ground-fault (earth-fault) protection.
• Before using the fixture, check that all power distribution equipment and cables are in perfect condition
and rated for the current requirements of all connected devices.
• Power input and throughput cables must be rated 20 A minimum, have three conductors 1.5 mm²
(16 AWG) minimum conductor size and an outer cable diameter of 5 - 15 mm (0.2 - 0.6 in.). Cables must
be hard usage type (SJT or equivalent) and heat-resistant to 90° C (194° F) minimum. In the EU the cable
must be HAR approved or equivalent.
• Use only Neutrik Powercon NAC3FCA cable connectors to connect to power input sockets. Use only
Neutrik Powercon NAC3FCB cable connectors to connect to power throughput sockets.
• Isolate the fixture from power immediately if the power plug or any seal, cover, cable, or other
Component is damaged, defective, deformed, wet or showing signs of overheating. Do not reapply
power until repairs have been completed.
• Do not expose the fixture to rain or moisture.
PROTECTION FROM BURNS AND FIRE
• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).
• The exterior of the fixture becomes hot during use. Avoid contact by persons and materials. Allow
the fixture to cool for at least 10 minutes before handling.
• Keep all combustible materials (e.g. fabric, wood, paper) at least 100 mm (3.9 in.) away from the
fixture.
• Keep flammable materials well away from the fixture.
• Ensure that there is free and unobstructed airflow around the fixture.
• Do not expose the front glass to sunlight or other strong light sources from any angle.
• Do not illuminate surfaces within 200 mm (7.9 ins.) of the GL350BSWT
• Do not attempt to bypass thermostatic switches or fuses.
• Do not stick filters, masks or other materials onto any optical component.
• Do not modify the fixture in any way not described in this manual
Loading...