GLD Products Laser Dart Line Mounting Instructions

Laser Dart Line Mounting Instructions #37-0108

Backboard
Dartboard

Laser Dart Line
Level

Cabinet
Dartboard

Laser Dart Line
Level

Cabinet
Door

Laser Dart Line

Side View

Mounting Holes

Close Up

Make sure your mark
is centered in the oval

OFF ON

AVOID EXPOSURE LASER RADIATION IS EMITTED FROM THE APERTURE
AVOID DIRECT EYE EXPOSURE

DANGER

Max Output <5mW, Wavelength 650nm-660mm, Class II Laser Product

Complies with FDA Radiation Performance Standards 21 CFR Chapter 1, Subchapter J
GLD Products, Muskego, WI 53150, Model #37-0108
ACCESSION NO:1410047-000

When the laser beam dims, or stops operating, replace batteries
Dispose of batteries promptly and properly, Do not burn them
Use only fresh batteries of the required size and type
Do not mix old and new batteries, or different types
If you do not plan to use the Laser Dart Line for a month or more remove batteries,
batteries can leak chemicals that can damage electronic parts

WARNING! Never look directly into the laser
WARNING! Keep away from children
WARNING! Never point the device towards anyone’s eyes
WARNING! Laser light can also be dangerous when refl ected on a mirror-like surface
WARNING! Use of controls or adjustments, or the performance of procedures other than specifi ed herein,
can result in hazardous radiation exposure

Read all instructions carefully before mounting the Laser Dart Line.

The Laser Dart Line can be mounted directly to a wall or the underside of a dartboard cabinet.

Required tools: pencil, screws, screwdriver, tape measure, drill, drill bit, and level.

Instructions

1) Mount your dartboard or dart cabinet. With one hand, place the Laser Dart Line on the wall or cabinet directly below

and centered to the dartboard. With your other hand, level the Laser Dart Line.

2) Locate the two mounting holes on the front of the Laser Dart Line. Use a pencil, marker, or nail to mark the center of
the holes on the wall or cabinet.

3) Drill a pilot hole on each mark that you created in step two. If using plastic anchors for dry wall, plaster, or cement, drill
the holes so that the anchors fi t snugly. Insert the plastic anchor. If drilling into a wood cabinet or wood stud, only pilot
holes will be necessary.

4) Align the Laser Dart Line with the anchors or pilot holes and screw the Laser Dart Line into place. The screws will
expand the plastic anchors. Before tightening the screws, check that the Laser Dart Line is level.

5) Remove the front battery cover and insert 4 AA batteries. The Laser Dart Line can also be powered by an AC to 5v
1000 mA adapter with DC plug polarity confi gured as positive (+) outside and negative (-) inside. (4 AA Batteries and
adapter not included). Adapter item #42-9987 is available from GLD Products.

CAUTION:

Publication 37-0108 Rev C
August 2017

The power adapter is not a battery charging device.
Do not plug in the power adapter when the Laser Dart Line is turned on.

Remove all the batteries before plugging in the power supply.

GLD Customer Service:

Email: [e-mail]

www.gldproducts.com

6) Measure the distance for your throw line

The laser line should be 96 " from the face of the dartboard

Soft Tip

Dartboard

Wall

The laser line should be 93 ¹/ " from the face of the dartboard

Steel Tip

Dartboard

Wall

Temporary line

Measure
96" or 93¼"

Measure
96" or 93¼"

Adjust the angle of the laser head
so that the line appears the correct
distance from the wall

Temporary line

Laser Dart Line

by G L D P R O DU C TS

®

Use a common household item,
such as a broom handle or ruler,
to make a temporary line at the
correct distance. Measure from
each side of the dartboard to the
temporary line.

7) Once your laser throw line is set, tighten the 2 screws next to ball to secure the Laser Line in place.

8) WARNING: AVOID DIRECT EYE EXPOSURE
Turn the Laser Dart Line on and position the laser head until it is fl ush with your temporary line.

9) If your surface area is uneven, loosen either the left or right screw and place shims behind the housing of the Laser
Dart Line until the Laser Dart Line is in the correct position.

Please call or consult the GLD website, gldproducts.com, to order the 5V 1000ma Positive Outer
Power Adapter, #42-9987.

WARRANTY: Great Lakes Dart Mfg, Inc. warrants this product to be free of defects in material and workmanship for a
period of 90 days by the original purchaser of the unit. This warranty covers manufacturers defects only, not normal wear
and tear. This warranty does not apply to products damaged through accidents, misuse, or neglect. Your warranty is void
if service is attempted by anyone other than the manufacturer or authorized agent. Great Lakes Dart Mfg., Inc. reserves
the right to make an inspection and determination of all warranty claims. For questions concerning products of Great
Lakes Dart Mfg., Inc., please call our Customer Service Representatives at 1-800-225-7593.

Muskego, WI 53150
www.gldproducts.com