Page 1
A family company manufacturing in the USA
www.glastender.com
Project:
Item #: Qty:
Model #:
GWS66
The GWS66 includes:
• GW24 glasswasher with 01001500 Slideout Chemical Bottle Rack
• SWB-18-DW wet waste sink cabinet with
03005491 trash receptacle
• DBGR-24-RS drainboard glassrack with
roll-out shelves
AIA#
SIS#
SWB-18-DW
Glastender, Inc. • 5400 North Michigan Road • Saginaw, MI • 48604-9780
989.752.4275 • 800.748.0423 • Fax 989.752.4444
www.glastender.com
Specications subject to change without notice. For current specications please visit our website.
Printed in USA
1.13
DBGR-24-RS
GW24
Approval/Notes:
Rev. 08-05-15
Page 2
SWB-18-DW as part of the GWS66 glasswashing station
DRY WASTE CHUTE
DRAIN
18"
24"
30"
18"
30"
37"
6"
24"
FRONT ELEVATION SIDE ELEVATIONPLAN VIEW
For more detailed specications, see Spec
Sheet Wet Waste Sink Cabinets 3.21
SWB-18-DW
03005491
Trash Receptacle
Standard Features
• Manufactured with total welded construction to meet NSF®
standards
• All stainless steel construction
• Adjustable stainless steel bullet feet
• 9-1/4" by 11-1/2" by 6" deep sink bowl with hot and cold
water gooseneck faucet
• Faucets are standard and ship mounted
• Lift-out perforated plastic wet waste strainer
• Cabinet base with work surface trash chute hole and front
hinged access door with lock. Accessory part #03005491
28-1/2 quart trash receptacle is included with the GWS66
glasswashing station.
Specications
Drain
• 1-1/2" I.P.S. Threaded drain will fit Dearborn part #8033
slipnut and part #W-573P washer.
Faucet
• Deck mount on 4" centers, accepts 3/8" sink leads, hot and
cold water connections required
Sink Bowl Dimensions
• 9-1/4" by 11-1/2" by 6" deep
Sink Strainer
• Perforated plastic
Legs
• 1-5/8" diameter, 16 gauge stainless steel
• Stainless steel bullet feet
Materials
• 20 gauge stainless steel parts include: all components unless
otherwise noted
• 18 gauge stainless steel parts include: leg pads
Dimensional Information
5400 North Michigan Road • Saginaw, MI • 48604-9780
989.752.4275 • 800.748.0423 • Fax 989.752.4444
www.glastender.com
Printed in USA
Page 3
24"
15.531"
GW24 Rotary Glasswasher as part of the GWS66 glasswashing station
5-15P
Specications
General Plumbing [Hot water and cold water required]
• Plumb with 1/2" water supply. Adapt to 3/8" FMPT.
• Minimum water pressure is 25 PSI
• Maximum water pressure is 100 PSI. Install water pressure regulator if line pressure is over 100 PSI. Water valve on unit has
built-in strainer and flow control to provide consistent volume
between 25 and 100 PSI
• Install separate water shutoff valve
• Unit has built-in air gap
- vacuum breaker is not
required
• Consumption is 3 gallons
per cycle
Hot Water Supply
• Maximum temperature is
150ºF (66ºC)
• Minimum temperature is
130ºF (54ºC)
Cold Water Supply
• No minimum temperature requirement
GW24
with 01001500
For more detailed specications,
see Spec GW24 1.12
Slide-out
chemical rack
Drain
• 1-1/2" tailpiece.
• Use open type floor drain for maximum drainage
Electrical
• 120V, single phase, 60Hz, 6-foot NEMA 5-15P
grounded cord included
• Dedicated 15 amp circuit recommended
• Power requirements - 3.5 amps
Detergent
• Extra heavy duty, non-foaming, commercial liquid dishwashing
detergent is required - .30% concentration
• Consult local chemical supplier to match detergent with local
water conditions
Sanitizer
• Liquid chlorine bleach (sodium hypochlorite - 5.25% solution)
adjusted to 50 ppm
Rinse Aid
• Liquid Rinse Aid adjusted for proper sheeting
Operation / Capacity
• 120°F (49ºC) minimum wash temp and rinse temp adjustable
down to 75°F (24ºC)
• 2 minute 15 second cycle
• 2-3/4" diameter bar glasses - 41 per cycle
• 2-1/2" diameter bar glasses - 49 per cycle
• Maximum glass height 10"
G
W
Dimensional Information
Sliding
Door
10-3/32"
Open
14.75"
24"
PLAN VIEW
7"
Mechanicals
Note: 1. In all cases, consult local plumbing, electrical and health codes for
regulations which may not be consistent with the information on the
front of this specification sheet
2. The utility connections are made from the floor at the bottom of the
unit approximately 7" to 8" high.
3. The Glastender policy of constant quality improvement means
specifications are subject to change without notice.
30" 30.75"
6"
FRONT VIEW SIDE VIEW
24"
7"
24"
10.625"
5"
4.312"
2
3
1
1 = DRAIN
2 = HOT WATER
5400 North Michigan Road • Saginaw, MI • 48604-9780
989.752.4275 • 800.748.0423 • Fax 989.752.4444
www.glastender.com
3 = COLD WATER
4 = ELECTRICAL
10.5"
7.5"
4
9"
Printed in USA
Page 4
DBGR-24-RS as part of the GWS66 glasswashing station
24"
PLAN VIEW SIDE ELEVATIONFRONT ELEVATION
Standard Features
For more detailed specications, see
Spec Drainboard Glassracks 3.15
DBGR-24-RS
(Glassrack not included)
• All stainless steel construction
• Adjustable stainless steel bullet feet
• One piece, seamless top and backsplash featuring 1/4" radius
corners for easy cleaning
• Roll-out bottom shelf and one roll-out intermediate shelf
(intermediate shelf is not adjustable)
• Solid shelves are also useable for non-glassrack storage
• Exclusive design drainboard top with drain pan and separate
perforated insert for better air circulation
• Intermediate shelf and floor are still removable after unit is
plumbed and include radius corners for easy cleaning
• Smooth interior walls for easy cleaning & finished appearance
Specications
Drain
• 1/2" welded tailpiece. Clear vinyl drain line is connected to the
tailpiece at the factory. A 1/2" by 1/2" barbed plastic elbow is
provided to make the connection at the bottom of the unit.
Legs
• 1-5/8" diameter, 16 gauge stainless steel
• Stainless steel bullet feet
Materials
• 20 gauge stainless steel parts include: all components unless
otherwise noted
• 18 gauge stainless steel parts include: leg pads
Dimensional Information
ROLL-OUT
SHELF
5400 North Michigan Road • Saginaw, MI • 48604-9780
989.752.4275 • 800.748.0423 • Fax 989.752.4444
www.glastender.com
24"
15 1/4"
37"
24"
7"
ROLL-OUT
SHELVES
24"
30"
6"
Printed in USA
Loading...