GT-18+3L
(view from cocktail server side)
Project:
Item #: Qty:
AIA#
SIS#
Model #:
GT-18+3L or GT-18+3R
Glasswasher
Rotary Rack, Fill & Dump, Circular Pass Thru Glasswasher
Standard Features
• Designed for pass thru cocktail stations. Allows bartenders and
cocktail servers to start, load and unload glasswasher
• Removable top for easy cleaning access
• Drive Wheel and Glass Rack lift out for cleaning
• Three 16" diameter polypropylene racks included
• Set of two curtains included
• Removable side panels for easy service access
• Spray box unlatches for easy cleaning and visual inspection - 15
spray nozzles have been engineered for maximum soil removal
• Digital temperature gauge built into switch panel
• Intelligent microprocessor control delays cycle start, up to two min
utes, when incoming water is below 120ºF (49ºC)
• Built-in cabinet for chemical storage
• Automatic peristaltic metering pumps accurately dispense detergent,
sanitizer and rinse aid
• Prime Switch for quick chemical priming
• 1/6 HP pump recirculates wash water and rinse water
• Fractional HP drive motor powers the belt-driven rotary rack and
includes built-in slip clutch
-
Specications
General Plumbing
• Plumb with 1/2" water supply. Adapt to 3/8" FMPT.
• Minimum water pressure is 25 PSI
• Maximum water pressure is 100 PSI. Install water pressure reg ulator if line pressure is over 100 PSI. Water valve on unit has
built-in strainer and flow control to provide consistent volume
between 25 and 100 PSI
• Install separate water shut-off valve
• Unit has built-in air gap - vacuum breaker is not required
• Maximum temperature is 150ºF (66ºC)
• Minimum temperature is 120ºF (49ºC).
• Consumption is 2-1/2 gallons per cycle
Drain
• 1-1/2" tailpiece.
• Use open type floor drain for maximum drainage
Electrical
• 120V, single phase, 60Hz, 6-foot grounded cord included
• Dedicated 15 amp circuit recommended
• Power requirements - 3.5 amps
Detergent
• Extra heavy duty, non-foaming, commercial liquid dishwashing
detergent is required - .30% concentration
• Consult local chemical supplier to match detergent with local
water conditions
Sanitizer
• Liquid chlorine bleach (sodium hypochlorite - 5.25% solution)
adjusted to 50 ppm
Glastender, Inc. • 5400 North Michigan Road • Saginaw, MI • 48604-9780
989.752.4275 • 800.748.0423 • Fax 989.752.4444
www.glastender.com
Specications subject to change without notice. For current specications please visit our website.
Printed in USA
1.09
Rinse Aid
• Liquid Rinse Aid adjusted for proper sheeting
Capacity
• 2 minute cycle, 70 second wash and 22 second rinse exposure
• 10 glasses† per minute or 600 per hour (maximum glass height
10" - including pitchers and wine carafes)
Materials
• 20 gauge stainless steel parts include: cabinet
• 18 gauge stainless steel parts include: floor and tanks
• 16 gauge stainless steel parts include: leg mounting brackets and legs
• 11 gauge stainless steel parts include: drive wheel
Installation Considerations
• 1" clearance required to remove top
• Bartender side service is essential
• Detergent, Sanitizer, and Rinse Aid containers are stored in the
cabinet. Storage available for two five-gallon and one one-gal-
lon containers. (Chlorine Sanitizer should be stored in one-gal-
lon container.)
† Based on 2-3/4" diameter bar glasses
Approval/Notes:
Rev. 11-02-07
GT-18+3L and GT-18+3R Glasswashers
WORK SURFACE
GLASS RACK
(3 PROVIDED)
PASS
THRU
1 = HOT WATER
2 = DRAIN
3 = ELECTRICAL
1
2
3
1
3
2
THRU
PASS
Elevations (GT-18+3L Model Shown)
Plan Views
R
E
D
N
E
T
S
A
L
G
R
E
D
N
E
T
S
A
L
G
R
E
D
N
E
T
S
A
L
G
R
E
D
N
E
T
S
A
L
G
R
E
D
N
E
T
S
A
L
G
R
E
D
N
E
T
S
A
L
G
R
E
D
N
E
T
S
A
L
G
R
E
D
N
E
T
S
A
L
G
R
E
D
N
E
T
S
A
L
G
R
E
D
N
E
T
S
A
L
G
R
E
D
N
E
T
S
A
L
G
R
E
D
N
E
T
S
A
L
G
1" ADJUSTMENT FROM 38-1/2" TO 39-1/2"
CHEMICAL STORAGE (TWO 5-GALLON CONTAINERS
BARTENDER SIDE
SERVER SIDE
GT-18+3L GT-18+3R
AND ONE 1-GALLON CONTAINER)
PLAN VIEWSBARTENDER SIDE BARTENDER SIDE
WITHOUT FRONT PANEL
36"
31 1/2"
26"
28"
38 1/2"
4 1/2"
13"
38 7/16"
36"
19 3/8"
20 1/8"
30 1/4"
38 1/2"
36"
31 1/2"
26"
3"
13"
7"
3"
7"
13"
38 7/16"
20 1/8"
36"
36"
19 1/2"
19 3/8"
Note: 1. In all cases, consult local plumbing, electrical
and health codes for regulations which may
not be consistent with the information on the
front of this specification sheet
2. The utility connections are made from the floor
at the bottom of the unit approximately 7" to
8" high.
3. The Glastend er policy of constant quality
improvement means specifications are
subject to change without notice.
Dimensional Information
Mechanicals
5400 North Michigan Road • Saginaw, MI • 48604-9780
989.752.4275 • 800.748.0423 • Fax 989.752.4444
www.glastender.com
Printed in USA
Loading...