Glastender GT-18+1 General Manual

GT-18+1

Project:

Item #: Qty:

AIA#

SIS#

Model #:

GT-18+1

Glasswasher

18" wide by 41-1/16" deep Rotary Rack, Fill & Dump,

Front-to-Back Pass Thru Glasswasher

Standard Features

• Built-in drain table at rear for manual loading by cocktail server

• Removable top for easy cleaning access (GT-18, GT-18+1, GT-18+1L, GT-18+1R, GT-18+2, and GT-18+1-IC tops are interchangeable)

• Drive Wheel and Glass Rack lift out for cleaning

• Two 16" diameter polypropylene racks included

• Set of two curtains on cocktail server side included

• Removable side panels for easy service access

• Spray box unlatches for easy cleaning and visual inspection - 15 spray nozzles have been engineered for maximum soil removal

• Digital temperature gauge built into switch panel

• Intelligent microprocessor control delays cycle start, up to two min utes, when incoming water is below 120ºF (49ºC).

• Automatic peristaltic metering pumps accurately dispense detergent, sanitizer and rinse aid

• Prime Switch for quick chemical priming

• 1/6 HP pump recirculates wash water and rinse water

• Fractional HP drive motor powers the belt-driven rotary rack and includes built-in slip clutch

Specications

General Plumbing

• Plumb with 1/2" water supply. Adapt to 3/8" FMPT.

• Minimum water pressure is 25 PSI

• Maximum water pressure is 100 PSI. Install water pressure reg ulator if line pressure is over 100 PSI. Water valve on unit has built-in strainer and flow control to provide consistent volume between 25 and 100 PSI

• Install separate water shut-off valve

• Unit has built-in air gap - vacuum breaker is not required

• Maximum temperature is 150ºF (66ºC)

• Minimum temperature is 120ºF (49ºC).

• Consumption is 2-1/2 gallons per cycle

Drain

• 1-1/2" tailpiece.

• Use open type floor drain for maximum drainage

Electrical

• 120V, single phase, 60Hz, 6-foot grounded cord included

• Dedicated 15 amp circuit recommended

• Power requirements - 3.5 amps

Detergent

• Extra heavy duty, non-foaming, commercial liquid dishwashing detergent is required - .30% concentration

• Consult local chemical supplier to match detergent with local water conditions

Glastender, Inc. • 5400 North Michigan Road • Saginaw, MI • 48604-9780

989.752.4275 • 800.748.0423 • Fax 989.752.4444 www.glastender.com

Specications subject to change without notice. For current specications please visit our website.

Printed in USA

1.04

Sanitizer

• Liquid chlorine bleach (sodium hypochlorite - 5.25% solution) adjusted to 50 ppm

Rinse Aid

• Liquid Rinse Aid adjusted for proper sheeting

Capacity

• 2 minute cycle, 70 second wash and 22 second rinse exposure

• 10 glasses† per minute or 600 per hour (maximum glass height 10" - including pitchers and wine carafes)

Materials

• 20 gauge stainless steel parts include: cabinet

• 18 gauge stainless steel parts include: floor and tanks

• 16 gauge stainless steel parts include: leg mounting brackets and legs

• 11 gauge stainless steel parts include: drive wheel

Installation Considerations

• 1" clearance required to remove top

• Front side service is essential

• Detergent, Sanitizer, and Rinse Aid containers are stored exter- nally - six-foot lengths of tubing are provided. Storage for three one-gallon containers is required within five feet

† Based on 2-3/4" diameter bar glasses

Approval/Notes:

Rev. 11-02-07

GT-18+1 Glasswasher

FRONT

THRU

PASS

BAR DIE CUT-OUT FOR GT-18+1

BACK VIEW

BAR DIE CUT-OUT FOR GT-18+1 WITH

3 = ELECTRICAL

2 = DRAIN

1 = HOT WATER

OPTIONAL GLASS RACK HOLDER

BACK VIEW

DOOR OPEN

FRONT

(2 PROVIDED)

GLASS RACK

PLAN VIEW

1" ADJUSTMENT FROM 38-1/2" TO 39-1/2"

ELEVATION VIEW

41-1/16"

5-1/4"

48-9/16"

7-1/2"

12-3/4"

18-1/8"

24-3/4"

A.F.F.

38-1/2"

7-1/2"

1" Minimum Clearance

10-3/4" A.F.F.

24-3/4"

18-1/8"

18"

41-1/16"

12-3/4"

20"

7-1/2"

Note: 1. In all cases, consult local plumbing, electrical

and health codes for regulations which may not be consistent with the information on the front of this specification sheet

2. The utility connections are made from the floor at the bottom of the unit approximately 7" to 8" high.

3. The Glastend er policy of constant quality improvement means specifications are subject to change without notice.

18"

Dimensional Information

Mechanicals

5400 North Michigan Road • Saginaw, MI • 48604-9780

989.752.4275 • 800.748.0423 • Fax 989.752.4444 www.glastender.com

Printed in USA