Customer Pole Display
SERIES 8035
Operation Manuanl
Version 1.1
`
This equipment has been tested and found to comply with the
limits for Class A digital device. Pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in are side ntial installation. This
equipment generates, uses, and if not installed and used in
accordance with the instructions may cause harmful interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on.The user is
encouraged to try correct interference by one or more of the
Following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This booklet is available from the U.S. government Printing Office,
Washington, DC 20402, Stock
NO.004-000-00345-4.
CAUTION:
Any changes of modifications not
expressly approved by the grantee of this device
could void the user’s authority to operate the
equipment.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received including
interference that may cause undesired operation.
`
Table of Contents:
Chapter 1
Introduction ........................................................4
Chapter 2
Appearance ........................................................5
Chapter 3
Before You Install................................................6
Chapter 4
Installing Model 8035
USB Interface..................................................7,8
Chapter 5
Programming Commands..............................9,10
Appendix I
Specifications....................................................11
Appendix II
Character Generator ROM Map........................12
`
Chapter 1
The 8035 LCD customer display is an excellent tool for
transmitting transactions, advertising message, and
customer greeting at POS system(point-of-sale system).
With adjustable tilt angles and visual swivel, customer
could freely set just right angel and pole height
according to their demand. The bright alphanumeric LCD
display provides wide viewing angles,no matter in close or
short distance. 8035 LCD customer display support
language (Europe/English). With ESC/POS command
codescompatible,8035 can work under any operation
system and platform.
Features:
Easy to read of blue background & white characters
Introduction
display.
Six adjustable viewing angles and visual swivel design
Language support: (Europe/English)
USB communication
Built-in ESC/POS command codes, compatible to
OPOS of ESC/POS
4
`
Chapter 2
Cable Connector
Appearance
LCD Display
`
JD-8035
5
Chapter 3
Before You Install
This manual describes functions and usage of the Model 8035
customer pole display. The 8035 is a 2x20 alphanumeric customer
pole display designed with multi-languages for retail and other
industrial environments. Its outstanding features include high
quality liquid crystal display in blue & white color,USB & serial
interface are easy to use and powerful programming features.
The 8035 can also combine with any serial receipt printer.
Step 1: Turn Off Your Computer
By shutting off your computer, you will prevent any accidental damage to the
pole display and computer.
Step 2: Review Packing List
Please ensure that your pole display shipment is complete.
Model 8035 USB includes:
• 1 pcs 8035 pole display
• 1 pcs operation manual
• 1 pcs USB cable
• 1 pcs pole
NOTE: The last character of indicates Cable’s color.
Ex: W=White; B=Black
6
`
USB Interface
Step 1: Installation USB Driver
Select the driver for your system
software and installed
After installation complete select “OK”
7
`
Step 2: Bulid up your 8035
USB A USB B
Step 3: Connect to your computer
Connect the USB connector to the port on your computer.
Then check device installed normally in device manager.
Notes: COM number may be different on each computer
8
`
Chapter 5
Programming Commands
There is a programming mode available for model 8035 with ESC/POS mode.
In this Chapter,
we will use ESC/POS mode for multi-languages, Please refer to Appendix for
details.
The basic function of the 8035 display is comparable to the display
programming by your software should be as easy. You only need open the
COM-port on which the display has been connected from you. Then, you just
needs send the character what you want to display on 8035 directly via the
COM port. Please following the USB/RS232 parameters to use as below:
9600 Baud, No Parity, 8 Data Bits, 1 Stop bit
In Basic, you would initialize the interface as follows:
OPEN “COMx: 9600, N, 8, DS0” FOR OUTPUT AS #1
(x=number of the COM port you are using for the display)
And you would print something to the display using the PRINT command:
PRINT#1, “Hello World!”
In the end, you can close the interface:
CLOSE #1
In other programming languages, the commands for serial output shall be
different, but they will work in a similar way. For some compilers, you will
need
an extra toolbox, that offers you usb routines. Please refer to your
compiliers/interpreters manual for more details.
Example:
OPEN “COMx: 9600, N, 8, 1, DS0” FOR OUTPUT AS #1
PRINT #1, “Hello World!”
CLOSE #1
9
`
Programming using DOS routines
You can also generate a display output using the simple DOS routines.
Example:
MODE COMx: 9600, N, 8, 1
ECHO Hello! >COMx:
Control characters and special functions
For special display functions, there are some commands which will be
explained in this chapter. Some of the commands consist of one
ASCII-CTRL-code, others are command strings, introduced by ESC.
If a command needs additional parameters, please do not forget to use ASCII
format for the parameter. That means, if the parameter is 0 (zero), then you
have to transmit the ASCII code “0” (=CHR$(48) in Basic; 48 is the decimal
position of the “0” character in the ASCII code table). But please consider that
only ONE byte is allowed for each parameter. That is why you cannot transmit
two digit numbers. In this case, just add the number you want to transmit as
parameter 48 and transmit the corresponding character. For example, if you
want to transmit the parameter 11, you have to send
CHR$(11+48)=CHR$(59)=“;”. Attention: For some other commands, only
BYTE values are allowed as parameter. For those, you directly send the
corresponding character code without adding 48 (e.g. CHR$(11) for 11). For
details, please refer to the individual command code descriptions.
Example: Set the cursor to the last position in the display area
WRONG:
PRINT #1, CHR$(27)+“=”; :REM command ESC =
PRINT #1, 19;1 :REM parameter column 19, line 1
CORRECT:
PRINT #1, CHR$(27)+“=”;
PRINT #1, CHR$(48+19)+“1” :REM or CHR$(48+19)+CHR$(48+1)
Below is a list of command sequences for user to design an interface to the
8035 customer pole display.
Please note that pole display is default with 9600 bps baud rate, no parity,
8 data bits, 1 stop bit.
10
`
Appendix I
Specifications
NO
1 Display method Liquid crystal display
2 LCD type STN Blue mode
3 Backlight mode LED backlight
4 Brightness 600 cd/m2
5 Display color Blue(back color) and White(character color)
6 Adjustable angle Swivels 360° and Tilt 45° Angles
7 Viewing angle 0– 45 degrees
8 Number of character 20 columns x 2 lines
9 Character size 5mm(w) x 10mm (H) , 5x7 dot
10 Character font 2 x 20 dot matrix by alpha numeric
11 Language Europe/ English
12 Interface USB 2.0 user access 8035 via virtual Comport
13 Software Programming ESC/POS OPOS (OLE for Retail POS)
14 Power Requirement 5V DC from HOST USB port
15 Total dimensions 214 (W) x 70 (H) x 40 (D) mm
Item Descriptions
16 Optional Pole Height 140mm or 280mm
17 Approximate Weight 950g
18 Material ABS Plastic & ABS Plastic with Metal
19 Colors Dark Gray or White
20 Operating temperature 5 - 45℃
21 Operating Humidity 30% - 85%
22 Storage Temperature -10 - 55℃
23 Storage Humidity 10% - 85%
11
`
Appendix II
Character Generator ROM Map
12
`
Loading...