Gladiator GAWG302DPG00 Owner’s Manual
WAll GEARBOXCABINETS
AssembFyInstructions
ARMARIOSMODULARES
Instruccionesde ensamblaje
ARMOIRESA OUTILSMURALES
lns#uctionsd'assemblage
TableofContents/indice/Tabledesmati6res.............2
24" (60.96 cm) Cabinet
Armario de 24" (60,96 cm)
Armoire de 24 po (60,96 cm)
30" (76 crn)Cabinet
Annado de 30" (76 cm)
Armoire de 30 po (76 cm)
TABLEOFCONTENTS TABLEDESMATIERES
CABINET/LOCKER SAFETY ......................................................... 2
ASSEMBLY INSTRUCTIONS ......................................................... 3
Tools and Parts ............................................................................ 3
Cabin_ Use Requirements.......................................................... 3
Unpack the Cabinet ..................................................................... 3
Mount the Cabinet to the Wall ..................................................... 3
Installthe Shelves ........................................................................ 4
DoorAdjustment .......................................................................... 4
Door Reversal............................................................................... 4
WARRANTY ................................................................................... 5
INDICE
SEGURIDAD DEL ARMARIO ........................................................ 6
INSTRUCClONES DE ENSAMBLAJE .......................................... 6
Piezasy herramientas.................................................................. 6
Requisitosde uso del armario..................................................... 6
Desempaque del armado............................................................. 6
Monte el armario enla pared....................................................... 6
tnstalelos estantes....................................................................... 7
Ajustede la puerta ....................................................................... 8
C6mo invertireleierre de la puerta.............................................. 8
GARANTL_....................................................................................... 8
SECURITE DE L'ARMOIRE ........................................................... 9
INSTRUCTIONS D'ASSEMBLAGE ................................................ 9
Outillage et pi_cesn_eessalres................................................... 9
Specificationsd'utilisationde I'armoire....................................... 9
D6ballagede I'armoire................................................................. 9
Montage de I'armoiresur lernur .................................................. 9
Installationdes dtag_res ............................................................ 11
Reglage des portes .................................................................... 11
Inversiondu sensd'ouverture des portes ................................. t t
GARANTIE ..................................................................................... 12
CABINET/LOCKERSAFETY
Your safety and the safety of others are very important.
We have provided many importantsafety messages in this manual and on your appliance. Always read and obey all
safety messages.
This symbol alertsyou to potential hazards that can killorhurtyou and others.
Allsafety messages willfollow the safety alert symbol and eitherthe word "DANGER" or
This isthe safety alert symbol.
"WARNING." These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tellyou how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
ASSEMBLYINSTRUCTIONS
Too sand Par
Check that you have everything necessary for correct assembly.
Proper assembly is your responsibility.
Tools Needed:
• 1/2in. Wrench (GearWallTM • Phillips screwdriver
panel mount) • _,_in. Wrench
• 7A_in. Wrench (Standard • "/32in. Wrench
mount)
Parts Supplied for 24 in. (60.96 cm) Cabinet:
• % - 20 x 1_ in. Lag • 1/4in. Flat washers (4)
screws (4)
Parts Supplied for 30 in. (76 cm) Cabinet:
• Keys (2) • 1/4- 20 x 1V2in. Lag
• Full-width shelves (2) screws (4)
• 1/4in. Flat washers (4)
Cabinet Use Requirements
• Not intended for flammable material storage.
• Intended for use in a garage.
• Maximum weight limit is 50 Ibs (22 kg) for each shelf.
• Maximum weight limit is 200 Ibs (91 kg) for the 30 in. (76 cm)
cabinet.
• Maximum weight limit is 150 Ibs (68 kg) for the 24 in.
(60,96 cm) cabinet.
2. Determine cabinet mounting location on GearWallTM panels.
3. Using 2 or more people, engage the mounting bracket into
the wall slots by lifting up, pushingtoward the wall and
lowering the mounting bracket rims into the slots (see
Graphic 1).
4. Make sure the mounting bracket is fully engaged inthe slots
(see graphic 2).
Install 30 in. (76 cm) Cabinet - 2 mounting brackets
NOTE: Loosen the 3 nuts on the bottom mounting bracket just
enough so the mounting bracket will move in the slots.
1. Close the cabinet doors.
2.
Determine cabinet mounting location on GearWallTM panels.
3.
Using 2 or more people, engage the top mounting bracket
into the wall slots by lifting up, pushing toward the wall and
Iowedng the mounting bracket rims into the slots
(see graphic 1).
4. Make sure the top mounting bracket is fully engaged in the
slots (see graphic 2).
5. Open the cabinet doors.
6. From the inside, lift up on the bottom mounting bracket by
the 2 outer bolts until the mounting bracket aligns with the
slots on the GearWall TM panel.
7. Push the cabinet toward the GearWallTM panel and lower the
bottom mounting bracket rims into the slots.
8. Make sure the bottom mounting bracket is fully engaged in
the slots.
J
J
Unpack the Cabinet
I. Open the cabinet door.
NOTE: On the 30 in. (76 cm) cabinet you must first remove
the keys and unlock the door.
2. Remove end verify the contents (see "Parts Supplied").
3. Properly dispose of packaging.
M unt the Cabinet fo the Wall
Install Cabinet to GearWall _ Panels
IMPORTANT: Check to ensure that the GearWa[I TM panels are
installed with mounting screws in every slot and at every stud
location with a maximum of 24 in. (60,96 cm) horizontally
between screws.
Install 24 in. (60.96 cm) cabinet - 1 mounting bracket
1. Close the cabinet door.
1 2
1. Mounting brackets
2. Mounting brackets fully engaged,
9. Using a 1/2in. wrench, tighten the 3 nuts on the bottom wall
mounting bracket.
10. Inspect the cabinet from the sides to ensure both the top and
bottom wall-mounting brackets are fully engaged in their
respective slots as shown.
/
D
Install Cabinet to Standard Wall
IMPORTANT:
• Remove the GearWall TM mounting bracket(s) before installing
the wall cabinet on your standard wall.
• Use the round holes in the rear cabinet wall to mount the wall
cabinet to your garage wall studs.
1. Locata the wood studs in your garage wall and mark the
holes.
2. Using 2 or more people, align 4 corresponding holes inthe
cabinet with the marks on the wall.
3. While 2 or more people hold the cabinet in place on the wall,
attach the wall cabinet to the garage wall using the 1/_in. flat
washers and lag screws.
4. Using a 7/_sin. wrench, fully tighten the bolts.
tnstGflthe Shelves Door Adjuslrnenf
3. Insertthe shelf into the cabinet so that the higher end and the
rear edge are directly above the desired metal tabs end push
down to snap shelf edges in place behind the rear and side
tabs.
NOTE: As the lower shelf edge slides upward it will press in the
tab, allowing it to pass.
4. Raise the lower end so it is directly above the desired tab and
push down to snap shelf edge in place behind the side tab.
5. Make sure the shelf edges are in place behind all the tabs and
the shelf is firmly supported.
6. Repeat this process for the other shelf.
To Remove the Shelves
1. Liftup on the underside of the shelf untilthe shelfedges are
free of the cabinet tabs.
2. Tilt the shelf up to reposition it within the cabinet or to remove
it from the cabinet.
24 in. (60.96 em) Cabinet The cabinets ore designed with adjustable door(s).
The 24 in. (60.96 cm) cabinet has 1 fixed shelf. No installation or
adjustment is required.
30 in. (76 cm) Cabinet
NOTE: Plan your shelf heights and install shelves startingfrom
the bottom. The shelves are supported by the metal tabs on the
back and side walls of the cabinet.
1. Determine the placement of the shelves.
2. Tilt the shelf so that one end is higher than the other as
shown.
1. Using a Philips screwdriver, loosen all screws attaching the
hinge to the cabinet.
2. Adjust door to the desired height.
3. Tighten the screws.
Door I ever !
(24 in.(60.96cm) ,._lt cabinets only)
1. Using a Phillips screwdriver, remove all the screws securing
the cabinet door hinge to the cabinet. Set the cabinet door
aside.
2. Remove the nut securing the cabinet door latch to the wall
cabinet. Reattach the cabinet door latch to the hole on the
opposite side of the wall cabinet.
3. Using the screws removed in step 1, reattech the cabinet
door hinge to the opposite side of the cabinet.
2 IIII1
I. Push down
2. Uft up
Loading...