STEEL WALL GEARBOX
FULL-DOOR CABINET
Assembly Instructions
ARMARIO DE ACERO PARA HERRAMIENTAS, PARA PARED
- PUERTA COMPLETA
Instrucciones de ensamblaje
ARMOIRE À OUTILS MURALE EN ACIER - PORTE PLEINE
Instructions d'assemblage
TABLE OF CONTENTS/ÍNDICE/TABLE DES MATIÈRES
PARTS ...........................................................2
CABINET/LOCKER SAFETY .......................3
ASSEMBLY INSTRUCTIONS.......................3
Cabinet Use Requirements........................3
Unpack Cabinet Parts................................3
Assemble Cabinet Frame ..........................3
Attach Back Panels....................................4
Install Doors ...............................................4
Install Shelves ............................................5
INSTALLATION INSTRUCTIONS................5
Install Cabinet to GearWall
or GearTrack
Standard Wall Mount .................................6
WARRANTY ..................................................6
®
Channels ............................5
®
Panels
PIEZAS .......................................................... 2
SEGURIDAD DEL ARMARIO ..................... 7
INSTRUCCIONES DE ENSAMBLAJE ........7
Requisitos de uso del armario...................7
Desempaque las piezas del armario.........7
Ensamblaje del marco del armario............ 7
Fije los paneles posteriores .......................8
Instalación de las puertas..........................9
Instalación de los estantes ........................ 9
INSTRUCCIONES DE INSTALACIÓN.........9
Instale el armario a los paneles GearWall
o a los canales GearTrack®........................9
Montaje de pared estándar .....................10
GARANTÍA ..................................................11
®
PIÈCES..........................................................2
SÉCURITÉ DE L’ARMOIRE....................... 12
INSTRUCTIONS D’ASSEMBLAGE........... 12
Spécifications d’utilisation de l’armoire .. 12
Déballage des composants de l'armoire 12
Assemblage du châssis de l'armoire ...... 12
Fixation des panneaux arrière ................. 13
Installation des portes .............................13
Installation des étagères.......................... 14
INSTRUCTIONS D'INSTALLATION..........14
Installation de l’armoire sur des panneaux
GearWall
Montage mural standard ......................... 15
GARANTIE .................................................. 15
®
ou des profilés GearTrack®..... 14
ES TIEMPO DE VOLVER A PENSAR EN EL GARAGE.™
W10233395C
IT'S TIME TO RETHINK THE GARAGE.
LE GARAGE REPENSÉ.™
®
P1
PARTS/PIEZAS/PIÈCES
P9
F1
P4
P2
F2
P1
P6
F3c
P6m
P8
P5
F7
P3
P7
F8
2
CABINET/LOCKER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
follow instructions.
can be killed or seriously injured if you don't
You
instructions.
follow
ASSEMBLY INSTRUCTIONS
Cabinet Use Requirements
■ Intended for use in a garage.
■ Maximum weight limit is 40 lbs (18 kg) for each shelf.
■ Maximum weight limit is 150 lbs (68 kg) for the cabinet.
Unpack Cabinet Parts
1. Remove and verify the contents. Contents include an hex key
and the parts and fasteners shown in “Parts.”
2. Dispose of/recycle all packaging materials.
Assemble Cabinet Frame
F1
F1
⁵⁄₁₆
" Hex-head bolt (16)
Gather the required tools before starting installation.
Tools Needed:
■ ¹⁄₂" Wrench ■ Phillips screwdriver
Tools Supplied:
■ Hex key
IMPORTANT:
■ Two people may be required to complete the assembly.
■ The cabinet top (P2) is intentionally designed so that the tabs will
only match with the loops on the sides when it is positioned
correctly. If the tabs on the cabinet top do not match up with the
loops on the side panel (P1), turn the cabinet top around.
1. Place side panel (P1) on a flat, firm surface so that the edge with
the loops is facing up.
2. Align the tabs in the cabinet top (P2) with the loops in the cabinet
side (P1). Slide the cabinet top between the edges of side panel.
NOTE: Make sure each tab is inserted fully behind the loop.
P2
P2
A B
P1
A. Tab
B. Loop
3. Align the two holes in each corner. Using hex-head bolts (F1),
fasten the side panel (P1) to the top (P2) as shown. Do not
tighten completely.
4. Repeat steps 2 and 3 for the other cabinet side (P1).
5. With the smooth side toward the cabinet interior, align the four
tabs in the cabinet bottom (P3) with the loops in the cabinet
sides (P1). Slide the cabinet bottom between the edges of side
panels.
NOTE: Make sure each tab is fully inserted behind the loop.
3
6. Align the two holes in each corner. Using hex-head bolts (F1),
fasten the side panels (P1) to the bottom (P3) as shown. Do not
tighten completely.
P2
P4
P1
P1
P3
P1
P3
Attach Back Panels
F3c
Phillips-head screw (5)
1. Align the seven tabs in the upper back panel (P4) with the loops
in the top (P2) and sides (P1) of the cabinet.
2. Slide the upper back panel (P4) toward the cabinet top (P2) until
the back panel is firmly in place.
NOTE: Make sure each tab is inserted fully behind the loop as
shown.
A
P1
P5
P3
6. Completely tighten all back panel screws.
7. Starting with the front of the cabinet, using the hex key
(provided), completely tighten all the bolts.
Install Doors
F3c
Phillips-head screw (8)
The door hinges are designed with keyhole slots at the top and
bottom so the door will hang on the cabinet while you are fastening
the screws.
1. Start Phillips-head screws (F3c) in both the top and bottom holes
on each side of the cabinet.
2. Hang the right-hand side door (P7) from the top and bottom
screws, and hand tighten.
3. Insert the middle two screws through the door hinge into the
cabinet and hand tighten.
P4
P1
P1
P3
A. Holes to install mounting bracket
3. Align the four side tabs on lower back panel (P5) with the loops in
the cabinet sides.
4. Slide the lower back panel upward until the top of the lower
panel is under the upper back panel (P4).
NOTE: The upper back panel will slightly overlap the lower back
panel.
5. Using Phillips-head screws (F3c), fasten the upper back panel
(P4) to the lower back panel (P5) and the lower back panel to the
cabinet bottom (P3).
4
P2
P4
P5
P7
P1
P3
4. Repeat steps 2 and 3 to attach the left-hand door (P8).
5. Align the doors and completely tighten the screws.
Install Shelves
A
Plan your shelf heights and install the shelves starting from the
bottom. The shelves are supported by the metal loops on the side
walls of the cabinet.
1. Determine the placement of the shelves (P6 and P6m).
2. Place the shelf (P6) in the cabinet so that the long edge with the
holes is toward the front of the cabinet.
3. Tilt the shelf so that one end is higher than the other as shown.
4. Repeat steps 2 and 3 for the other shelf (P6m) with magnet.
NOTE: The higher end of the shelf should be directly above the
cabinet loop at the desired height.
B
A. Push down.
B. Lift up.
5. Push the shelf edge down so the shelf tabs go into the cabinet
loops.
6. Lift up on the lower end of the shelf so it is above the desired
cabinet loop and push the shelf down into place.
NOTE: Make sure the shelf tabs are in place behind all the
cabinet loops as shown.
7. Repeat steps 2 through 5 to install the other shelf.
A
■ If installing cabinet on GearTrack
should be installed 18" below the bottom of the supporting
channel so the cabinet will hang level.
18" (46 cm)
®
channel, a second channel
Attach Mounting Bracket
F7 F8 F2
F7 Carriage-head bolt (2)
F8 Washer (2)
1. With the mounting bracket (P9) rims pointing down, align the two
bracket holes with the two holes in the top back
panel (P4).
2. Working from the back, insert a carriage bolt (F7) through the
bracket and top back panel (P4).
3. Working from the cabinet interior, fasten each bolt with a
washer (F8) and a flange nut (F2). Fully tighten the bolts.
4. Close the cabinet doors.
F2
⁵⁄₁₆
" Flange nut (2)
P2
P2
P4
P9
P4
P1
P1
P9
A. Cabinet loop
B. Shelf tab
INSTALLATION INSTRUCTIONS
WARNING
Excessive Weight Hazard
Use two or more people to move, assemble or install
cabinet.
Failure to do so can result in back or other injury.
B
IMPORTANT: Decide if you are going to mount the cabinet on
Gladiator
standard wall.
IMPORTANT:
■ Be sure the GearWall
®
GearWall® panels or GearTrack® channels, or on a
Install Cabinet to GearWall® Panels
or GearTrack
®
installed with mounting screws in every slot and at every stud
location with a maximum of 24" (60.96 cm) horizontally between
screws.
panels or GearTrack® channels are
®
Channels
P5
A. Bracket rim pointing down
A
Mount on GearWall® Panels or GearTrack® Channels
1. Determine cabinet mounting location on GearWall® panels or
GearTrack
2. Using two or more people, engage the mounting bracket into the
wall slot by lifting up, pushing toward the wall and lowering the
bracket rim into the slot.
3. Inspect the cabinet from the sides to ensure the wall-mounting
bracket is fully engaged in the slot as shown.
A
®
channels.
A. Bracket rim
B. Slot
B
C
C. Mounting bracket
fully engaged
5
Loading...