Gladiator GAWB08HWGW Installation Instructions
Models:
GAWB04HWEG
GAWB06HWEG
GAWB06HWGW
GAWB08HWEG
GAWB08HWGW
ADJUSTABLE HEIGHT
WORKBENCH
Assembly Instructions
ÉTABLI À HAUTEUR
AJUSTABLE
Instructions d’assemblage
MESA DE TRABAJO
CON ALTURA
REGULABLE
Instrucciones de ensamblaje
TABLE OF CONTENTS/TABLE DES MATIÈRES/ÍNDICE
WORKBENCH SAFETY ......................2
DIMENSIONS ......................................3
PARTS .................................................. 4
ASSEMBLY INSTRUCTIONS .............. 5
Tools and Parts .................................5
Workbench Use Requirements ......... 5
Unpack the Workbench ....................5
Install Legs and Back Panel..............5
Inner Leg Height Adjustment ............ 7
Complete the Assembly ....................8
Workbench Care ............................... 8
Registering Your Product ..................8
WARRANTY ......................................... 9
SÉCURITÉ DE L’ÉTABLI ...................10
DIMENSIONS ....................................11
PIÈCES ..............................................12
INSTRUCTIONS D’ASSEMBLAGE ... 13
Outils et pièces ............................... 13
Spécications d’utilisation
de l’établi ........................................13
Déballage de l’établi .......................13
Installation des pieds et du
panneau arrière ............................... 13
Ajustement de hauteur des pattes
internes ........................................... 15
Fin de l’assemblage ........................ 16
Entretien de l’établi .........................16
Enregistrement de votre produit .....16
GARANTIE ......................................... 17
SEGURIDAD DE LA MESA
DE TRABAJO ....................................19
DIMENSIONES .................................. 20
PARTES ..............................................21
INSTRUCCIONES DE
ENSAMBLAJE ................................... 22
Herramientas y piezas ....................22
Requisitos para el uso de la mesa
de trabajo ........................................ 22
Desempaque la mesa de trabajo .... 22
Instale las patas y el panel trasero .22
Regulación de la altura de las
patas internas ................................. 24
Complete el ensamblaje .................25
Cuidado de la Mesa de trabajo ......25
Cómo registrar el producto .............25
GARANTÍA ......................................... 26
W11100254E
In U.S.A. call: 1-866-342-4089
Aux É.-U. : 1 866 342-4089
En EE.UU. Ilame al: 1-866-342-4089
In Canada call: 1-800-807-6777
Au Canada : 1 800 807-6777
En Canadá Ilame al: 1-800-807-6777
www.gladiatorgarageworks.com
www.gladiatorgarageworks.ca
WORKBENCH SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
follow instructions.
You
can be killed or seriously injured if you don't
instructions.
follow
2
DIMENSIONS
A
C
B
Model GAWB04HWEG GAWB06HWEG
GAWB06HWGW
A
B
C
48"(122 cm) 72"(183 cm) 96"(244 cm)
25"(63.5 cm) 25"(63.5 cm) 25"(63.5 cm)
27.5" - 40.8"(69.9 cm - 103.6 cm) 27.5" - 40.8"(69.9 cm - 103.6 cm) 27.5" - 40.8"(69.9 cm - 103.6 cm)
GAWB08HWEG
GAWB08HWGW
3
F14
4
F16
F18
P1
F19
PARTS
F1
P3
P4
F16
P1
F19
F20
F19
P2
F18
F19
F17
F20
F18
F19
F20
P2
P6
P1. Workbench outer legs
P2. Workbench inner legs
P3. Back panel
P4. Workbench top
P6. 1/2" (12.7 mm) x 2" (50.8 mm)
leveling legs
F14. M8 hex-head bolts
F16. 3/8" (9.5 mm) x
1½" (3.81 cm) screws
F19
P2
F16
P6
F17. Wing nuts
F18. 5/16" (8 mm) hex-head bolts
F19. ID 8 mm x OD 12.5 mm x
F20. Bushing
F19
F18
F19
F17
F20
P2
THK 3 mm washer
F14 F18 F19
4
ASSEMBLY INSTRUCTIONS
Tools and Parts
Gather the required tools and parts before starting installation.
Tools Needed
■ 9/16" socket wrench ■ Adjustable wrench
Parts Supplied
4 ft (121.9 cm), 6 ft (182.9 cm), and 8 ft (243.9 cm) Workbench
■ Workbench outer legs
(2 welded sets)
■ Workbench inner legs (4)
■ Workbench back panel
■ Workbench top
■ 1/2" (12.7 mm) Leveling legs
(4)
■ M8 hex-head bolts (5)
■ 3/8" (9.5 mm) x 1½" (3.81 cm)
screws (15)
■ Wingnuts (8)
■ 5/16" (8 mm) hex-head
bolts (8)
■ ID 8 mm x OD 12.5 mm
x THK 3 mm washer (8)
■ Bushing (8)
■ 5 mm wrench (1)
Workbench Use Requirements
WARNING
Excessive Weight Hazard
Use two or more people to move and assemble
workbench.
Failure to do so can result in back or other injury.
■ Intended for use in a garage.
■ Maximum weight limit is 3,000 lbs (1,360 kg).
■ Adding casters to this workbench could be a tipping hazard.
Unpack the Workbench
1. Unpack the legs and hardware from the box. Verify contents.
See the “Parts Supplied” section.
NOTE: Workbench Legs come fully assembled.
2. Remove the back panel and set it aside.
NOTE: Leave the workbench top on the cardboard during
assembly.
3. Remove the corners from the workbench top. The bolt holes
should be visible. Inspect workbench top prior to assembly.
4. Dispose of/recycle all packaging materials.
Install Legs and Back Panel
NOTE: Assemble and adjust this workbench upside down according to the following illustrations. Be sure that the workbench top is at
on the oor and the legs are in the air. To protect the workbench top during assembly, it is recommended that you place the wood top
upside down on the cardboard provided in the package.
1. Prepare workbench top
Lay the workbench top (P4) upside down on a clean surface to
expose the holes for the leg assembly sets.
2. Place leg assemblies
Place each outer leg assembly (P1) on the workbench
underside. Line up the holes in the outer leg assembly sets
with the holes on the bottom of the workbench top (P4). Each
outer leg assembly end has two holes that must face the three
holes on the back of the wood top for installation of the back
panel.
5
3. Attach leg assemblies
4. Attach back panel to leg assemblies
Attach the leg assemblies (P1) to the workbench top (P4)
using eight of the provided 3/8" (9.5 mm) x 11/2" (3.81 cm)
screws (F16). Make sure the screws are inserted straight into
the holes. Loosely install the screws using a 9/16" socket
wrench. Do not tighten the screws completely.
NOTES:
■ Tightening the screws at an angle can place excessive
stress on the screws, which may cause the screws to fail.
■ The holes in the legs are oval to allow space for minor
adjustments as the workbench is assembled.
5. Attach back panel to workbench top
Using a 5 mm wrench, attach the back panel (P3) to the leg
assemblies (P1) with the four provided M8 hex-head bolts
(F14). Do not tighten the bolts completely.
6. Tighten leg assembly bolts
Attach the back panel (P3) to the workbench top (P4) using
the remaining screws*. Make sure that the screws are inserted
straight into the holes. Tighten the screws using a 9/16"
socket wrench.
NOTE: Tightening the screws (F16) at an angle can place
excessive stress on the screws, which may cause the screws
to fail.
*NOTE:
For 4' workbench, use two screws (F16).
For 6' workbench, use three screws (F16).
For 8' workbench, use six screws (F16).
6
Using a 5 mm wrench, tighten the bolts to attach the back
panel (P3) to the outer leg assemblies (P1) completely.
NOTE: Do not overtighten the bolts and screws.
7. Tighten bolts and screws
8. Attach the leveling legs
Tighten all remaining bolts and screws.
NOTE: Do not overtighten the bolts and screws.
If not already installed, screw in the four leveling legs (P6).
The leveling legs have a at side designed for use with an
adjustable wrench, if needed.
IMPORTANT: To install the leveling legs, turn clockwise a
minimum of 1½" (3.8 cm), or 12 full turns. Further adjustment
can be made 1/4" (6 mm) down from this position or until the
leveling leg cannot be turned any further against the bottom of
the inner leg (P2).
Inner Leg Height Adjustment
NOTE: Adjust this workbench upside down according to the illustrations. Be sure that the workbench top is at on the oor and the legs
are in the air.
2. Attach leg assemblies1. Align adjustment holes
Before setting the workbench upright, verify that the same
number of adjustment holes are visible with no more than 11
exposed holes on each leg to ensure that the workbench will
be level. Align the adjustment holes in the inner leg (P2) with
the adjustment holes in the outer leg assembly (P1) at the
desired height of the workbench.
Insert a 5/16" (8 mm) hex-head bolt (F18) and washer (F19)
and secure with a wingnut (F17). Be sure the hex-head bolt
aligns with the hex-shaped adjustment hole. Repeat for each
leg.
NOTE: To minimize multiple adjustments during assembly,
make sure the adjustment holes are aligned at the same
desired height for all the legs.
7
Complete the Assembly
WARNING
Excessive Weight Hazard
Use two or more people to move and assemble
workbench.
Failure to do so can result in back or other injury.
2. Adjust leveling legs1. Stand up workbench
Using two or more people, stand the workbench upright and
place it in its nal location.
Adjust the leveling legs as needed.
IMPORTANT: When adjusting the leveling legs, be sure they
are installed at least 11/2" (3.8 cm) or 12 full turns deep into the
legs.
Workbench Care
1. Wash the workbench with a mild detergent and warm water. Do not allow water to remain on the workbench for any length of time.
2. Rinse completely and dry thoroughly.
Registering Your Product
There are many benets of registering your product. Find out more and register your product online at
www.gladiatorgarageworks.com. Consumers in Canada can call 1-800-807-6777.
8
ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS REQUIRED
TO OBTAIN WARRANTY SERVICE.
Please have the following information available when you call the
GLADIATOR® WORKBENCH
WARRANTY
Customer eXperience Center:
■ Name, address and telephone number
■ Model number and serial number
■ A clear, detailed description of the problem
■ Proof of purchase including dealer or retailer name and address
IF YOU NEED SERVICE:
1. Before contacting us to arrange service, please determine whether your product requires repair. Some questions can be addressed without
service. Please take a few minutes to review the instructions or visit www.gladiatorgarageworks.com.
2. All warranty service is provided exclusively by our authorized Gladiator Service Providers. In the U.S. and Canada, direct all
requests for warranty service to:
Gladiator Customer eXperience Center
In the U.S.A., call 1-866-342-4089. In Canada, call 1-800-807-6777.
If outside the 50 United States or Canada, contact your authorized Gladiator dealer to determine whether another warranty applies.
ONE YEAR LIMITED WARRANTY
WHAT IS COVERED WHAT IS NOT COVERED
ONE YEAR LIMITED WARRANTY ON WOODEN TOP
For one year from the date of purchase, when this product is operated
and maintained according to the instructions attached to or furnished
with the product, Gladiator will replace or repair the defective product
or parts to correct defects in materials or workmanship.
LIFETIME LIMITED WARRANTY ON WORKBENCH METAL
SECTIONS
For the life of the product, when the Workbench is used and maintained
according to the instructions attached to or furnished with the product,
Gladiator will pay for repair or replacement of the defective product or
parts to correct defects in materials or workmanship.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
1. Service calls to correct the installation of any Gladiator products or
to instruct you on how to use or install them.
2. Damage resulting from improper handling or shipping of products,
or products damaged by accident, misuse, abuse, re, ood,
improper installation, acts of God, neglect, corrosion, modication
or mishandling.
3. Shipping or freight fees to deliver replacement products or to return
defective products.
4. Repairs or replacement when your product is used in other than
normal, single-family household use, such as a commercial
environment or handled in any way inconsistent with the installation
instructions included with the product.
5. Cosmetic damage including scratches, dings, dents or cracks that
do not affect the structural or functional capability of the product.
6. Replacement parts or product for Gladiator products operated
outside the United States and Canada.
7. In Canada, travel or transportation expenses for customers who
reside in remote areas.
8. Any labor costs during the limited warranty period.
9. Damage resulting from improper loading beyond the specied
maximum weight capacity outlined in the assembly instructions
provided with the product.
10. Surfaces damaged due to chemical interaction resulting in
corrosion of paint or metal.
11. Any damage, splitting, checking, cracking or warping of the
wooden top past the rst year.
The cost of repair or replacement under these excluded
circumstances shall be borne by thecustomer.
IMPLIED WARRANTIES, INCLUDING TO THE EXTENT APPLICABLE WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE, ARE EXCLUDED TO THE EXTENT LEGALLY PERMISSIBLE. ANY IMPLIED WARRANTIES
THAT MAY BE IMPOSED BY LAW ARE LIMITED TO ONE YEAR, OR THE SHORTEST PERIOD ALLOWED BY LAW. SOME
STATES AND PROVINCES DO NOT ALLOW LIMITATIONS OR EXCLUSIONS ON HOW LONG AN IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE
TO STATE OR PROVINCE TO PROVINCE.
Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Gladiator dealer to determine if
another warranty applies.
If you need service, call the Gladiator Customer eXperience Center, 1-866-342-4089 (toll-free), from anywhere in the U.S.A. In
Canada, contact your Whirlpool Canada LP designated service company or call 1-800-807-6777.
In the United States, Gladiator means Whirlpool Corporation, Benton Harbor, Michigan 49022. In Canada, Gladiator means
Whirlpool Canada LP, Mississauga, ON L5N 3A7.
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your Workbench to
better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can nd this information on the model and serial
label located on the back of the product.
Dealer name______________________________________________
Address___________________________________________________
Phone number_____________________________________________
Model number_____________________________________________
Serial number _____________________________________________
Purchase date_____________________________________________
Loading...