Gladiator GARS484TEG Assembly Instructions
HEAVY DUTY STEEL RACK
W10893670A
SHELVING
Assembly Instructions
ESTANTERÍA DE ACERO DE
SERVICIO PESADO
Instrucciones de ensamblaje
RAYONNAGE EN ACIER
POUR CHARGES
LOURDES
Instructions d’assemblage
77
", 60", & 48"
Estantería de 77", 60" y 48" de ancho (se muestra la de 77")
Largeur de rayonnage de 77", 60" et 48" (image à 77")
Wide Rack Shelving (77" shown)
TABLE OF CONTENTS
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't
follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
RACK SHELVING SAFETY ..................................................................2
PARTS ...................................................................................................3
ASSEMBLY INSTRUCTIONS............................................................... 4
Shelving Use Requirements...............................................................4
ÍNDICE
SEGURIDAD DE LA ESTANTERÍA......................................................7
PIEZAS...................................................................................................7
INSTRUCCIONES DE ENSAMBLAJE.................................................9
Requisitos de uso de la estantería.....................................................9
Desempaque......................................................................................9
TABLE DES MATIÈRES
SÉCURITÉ DU RAYONNAGE EN ACIER..........................................12
PIÈCES ................................................................................................12
INSTRUCTIONS D’ASSEMBLAGE....................................................14
Spécifications d’utilisation du rayonnage........................................14
RACK SHELVING SAFETY
Unpack............................................................................................... 4
Assemble End Frames/Support Beams............................................ 4
Assemble Tie Channel Supports....................................................... 5
Complete Assembly .......................................................................... 5
WARRANTY..........................................................................................6
Ensamblaje de los marcos
extremos y las barras de apoyo........................................................ 9
Ensamblaje de los soportes acanalados de sujeción....................... 9
Complete el ensamblaje.................................................................. 10
GARANTÍA ...................................................................................... 11
Déballage......................................................................................... 14
Assemblage cadres latéraux/rails de support ................................ 14
Assemblage des profilés de renfort ................................................ 14
Terminer l’assemblage ....................................................................15
GARANTIE .......................................................................................... 15
This storage rack unit must be placed on a level surface.
NOTES:
■ Do not stand or climb on the unit.
2
■ Do not overload.
■ Evenly distribute the weight on each shelf, and keep the heaviest
loads on the bottom shelf.
PARTS
P1
P2
P3
P4
P1
P2
P3
P4
77" Wide Rack Shelving
60
P1—Wire shelves (4)
P2—Support beams (8)—4 in front, 4 in back
"
Wide Rack Shelving
P3—Tie channel supports (12 or 8)
P4—Welded-end frame assemblies (2)
3
48
P1
P2
P3
P4
WARNING
Excessive Weight Hazard
Use two or more people to move and assemble
shelving.
Failure to do so can result in back or other injury.
"
Wide Rack Shelving
P1—Wire shelves (4)
P2—Support beams (8)—4 in front, 4 in back
ASSEMBLY INSTRUCTIONS
P3—Tie channel supports (4)
P4—Welded-end frame assemblies (2)
Shelving Use Requirements
■ Intended for use in a garage.
■ 77
"
Wide Rack Shelf: Maximum weight limit is 2,000 lbs (907 kg)
for each shelf, not to exceed 8,000 lbs (3,628 kg) for the entire
shelving unit.
■ 60
"
Wide Rack Shelf: Maximum weight limit is 1,800 lbs (816 kg)
for each shelf, not to exceed 7,200 lbs (3,266 kg) for the entire
shelving unit.
■ 48
"
Wide Rack Shelf: Maximum weight limit is 1,500 lbs (680 kg)
for each shelf, not to exceed 6,000 lbs (2,722 kg) for the entire
shelving unit.
Unpack
NOTE: Use two or more people to move and assemble shelving.
1. Remove and verify the contents. See “Parts.”
2. Dispose of/recycle all packaging materials.
4
Assemble End Frames/Support Beams
■ No tools required.
IMPORTANT:
■ Use two or more people to move and assemble shelving.
■ Determine shelf spacing before assembly.
NOTE: It is recommended to equally space the shelves from top
to bottom of the shelving unit. See “End Frames/Support
Beams” illustration.
Attach Shelf Support Beams to Welded End Frames
1. Position the 2 welded end frames (P4) vertical with the foot end
of each frame at ground level and profile slots facing forward.
2. At the desired shelf location, align both of the support beam (P2)
end tabs with the inside triangular frame slots on the welded
frame (P4).
3. Press the beam tabs down to the bottom of the frame slot (2 tabs
for each end of the support beam). This will lock the support
beam (P2) to the end frame (P4).
NOTE: If the support beam (P2) end tabs become bent, adjust
the tabs back to their original shape.
4. Repeat for other end of the support beam (P2). Check that the
height is the same for both ends of the support beam and for the
front and back support beams of each shelf.
5. Repeat steps 1 through 4 for each support beam for all 4 shelf
locations.
NOTES:
■ Front and back beams need to be at the same height, or the
shelves will not assemble correctly.
■ It may be necessary to adjust the end clip tabs back to their
proper form if they have been mishandled.
Support Beam Orientation
End Frames/Support Beams
Tie Channel Rotated into Front and Back Support Beam
Rivet Inserted into Keyhole
P2—Support beams (8)
P4—Welded end frames (2)
Assemble Tie Channel Supports
This shelving unit is equipped with 1, 2, or 3 tie channel supports (P3)
for each shelf.
NOTES:
■ The tie channel supports (P3) provide load support and structural
integrity.
■ All tie channel supports (P3) must be assembled as shown in “Tie
Channel Support Assembly” illustration.
1. Rotate the tie channel support (P3) into the front and back
support beam (P2), aligning the tie channel rivet heads with the
matching large diameter hole of the support beam keyhole.
2. To insert the rivet head on the other side of the tie channel
support (P3), apply pressure to both sides of the tie channel
support (P3), squeezing the sides toward each other. Insert the
rivet head into the matching larger hole of the support beam
keyhole on the front and back support beam (P2). Release
pressure.
3. Check that the rivets are held behind the smaller hole of the
support beam keyholes.
4. Repeat steps 1 and 2 for each tie channel support.
Tie Channel Support Assembly
A. P3—Tie channel support
B. Rivet head
C. Support beam lower
flange with keyhole
Complete Assembly
1. Verify that all beams and tie channel supports are properly
assembled and tightened.
2. Place wire shelf (P1) on top of the tie channel supports (P3) for
each shelf.
3. Move shelving unit to final location.
5
Loading...