‘
EXTRA LARGE
GEARBOX CABINET
Assembly Instructions
ARMARIO EXTRA
GRANDE CON ESTANTES
PARA HERRAMIENTAS
Instrucciones de ensamblaje
TRÈS GRANDE
ARMOIRE À OUTILS
Instructions d'assemblage
TABLE OF CONTENTS/ÍNDICE/TABLE DES MATIÈRES
CABINET/LOCKER SAFETY ........................ 2
PARTS ............................................................2
ASSEMBLY INSTRUCTIONS........................ 3
ACCESSORIES .............................................. 5
WARRANTY ...................................................6
SEGURIDAD DEL ARMARIO .......................7
PIEZAS ............................................................7
INSTRUCCIONES DE ENSAMBLAJE ..........8
ACCESORIOS.............................................. 10
GARANTÍA ................................................... 11
SÉCURITÉ DE L’ARMOIRE.........................12
PIÈCES..........................................................12
INSTRUCTIONS D'ASSEMBLAGE .............13
ACCESSOIRES.............................................15
GARANTIE ....................................................16
ES TIEMPO DE VOLVER A PENSAR EN EL GARAGE.™
W10174899C
IT'S TIME TO RETHINK THE GARAGE.
LE GARAGE REPENSÉ.™
®
CABINET/LOCKER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
follow instructions.
can be killed or seriously injured if you don't
You
instructions.
follow
PARTS
P6
P1
P2
P5m
P5
P5m
P8
P8
P8
P8
P8
P8
P1
P7
F1
F2
F3c
F5
P3
P4
2
ASSEMBLY INSTRUCTIONS
P1
P2
Cabinet Use Requirements
■ Intended for use in a garage.
■ Maximum weight limit is 50 lbs (22.7 kg) for each shelf.
■ Maximum weight limit is 250 lbs (113.6 kg) for the cabinet.
Unpack Cabinet Parts
1. Remove and verify the contents. Contents include a hex key, a
key, and the parts and fasteners shown in “Parts.”
2. Dispose of/recycle all packaging materials.
7. Align the holes and attach the bottom (P3) to the sides (P1) using
six Hex-head bolts (F1) and two ⁵⁄₁₆"
as shown. Do not tighten completely.
flange nuts (F2) for each side
P3
P1
Assemble Cabinet
F1 F2
F1
⁵⁄₁₆
" Hex-head bolt (24)
F2
⁵⁄₁₆
" Flange nut (8)
Gather the required tools before starting installation.
Tools Needed:
■ ¹⁄₂" Wrench
■ ³⁄₈" Wrench
Tool s Sup p lie d:
■ Hex key ■ Key
■ Phillips screwdriver
■ Level
WARNING
Excessive Weight Hazard
Use two or more people to move, assemble or install
cabinet.
Failure to do so can result in back or other injury.
IMPORTANT:
■ Two people may be required to complete the assembly.
■ As you assemble the cabinet, make sure the edges with the
holes are facing up.
■ If you are assembling the cabinet on the floor, fasten the eight
front corner bolts, two at each corner, after you stand the cabinet
upright.
1. Place side panel (P1) on a flat, firm surface so that the edge with
the holes is facing up as shown.
2. Insert the cabinet top (P2) between the edges of side panel (P1).
NOTE: Make sure the edges with the holes are facing up.
3. Align the holes and attach the top (P2) to side panel (P1) using
six Hex-head bolts (F1) and two ⁵⁄₁₆"
Do not tighten completely.
4. Position the other side panel (P1) so that the top (P2) is between
the edges of side panel (P1).
5. Align the holes and attach the top (P2) to the side (P1) using six
Hex-head bolts (F1) and two ⁵⁄₁₆"
not tighten completely.
6. Insert the cabinet bottom (P3) between the edges of the side
panels (P1).
NOTE: Make sure the edges with the holes are facing up.
flange nuts (F2) as shown.
flange nuts (F2) as shown. Do
P1
P2
Attach Back Panels
F3c
Phillips-head screw (40)
IMPORTANT:
■ Attach the back panels (P8) starting at the top of the cabinet and
working down to the cabinet bottom. Each consecutive back
panel will overlap the panel above.
■ Do not completely tighten the screws until all back panels are in
place.
■ The back panels, top and bottom, may have additional holes that
are not used.
1. Align the first back panel (P8) with the holes in the cabinet top.
Using Phillips-head screws (F3c), attach the panel (P8) to the
cabinet top and sides.
2. Overlap the bottom of the first back panel (P8) with the top of the
second back panel (P8) as shown. Using Phillips-head screws,
fasten back panel (P8) to the cabinet sides.
A. Cabinet top
3. Repeat Step 2 to attach the four remaining back panels to the
cabinet sides.
3
4. Using two Phillips-head screws, attach each back panel to the
A
panel above.
NOTE: Using three Phillips-head screws, attach the last back
panel (P8) to the cabinet bottom (P3).
5. Completely tighten all back panel screws starting with the sides
and continuing with the top, middle and bottom.
6. Using the hex key (provided), completely tighten all 24 cabinet
bolts and nuts.
P8
P8
P8
P8
P8
P1
P8
P1
P3
Install Shelves
F3c F5
F3cF5Phillips-head screw (12)
Small flange nut (12)
IMPORTANT: Use the pair of holes located in the middle of the
cabinet sides to install a center shelf without the magnet (P5), so the
doors will lock. The other two shelves with magnet (P5m) may be
installed where desired.
1. Place a shelf (P5) so that the holes in the ends are aligned with
the pair of holes in the middle of the cabinet sides.
NOTE: Make sure the holes in the long edge of the shelf are
facing out.
2. Using two screws and nuts per side, fasten the shelf (P5) to the
sides (P1).
P2
A
A. Cabinet bottom
Install Leveling Legs
1. Place the cabinet on its side.
2. Screw a leveling leg (P4) into each of the four rivet nuts located at
the corners of the cabinet as shown.
P1
P4
P8
P8
A. Leveling legs
P3
P8
P8
P1
P1
P8
P5
A
P8
P8
P3
A. Middle pair of holes in cabinet side
3. Determine where you want to place the other two shelves (P5m).
Align the holes in the shelf ends with the holes in the cabinet
side.
NOTE: Make sure the magnets on the long edge of the shelf are
facing the cabinet front.
4. Using two screws and nuts per side, fasten the shelves (P5m) to
the cabinet sides (P1). Completely tighten the nuts.
3. Stand the cabinet upright.
4. If you have not already done so, fasten the two bolts at each
front corner, of the cabinet frame. Completely tighten all the
cabinet bolts and nuts.
4
Install Doors
F3c
Phillips-head screw (12)
IMPORTANT:
■ The door with the lock assembly (P7) should be installed on the
right-hand side of the cabinet.
■ The door hinges are designed with keyhole slots at the top and
bottom so the door will hang on the cabinet while you are
fastening the screws.
1. Start Phillips-head screws (F3c) in both the top and bottom holes
on each side of the cabinet.
2. Hang the right-hand side door (P7) from the top and bottom
screws, and hand tighten.
3. Insert the middle four screws through the door hinge into the
cabinet and hand tighten.
P2
P5m
P1
P5
A
P7
Complete Assembly
1. Make sure there is a bolt or screw in each hole of the cabinet
frame.
NOTE: The back panels, top and bottom, may have additional
holes that are not used.
2. Move the cabinet to its final location.
3. Place a level on an inside shelf, and if necessary, level the
cabinet by adjusting the height of the leveling legs. Turn to the
left to raise or to the right to lower the leveling leg.
4. If the doors are not aligned, loosen all the screws attaching the
door hinge to the cabinet.
5. Adjust door to the desired height, and fully tighten the screws.
ACCESSORIES
To order accessories, call 1-866-342-4089 and ask for the accessory
part number listed below or contact your authorized Gladiator
GarageWorks dealer. In Canada, call 1-800-807-6777.
Mounting Bracket Kit - Allows the cabinet to be mounted on
Gladiator
Order Part # GABK362PSS
®
Garageworks GearWall® panels or GearTrack® channels.
®
P5m
P3
A. Phillips-head screws
4. Repeat steps 2 and 3 to attach the left-hand door (P6).
5. Align the doors and completely tighten the screws.
5
Loading...