Gladiator GAJG36GRDG User Manual [en, fr, es]

PREMIER JUMBO CABINET

W10130911D

IT'S TIME TO RETHINK THE GARAGE.

ES TIEMPO DE VOLVER A PENSAR EN EL GARAGE.™

LE GARAGE REPENSÉ.™

(GAJG36GRDG)

Assembly Instructions

ARMARIO GIGANTE DE ALTA CALIDAD (GAJG36GRDG)

Instrucciones de ensamblaje

GRANDE ARMOIRE PREMIER JUMBO (GAJG36GRDG)

Instructions d’assemblage

TABLE OF CONTENTS/ÍNDICE/TABLE DES MATIÈRES

CABINET/LOCKER SAFETY .......................2

PARTS ...........................................................3

ASSEMBLY INSTRUCTIONS.......................4

Cabinet Use Requirements........................4

Unpack Cabinet Parts................................4

Assemble Cabinet......................................4

Attach Back Panels....................................4

Install Leveling Legs...................................5

Install Shelves ............................................5

Install Doors ...............................................6

Complete Assembly...................................6

ACCESSORIES .............................................6

WARRANTY ..................................................7

SEGURIDAD DEL ARMARIO ...................... 8

PIEZAS ..........................................................9

INSTRUCCIONES DE ENSAMBLAJE ......10

Requisitos de uso del armario.................10

Desempaque las piezas del armario .......10

Ensamble el armario ................................10

Fije los paneles posteriores ..................... 10

Instalación de las patas niveladoras .......11

Instalación de los estantes ......................11

Instalación de las puertas........................12

Complete el ensamblaje ..........................12

ACCESORIOS.............................................13

GARANTÍA ..................................................13

SÉCURITÉ DE L’ARMOIRE....................... 14

PIÈCES........................................................15

INSTRUCTIONS D’ASSEMBLAGE ........... 16

Spécifications d’utilisation de l’armoire ..16

Déballage des pièces de l’armoire .......... 16

Assemblage de l’armoire......................... 16

Fixation des panneaux arrière ................. 16

Installation des pieds de réglage

de l’aplomb.............................................. 17

Installation des étagères.......................... 17

Installation des portes .............................18

Fin de l’assemblage................................. 18

ACCESSOIRES........................................... 19

GARANTIE .................................................. 19

CABINET/LOCKER SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

AAA

BBB

CCC

P5mr

DDD

EEE

PARTS

F1x F1 F2 F3c

ASSEMBLY INSTRUCTIONS

WARNING

Excessive Weight Hazard

Use two or more people to move, assemble or install cabinet.

Failure to do so can result in back or other injury.

Cabinet Use Requirements

■ Intended for use in a garage.

■ Maximum weight limit is 50 lbs (22.7 kg) for each shelf.

■ Maximum weight limit is 300 lbs (136 kg) for the cabinet.

Unpack Cabinet Parts

1. Remove and verify the contents. Contents include a hex key, a

key, and the parts and fasteners shown in “Parts.”

2. Dispose of/recycle all packaging materials.

Assemble Cabinet

F1 F2

⁵⁄₁₆

" hex-head bolt (28)

⁵⁄₁₆

" flange nut (12)

Gather the required tools before starting installation.

Tools Needed

■ ¹⁄₂" wrench

■ Phillips screwdriver

Tools Supplied

■ Hex key ■ Key

■ Level

6. Insert the cabinet bottom (P3) between the edges of the side

panels (P1).

NOTE: Make sure the edges with the holes are facing up.

7. Align the holes and attach the bottom (P3) to the sides (P1) using

hex-head bolts (F1) and the three ⁵⁄₁₆" flange nuts (F2). Do not tighten completely.

Attach Back Panels

IMPORTANT:

■ Two people may be required to complete the assembly.

■ As you assemble the cabinet, make sure the edges with the

holes are facing up.

■ If you are assembling the cabinet on the floor, fasten the eight

front corner bolts, two at each corner, after you stand the cabinet upright.

1. Place side panel (P1) on a flat, firm surface so that the edge with

the holes is facing up as shown.

2. Insert the cabinet top (P2) between the edges of side panel (P1). NOTE: Make sure the edges with the holes are facing up.

3. Align the holes and attach the top (P2) to side panel (P1) using

hex-head bolts (F1) and the three ⁵⁄₁₆" Do not tighten completely.

4. Position the other side panel (P1) so that the top (P2) is between the edges of side panel (P1).

5. Align the holes and attach the top (P2) to the side (P1) using hexhead bolts (F1) and the three ⁵⁄₁₆" not tighten completely.

flange nuts (F2) as shown.

flange nuts (F2) as shown. Do

F3c

Phillips-head screw (34)

IMPORTANT:

■ Attach the back panels starting at the top of the cabinet with

back panel (AAA) and working down to the cabinet bottom. Each back panel will overlap the panel below.

■ Do not completely tighten the screws until all back panels are in

place.

1. Align back panel (AAA) with the holes in the cabinet top. Using

Phillips-head screws (F3c), attach back panel (AAA) to the cabinet top and sides.

2. Slide the top of back panel (BBB) under the bottom of back panel

(AAA). Using Phillips-head screws, fasten back panel (BBB) to the cabinet sides.

3. Repeat Step 2 for the remaining back panels ending with back

panel (EEE).

4. Using Phillips-head screws, attach each back panel to the panel

below. NOTE: Using Phillips-head screws, attach panel (EEE) to the

cabinet bottom (P3).

5. Completely tighten all back panel screws starting with the sides

and continuing with the top, middle and bottom.

6. Using the hex key (provided), completely tighten all cabinet bolts

and nuts.

1. Place a shelf (P5mr) so that the 2 tabs in the shelf ends are

AAA

BBB

CCC

DDD

EEE

P5mr

aligned with the pair of slots in the middle of the cabinet sides.

Install Leveling Legs

(optional)

IMPORTANT: If you are going to install the cabinet on Gladiator GearWall leveling legs.

1. Place the cabinet on its side.

2. Screw a leveling leg (P4) into each of the four rivet nuts located at

3. Stand the cabinet upright.

4. If you have not already done so, fasten the two bolts at each

IMPORTANT:

■ The shelves are supported by the metal slots on the cabinet

■ Make sure the magnet in the right of each long shelf edge is

panels or GearTrack® channels, you do not need to install

the corners of the cabinet as shown.

front corner, of the cabinet frame. Completely tighten all of the cabinet bolts and nuts.

sides.

facing out.

A. Leveling legs

Install Shelves

2. Tilt the shelf so that one end is higher than the other as shown.

A. Push down. B. Lift up.

3. Insert the shelf into the cabinet so that the higher end is directly

above the desired slots and push the shelf down into place behind the side slots. Raise the lower end so it is directly above the desired slots and push the shelf down.

NOTE: You may need to slightly bend the shelf tabs outward for the tabs to engage in the slots. Make sure the shelf tabs are in place behind all the slots, as shown.

A. Cabinet slot B. Shelf tab

4. Repeat steps 2 and 3.

P5mr

NOTE: Make sure the magnet in the right of each long shelf edge is facing out.

3. Insert the middle 4 screws through the door hinge into the

cabinet and hand tighten.

A. Magnet facing outward

Adjust the Shelves

1. Lift up on the underside of the shelf until the shelf tabs are free of

the cabinet slots.

2. Tilt the shelf up to reposition it within the cabinet or to remove it from the cabinet.

Install Doors

F3c

Phillips-head screw (12)

IMPORTANT:

■ The door with the lock assembly (P7) should be installed on the

right-hand side of the cabinet.

■ The door hinges are designed with keyhole slots at the top and

1. Start Phillips-head screws (F3c) in both the top and bottom holes

2. Hang the right-hand side door (P7) from the top and bottom

bottom so the door will hang on the cabinet while you are fastening the screws.

on each side of the cabinet.

screws, and hand tighten.

A. Phillips-head screws

4. Repeat steps 2 and 3 to attach the left-hand door (P6).

5. Align the doors and completely tighten the door screws.

Complete Assembly

1. Make sure there is a bolt or screw in each hole of the cabinet

frame.

2. Move the cabinet to its final location.

3. Place a level on an inside shelf, and if necessary, level the

cabinet by adjusting the height of the leveling legs. Turn to the left to raise or to the right to lower the leveling leg.

4. If the doors are not aligned, loosen all the screws attaching the

door hinge to the cabinet.

5. Adjust door to the desired height, and fully tighten the screws.

ACCESSORIES

To order accessories, call 1-866-342-4089 and ask for the accessory part number listed below or contact your authorized Gladiator GarageWorks dealer. In Canada, call 1-800-807-6777.

Mounting Bracket Kit - Allows the cabinet to be mounted on Gladiator

Order Part # GABK362PSS

Garageworks GearWall® panels or GearTrack® channels.

+ 14 hidden pages

Gladiator GAJG36GRDG User Manual [en, fr, es]

Specifications and Main Features

Frequently Asked Questions

User Manual