Gladiator GAJG36FDYG, GAJG36FDZW, GAJG36FDKSG Owner's Manual
Model/Modèle/Modelo:
GAJG36FDYG - Hammered Granite/Silver Tread
GAJG36FDZW - Hammered White/Gray Slate
GAJG36FDKSG - Hammered Granite/Hammered Granite
PREMIER JUMBO
CABINET
Assembly Instructions
GRANDE ARMOIRE
(PREMIER JUMBO)
Instructions d’assemblage
ARMARIO GIGANTE DE
ALTA CALIDAD
Instrucciones de ensamblaje
TABLE OF CONTENTS/TABLE DES MATIÈRES/ÍNDICE
CABINET/LOCKER SAFETY ..............2
PARTS .................................................. 2
ASSEMBLY INSTRUCTIONS ..............3
Tools and Parts .................................3
Cabinet Use Requirements ............... 3
Unpack Cabinet Parts .......................3
Assemble Cabinet ............................. 3
Complete Assembly .......................... 6
INSTALLATION INSTRUCTIONS ........ 7
ACCESSORIES .................................... 8
WARRANTY ......................................... 9
In U.S.A. call: 1-866-342-4089
W11476042B
Aux États-Unis, composez le: 1866342-4089
En los EE.UU., llame al: 1-866-342-4089
SÉCURITÉ DE L’ARMOIRE ..............10
PIÈCES ..............................................10
INSTRUCTIONS D'ASSEMBLAGE ... 11
Outillage Et Pièces .......................... 11
Spécications d'utilisation de
l'armoire .......................................... 11
Déballage des pièces de l'armoire..11
Assemblage de l'armoire ................11
Fin de l’assemblage ........................ 14
INSTRUCTIONS D'INSTALLATION ..15
ACCESSOIRES .................................. 16
GARANTIE ......................................... 17
In Canada call: 1-800-807-6777
Au Canada, composez le: 1800807-6777
En Canadá, llame al: 1-800-807-6777
SEGURIDAD DEL ARMARIO ............ 18
PIEZAS ...............................................18
INSTRUCCIONES DE
ENSAMBLAJE ................................... 19
Herramientas Y Piezas ....................19
Requisitos de uso del armario ........ 19
Desempaque las piezas del
armario ............................................ 19
Ensamble el armario .......................19
Complete el ensamblaje .................22
INSTRUCCIONES DE
INSTALACIÓN ...................................23
ACCESORIOS ...................................24
GARANTÍA ......................................... 25
www.gladiatorgarageworks.com
www.gladiatorgarageworks.ca
1
CABINET/LOCKER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
follow instructions.
You
can be killed or seriously injured if you don't
instructions.
follow
PARTS
P6 P1
P2
P5mr
P5ml
P5mr
P3
AAA
BBB
P8
F1
P8
F2
CCC
F3
P8
DDD
P1
P7
F7
EEE
P4
2
F8
ASSEMBLY INSTRUCTIONS
Tools and Parts
Gather the required tools and parts before starting installation.
Tools Needed:
■ 1/2" Wrench ■ Level
■ Phillips screwdriver
Tools Supplied:
■ Hex key
■ Key
Cabinet Use Requirements
■ Intended for use in a garage.
■ Maximum weight limit is 50 lbs (22.7 kg) for each shelf.
■ Maximum weight limit is 300 lbs (136 kg) for the cabinet.
Unpack the Cabinet
1. Remove and verify the contents. Contents include a hex key, a
key, and the parts and fasteners shown in “Parts.”
2. Dispose of/recycle all packaging materials.
Assemble Cabinet
WARNING
Excessive Weight Hazard
Use two or more people to move, assemble or install
cabinet.
Failure to do so can result in back or other injury.
IMPORTANT: Two people may be required to complete the
assembly. As you assemble the cabinet, make sure the edges
with the holes are facing up. If you are assembling the cabinet on
the oor, fasten the eight front corner bolts, two at each corner,
after you stand the cabinet upright.
1. Assemble Cabinet
F1
F1 5/16" hex-head bolt (28)
F2 5/16" ange nut (12)
F2
P3
P1
P2
P2
Place side panel (P1) on a at, rm surface so that the edge
with the holes is facing up, as shown. Insert the cabinet top (P2)
between the edges of side panel (P1).
NOTE: Make sure the edges with the holes are facing up.
Align the holes and attach the top (P2) to side panel (P1) using
hex-head bolts (F1) and the three 5/16" ange nuts (F2), as
shown. Do not tighten completely. Position the other side panel
(P1) so that the top (P2) is between the edges of side panel (P1).
Align the holes and attach the top (P2) to the side (P1) using
hexhead bolts (F1) and the three 5/16" ange nuts (F2), as shown.
Do not tighten completely. Insert the cabinet bottom (P3) between
the edges of the side panels (P1).
NOTE: Make sure the edges with the holes are facing up.
Align the holes and attach the bottom (P3) to the sides (P1) using
hex-head bolts (F1) and the three 5/16" ange nuts (F2). Do not
tighten completely.
P1
P1
3
2. Attach Back Panels
3. Install Leveling Legs (optional)
AAA
F3c Phillips-head screw (34)
F3c
P1
CCC
DDD
EEE
P1
P3
BBB
AAA
P1
P4
Leveling feet (4)
P1
P4
P2
EEE
P3
A
A. Leveling legs
IMPORTANT: Attach the back panels starting at the top of the
cabinet with back panel (AAA) and working down to the cabinet
bottom. Each back panel will overlap the panel below. Do not
completely tighten the screws until all back panels are in place.
Align back panel (AAA) with the holes in the cabinet top. Using
Phillips-head screws (F3c), attach back panel (AAA) to the cabinet
top and sides. Slide the top of back panel (BBB) under the bottom
of back panel (AAA). Using Phillips-head screws, fasten back
panel (BBB) to the cabinet sides. Repeat Step 2 for the remaining
back panels ending with back panel (EEE). Using Phillips-head
screws, attach each back panel to the panel below.
NOTE: Using Phillips-head screws, attach panel (EEE) to the
cabinet bottom (P3).
Completely tighten all back panel screws starting with the sides
and continuing with the top, middle and bottom. Using the hex
key (provided), completely tighten all cabinet bolts and nuts.
4
IMPORTANT: If you are going to install the cabinet on Gladiator®
GearWall® panels or GearTrack® channels, you do not need to
install leveling legs.
Place the cabinet on its side. Screw a leveling leg (P4) into each
of the four rivet nuts located at the corners of the cabinet, as
shown. Stand the cabinet upright. If you have not already done
so, fasten the two bolts at each front corner of the cabinet frame.
Completely tighten all of the cabinet bolts and nuts.
P2
4b. Install Shelves
A
P1
P1
P5ml
A
P3
A. Middle pair of slots in cabinet side
IMPORTANT: Use the pair of slots located in the middle of the
cabinet sides to install a center shelf (P5ml). The magnet should
be on the left-hand side and facing out when installed, so that the
door closure will make contact with the shelf, and the door will
lock. The other two shelves may be installed where desired. The
shelves are supported by the metal slots on the cabinet sides.
Make sure that the shelf (P5ml) magnet is visible on the left-hand
side and facing out, as shown.
Place a shelf (P5ml) so that the two tabs in the shelf ends are
aligned with the pair of slots in the middle of the cabinet sides.
B
A. Push down
B. Lift up
A
B
A. Cabinet slot
B. Shelf tab
Tilt the shelf so that one end is higher than the other, as shown.
Insert the shelf into the cabinet so that the higher end is directly
above the desired slots, and then push the shelf down into place
behind the side slots. Raise the lower end so it is directly above
the desired slots, and then push the shelf down.
NOTE: You may need to slightly bend the shelf tabs outward for
the tabs to engage in the slots. Make sure the shelf tabs are in
place behind all the slots, as shown.
5
4c. Install Shelves 5. Install Doors
P2
P5mr
P1
P1
P5ml
A
P5mr
P3
A. Magnet facing outward
Repeat steps 2 and 3 for the remaining two shelves (P5mr). The
magnet for shelves (P5mr) is located on the right-hand side and
facing out, as shown below.
NOTE: Make sure the magnet on the right side of each long shelf
edge is facing out.
Adjust the Shelves
1. Lift up on the underside of the shelf until the shelf tabs are free
of the cabinet slots.
2. Tilt the shelf up to reposition it within the cabinet or to remove
it from the cabinet.
F3c Phillips-head screw (12)
F3c
P2
P5mr
P5ml
A
P5mr
P3
IMPORTANT: The door with the lock assembly (P7) should be
installed on the right-hand side of the cabinet. The door hinges
are designed with keyhole slots at the top and bottom so the door
will hang on the cabinet while you are fastening the screws.
Start Phillips-head screws (F3c) in both the top and bottom holes
on each side of the cabinet. Hang the right-hand side door (P7)
from the top and bottom screws, and hand tighten. Insert the
middle four screws through the door hinge into the cabinet and
hand tighten. Repeat steps 2 and 3 to attach the left-hand door
(P6). Align the doors and completely tighten the door screws.
P1
P7
A. Phillips-head screws
Complete Assembly
1. Make sure there is a bolt or screw in each hole of the cabinet frame.
2. Move the cabinet to its nal location.
3. Place a level on an inside shelf, and if necessary, level the cabinet by adjusting the height of the leveling legs. Turn to the left to raise
or to the right to lower the leveling leg.
4. If the doors are not aligned, loosen all the screws attaching the door hinge to the cabinet.
5. Adjust door to the desired height, and fully tighten the screws.
6
INSTALLATION INSTRUCTIONS
WARNING
Excessive Weight Hazard
Use two or more people to move, assemble or install
cabinet.
Failure to do so can result in back or other injury.
1. Install GearWall
®
panels or
GearTrack® channels
18" (46 cm)
IMPORTANT: Gladiator brand Premier Jumbo cabinet is designed
to be installed on Gladiator® GearWall® panels or GearTrack®
channels. If GearTrack® channels will be used to support the
Gladiator® Premier Jumbo GearBox cabinet, you must use three
channels installed 18" (45.72 cm) apart. Be sure the GearWall®
panels or GearTrack® channels are installed with mounting screws
in every slot and at every stud location with a maximum of
24" (60.96 cm) horizontally between screws.
2a. Attach Mounting Brackets
F8F7 F2
F7 Carriage-head bolt (9)
F8 Washer (9)
P2
P8
AAA
BBB
F2 5/16" ange nut (9)
AAA
P1
P1
P8
A
A. Bracket rims pointing down
IMPORTANT: There are slots in back panels (AAA, CCC, and
DDD) to attach the mounting brackets (P8).
With the mounting bracket rim pointing down, align the three
bracket holes with the slots in back panel (AAA), as shown.
Working from the back, insert carriage bolts (F7) through the
bracket and into top back panel (AAA). Working from the cabinet
interior, fasten each bolt with a washer (F8) and a ange nut (F2).
Fully tighten the bolts.
7
2b. Attach Mounting Brackets
3. Mount the Cabinet to GearWall
Panels or GearTrack® Channel
A
B
®
Repeat steps 1 and 2 to attach the center and bottom mounting
brackets (P8) to the back of the cabinet.
NOTE: Hand tighten the nuts attaching the center and bottom
brackets. These brackets will need to be adjusted to mount the
cabinet on the wall.
A. Bracket rim B. Mounting bracket
fully engaged
NOTE: The three nuts on the center and bottom mounting
brackets must be loose enough to allow the brackets to move in
the slots.
Close the cabinet doors. Determine cabinet mounting location
on GearWall® panels or GearTrack® channel. Using two or more
people, engage the top bracket (P8) into the slots by lifting up,
pushing toward the wall and lowering the bracket rims into the
slots, as shown. Make sure the top bracket is fully engaged in the
slots, as shown. Open the cabinet doors. From inside the cabinet,
grasp the bolts in the center bracket and adjust the bracket
until it aligns with the slot in the GearWall® panels or GearTrack®
channels. Push the cabinet toward the wall and lower the center
mounting bracket into the slots. Make sure the center bracket
(P8) is fully engaged in the slot, as shown. Repeat for the bottom
bracket (P8). Using a 1/2" wrench, fully tighten the nuts attaching
the center and bottom brackets.
ACCESSORIES
The Gladiator® GearRod accessory provides a hanging solution for heavy outdoor gear and other seasonal items, freeing up space
in your household closets for everyday items. It attaches to any of the adjustable shelves or to the top of the cabinet. The Gladiator®
GearRod holds up to 100 lbs of seasonal clothing and outdoor gear wear.
To order accessories, call 1-866-342-4089 and ask for the accessory part number listed below or contact your authorized Gladiator
brand dealer. In Canada, call 1-800-807-6777.
GearRod Accessory
Order Part # GAAC36GRDSS
8
For warranty information:
In the U.S.A. call 1-866-342-4089 or visit our website at
www.gladiatorgarageworks.com
In Canada call 1-800-807-6777 or visit our website at
www.gladiatorgarageworks.ca
WARRANTY
9
Loading...