STEEL MODULAR
THREE-DRAWER CABINET
Assembly Instructions
ARMARIO MODULAR DE ACERO CON TRES CAJONES
Instrucciones de ensamblaje
ARMOIRE MODULAIRE EN ACIER TROIS TIROIRS
Instructions d'assemblage
TABLE OF CONTENTS/ÍNDICE/TABLE DES MATIÈRES
CABINET/LOCKER SAFETY .......................1
PARTS ..........................................................2
ASSEMBLY INSTRUCTIONS.......................2
ACCESSORIES .............................................5
WARRANTY ..................................................6
SEGURIDAD DEL ARMARIO ..................... 7
PIEZAS .........................................................7
INSTRUCCIONES DE ENSAMBLAJE ........8
ACCESORIOS.............................................10
GARANTÍA ..................................................11
SÉCURITÉ DE L’ARMOIRE....................... 12
PIÈCES ....................................................... 12
INSTRUCTIONS D'ASSEMBLAGE ........... 13
ACCESSOIRES........................................... 15
GARANTIE .................................................. 16
CABINET/LOCKER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
IT'S TIME TO RETHINK THE GARAGE.
ES TIEMPO DE VOLVER A PENSAR EN EL GARAGE.™
LE GARAGE REPENSÉ.™
follow instructions.
can be killed or seriously injured if you don't
You
instructions.
®
follow
W10343070B
P1
PARTS
P2
P5
P7
P7
P4
P3
P6
P7
P7
F1 F2 F3c
D5
D1
D4
D2
D3
ASSEMBLY INSTRUCTIONS
Cabinet Use Requirements
■ Intended for use in a garage.
■ Maximum weight limit is 30 lbs (13.6 kg) for each drawer.
■ Maximum weight limit is 300 lbs (136 kg) for the cabinet.
Unpack Cabinet Parts
1. Remove and verify the contents. Contents include a hex key, and
the parts and fasteners shown in “Parts.”
2. Dispose of/recycle all packaging materials.
2
Assemble Cabinet
F1 F2
F1
⁵⁄₁₆
" Hex-head bolt (24)
F2
⁵⁄₁₆
" Flange nut (8)
Gather the required tools before starting installation.
Tools Needed:
A
■ ¹⁄₂" Wrench
■ ³⁄₈" Wrench
■ Phillips screwdriver
Tools Supplied:
■ Hex key
■ Pliers
■ Level
■ Tape measure
8. Square the cabinet frame. The measurements from corner to
corner should be equal distance.
P4
P1
WARNING
Excessive Weight Hazard
Use two or more people to move, assemble or install
cabinet.
Failure to do so can result in back or other injury.
IMPORTANT:
■ Two people may be required to complete the assembly.
■ As you assemble the cabinet, make sure the edges with the
holes are facing up.
■ If you are assembling the cabinet on the floor, fasten the eight
front corner bolts, two at each corner, after you stand the cabinet
upright.
1. Place side panel (P1) on a flat, firm surface so that the edge with
the holes is facing up as shown.
2. Insert the cabinet top (P2) between the edges of side panel (P1).
NOTE: Make sure the edges with the holes are facing up.
3. Align the holes and attach the top (P2) to side panel (P1) using
six internal hex-head bolts (F1) and two ⁵⁄₁₆"
the two middle holes only, as shown. Do not tighten completely.
4. Position side panel (P3) so that the top (P2) is between the edges
of side panel (P3).
5. Align the holes and attach the top (P2) to the side (P3) using six
internal hex-head bolts (F1) and two ⁵⁄₁₆"
two middle holes only, as shown. Do not tighten completely.
6. Insert cabinet bottom (P4) between the edges of side panels
(P1 and P3).
NOTE: Make sure the edges with the holes are facing up and that
the threaded posts are standing up on the inside of the unit as
shown.
7. Align the holes and attach the bottom (P4) to the side panels
(P1 and P3) using12 internal hex-head bolts (F1) and four ⁵⁄₁₆"
flange nuts (F2), for the four middle holes only, as shown.
flange nuts (F2), for
flange nuts (F2), for the
P3
P2
9. Using the hex key (provided), completely tighten the bolts.
Measure the frame again to make sure it is still square.
Install Leveling Legs or Casters
The Gladiator® Modular Cabinet is designed to be either stationary or
to roll on casters.
IMPORTANT: If you decide to install the casters on the cabinet, see
the installation instructions included with the caster kit (provided).
To install leveling legs:
1. Place the cabinet on its side.
2. Screw a leveling leg (P7) into each of the four rivet nuts located at
the corners of the cabinet as shown.
P1
P7
P6
P4
P1
P2
A. Leveling legs
3. Stand the cabinet upright.
4. If you have not already, fasten the two bolts at each front corner,
P4
of the cabinet frame. Completely tighten all the cabinet bolts and
nuts.
P3
P2
P3
3
Assemble Drawers
D3
D4
F3c
F3c Phillips-head screw (45-black)
IMPORTANT: When assembling the drawer, make sure the drawer
sides (D1) and (D3) are positioned so that the glides are near the top
and facing outward.
1. Place the drawer bottom (D4) on a flat, firm surface, so that the
tabs are pointing up.
NOTE: The long side with holes is the front edge of the drawer
bottom.
5. Lay the drawer back (D2) flat on top of the drawer bottom, so
that the tabs are alternating. Slowly lift up on the drawer back
until it is upright and the tabs are interlocked.
6. Working from inside the drawer, insert the six screws (3 on each
side) through the drawer back (D2) and into the flanges of drawer
sides (D1 and D3).
NOTE: To allow for adjustment when inserting the drawers into
the cabinet do not completely tighten the screws.
D2
D1
D4
2. Lay drawer side (D3) flat on top of the drawer bottom (D4), so
that the tabs are alternating.
3. Slowly lift up on the drawer side (D3) until the side is upright and
the tabs are interlocked as shown.
D4
D3
D4
D3
D2
D1
A
7. Stand the drawer on its back (D2) so that the drawer bottom (D4)
is facing you.
8. Position the drawer front (D5), so that its side flanges are inside
the drawer sides (D1 and D3), and its bottom flange is under the
drawer bottom (D4).
D5
D1
D4
4. Repeat steps 2 and 3 to assemble the opposite drawer side (D1).
D1
D4
4
D3
9. Using nine Phillips-head screws (F3c), fasten the drawer front to
each side and the bottom (3 screws each).
D2
A
D3
D5
D1
B
A. Drawer glide lever
B. Phillips-head screws (F3c)
10. Repeat steps 1 through 8 to assemble the remaining two
drawers.
11. Before you insert the drawers into the cabinet, make sure the
bearing carriages on the cabinet slides are at the front of the
cabinet.
12. Align the drawer glides with the slides on the inside of the
cabinet. Insert the drawer glides into the slides and push the
drawer into the cabinet.
NOTE: If the drawer glide is not correctly aligned with the cabinet
slide, the drawer may become lodged in the cabinet. Facing the
cabinet, press down on the lever located on the right-hand
drawer glide while pressing up on the lever located on the lefthand drawer glide to release the drawer.
13. Once each drawer is in place, work from inside each drawer to
completely tighten the six screws (3 on each side) attaching the
drawer back (D2).
Attach Lower Back Panel
Attach Upper Back Panel
F3c
F3c Phillips-head screw (9 - black)
1. Align back panel (P5) with the holes in the top (P2). Using
Phillips-head screws (F3c), attach back panel (P5) to the top (P2)
and sides (P1 and P3) as shown. Do not tighten screws
completely.
NOTE: Back panel (P5) will slightly overlap back panel (P6).
2. Using Phillips-head screws (F3c), attach the upper back panel
(P5) to the lower back panel (P6) as shown.
3. Completely tighten all back panel screws starting with the sides
and continuing with the top, middle, and bottom.
F3c
F3c Phillips-head screw (7 - black)
1. Using Phillips-head screws (F3c), attach the lower back panel
(P6) to the bottom (P4) and sides (P1 and P3) as shown. Tighten
screws completely.
2. Using the hex key (provided), completely tighten all the cabinet
bolts and nuts.
P2
D2
P1
P6
D2
D2
P2
D2
P5
P1
P6
Complete the Assembly
1. Make sure there is a bolt or screw in each hole of the cabinet
frame.
NOTE: Not all the holes in the cabinet side panels will be used.
2. Move the cabinet to its final location.
ACCESSORIES
To order accessories, call 1-866-342-4089 and ask for the accessory
part number listed below or contact your authorized Gladiator brand
dealer. In Canada, call 1-800-807-6777.
Caster Kit
Order Part # GACK04KDSX
VersaTop™ Work Surface
Order Part # GAVT18SPSX
Modular Bamboo top
Order Part # GAAC28BAYX
5
Loading...