Glacier bay PPSPAGLC30DM User Manual
Item #1003 455 105
Model #PPSPAGLC30DM
Use and Care Guide
Vanity Combo
TOOLS REQUIRED
Hammer Safety goggles Phillips screwdriver Power drill
Measuring tape Wall hardware Caulk/sealant
Installation
1 PREPARING FOR INSTALLATION
NOTE: Before installation, make sure
all parts are present. Compare parts with
the Hardware Included list. If any part is
missing or damaged, do not attempt to
install the product.
□ Determine the desired mounting location,
and mark the wall where the unit will be
installed.
NOTE: For secure installation, the
unit must be mounted to at least one
wall stud.
Keyhole saw
HARDWARE INCLUDED
AA - Handle x 2 CC - Hanging bracket x 2
Level
BB - Handle Screw x 4 DD - Screw x 4
2 CUTTING THE OPENING FOR PLUMBING FIXTURES
NOTE: This step applies to vanity cabinets with full back panels only.
□ Locate and mark plumbing on the back panel.
□ Drill a pilot hole through the back panel.
□ Use a keyhole saw to cut an opening for the plumbing fixtures.
3 POSITIONING THE CABINET
□ Move the cabinet into place, and use wood
shims to level the cabinet against the wall.
4 INSTALLING THE CABINET
□ For wall stud installation, insert #12 x 3 in.
screws with washers into the stud locations
(not included).
□ For drywall installation, drill holes at the
appropriate locations and insert toggle bolts
with washers (not included).
□ For concrete wall installation, drill 1/4 in.
holes at the appropriate locations and insert
#12 wall anchors, followed by #12 x 3 in.
screws (not included).
5 INSTALLING THE VANITY TOP
IMPORTANT: Do not use plumber’s putty.
NOTE: The faucet, drain, and supply lines are not included. Install these
parts to the vanity top according to the manufacturer’s instructions.
□ Apply silicone caulk/sealant (not included) to all four corners of the cabinet.
□ Place the vanity top onto the cabinet.
□ Position the top so that it has an equal amount of overhang on each side
and use a level to ensure the vanity top surface is level.
□ Apply silicone onto the seam between the edge of the vanity top and the
wall, smooth the bead, and allow to cure before use.
NOTE: Matching side and back splashes available, sold separately.
To purchase, visit your local Home Depot store or go to homedepot.com.
HOMEDEPOT.COM
Please contact 1-888-774-8062 for further assistance.
Installation (continued)
6 INSTALLING THE HARDWARE
□ Attach the handles (AA) to the cabinet with the provided screws (BB).
7 REMOVING THE DRAWER
□ Press release levers in opposite directions while pulling drawer out of the vanity.
8 RE-INSTALLING THE DRAWER
BB
AA
Press
downward
Press
upward
NOTE: Drawer should install smoothly; however, there may be minor resistance
when the drawer is approximately half to two-thirds installed. This is normal.
□ Move the ball bearing cages to the front and push the rear of the glides
toward the center of the vanity.
□ Insert the drawer box.
□ Ensure the drawer box glide members slide through the plastic guide at
the front of the vanity member on each side.
9 INSTALLING THE HANGING BRACKETS
NOTE: Before installing, make sure all parts are
present. Compare parts with the Hardware Included
list. If any part is missing or damaged, do not
attempt to install the product.
□ Attach the hanging brackets (CC) to the back
of the mirror using the included screws (DD).
DD
CC
10 INSTALLING THE HANGING WIRE
NOTE: This step is optional, and the
hanging hardware is not included.
□ If you choose to
use hanging wire
(not included)
attach it to brackets
as shown below.
11 INSTALLING THE MIRROR
□ For wall stud installation, insert #12 x 3 in. screws with washers into the stud
locations (not included).
□ For drywall installation, drill holes at the appropriate locations and insert
toggle bolts with washers (not included).
□ For concrete wall installation, drill 1/4 in. holes at the appropriate locations
and insert #12 wall anchors, followed by #12 x 3 in. screws (not included).
HOMEDEPOT.COM
Please contact 1-888-774-8062 for further assistance.
Loading...