Borescope
GBS-101
User Manual
Notice on patent, trademark, copyright, copyright and intellectual property rights in user manual
Patents, trademarks, copyrights, copyrights, and intellectual property rights of this user manual are owned by GIT.
No part or all of this manual may be reproduced or used in any form without written permission of GIT.
Purchase of this user manual does not imply a transfer of patent, trademark, copyright, copyright, or intellectual property rights.
GBS-101 (Wireless Car Endoscope) is a registered trademark of GIT.
ⓒ All rights reserved, GIT Co., Ltd.
Limitation of Liability
All contents and images used in this user's manual may be modified, attached or deleted without notice due to improvement
or improvement of product function and specification.
For products not manufactured by G.I.T CO., LTD, such as tablet PCs, comply with the manufacturer's A / S standards.
In addition to the programs recommended by G.I.T CO., LTD, customers are not entitled to free warranty for problems
caused by installing or modifying other programs or changing or deleting diagnostic programs.
This product is a device to check the internal condition of the car through the car endoscope. The diagnosis and repair method
should be finally decided by the user. The manufacturer and the seller are not responsible for the result of the defect diagnosis
and repair method.
Contents
Warning and cautions for safety before Use
A
Basic components
B
Ready to use the product
C
C1. Name of each part
C2. Product assembly
C3. Product charge
Device connection
D
D1. USB connection
D2. Wi-Fi connection
Screen layout
E
E1. Main screen
E2. Taken image
E3. Video recording
Function
F
F1. Note Mode
F2. Image editing
F3. Screen rotation
F4. LED brightness adjustment
4
5
6
7
8
9
11
12
13
13
14
15
15
15
Setting
G
G1. Resolution setting
G2. Sleep mode setting
H
Internal Battery Replacement
I
Product specification
J
Certification
J1. Certification
J2. Product warranty
16
16
17
18
18
19
3
A. Warning and cautions for safety before use
[WARNING] The user is responsible for any damages incurred due to
!
When connecting with a DC charger, do not use any charger other than the specified DC charger.
Make sure all cables are connected properly during operation. Do not disconnect the data cable or power cable
without completing the operation.
Please note that if the product is arbitrarily disassembled, modified or altered, normal service cannot be provided.
Use only genuine cables manufactured by GIT for cables, chargers, and all other parts and accessories used together.
Use the specified device and program.
Handle the product within the operating temperature and humidity.
Using this product in an excessively blocked space may cause radio interference. Wireless communication may be
interrupted temporarily or continuously, depending on the wireless communication environment.
This product is a short-range wireless device that can be limited in long-range connection.
insufficient knowledge of the contents of this endoscope user manual or
the operation used differently from the contents of this manual.
[CAUTION] Inadequate handling can result in personal injury or property damage, with
more serious consequences under certain conditions. Follow all safety instructions and
instructions.
Do not store in locations where flammable materials and strong static electricity can be generated.
Chemicals or acids can corrode products and accessories.
Do not impact the product.
Cool the engine sufficiently(Less than 50 degrees) and use it at low temperatures.
Do not touch the camera while the LED is on. There is a risk of burns.
Be aware of the damage caused by high temperatures and moving parts when using the engine compartment.
Do not let the main unit containing the rechargeable battery and cable get wet.
Do not disassemble the rechargeable battery.
Be careful not to touch your eyes or skin with a leak caused by improper use of rechargeable batteries.
Only use the specified rechargeable batteries with the products.
Keep the camera and data cable out of contact with water.
Be careful to store all components when not in use.
Do not pull on the cable when moving or using the product.
GIT is not responsible for any damages caused by PCs that are not recommended to use with.
Do not expose the product to an X-ray or microwave; it may cause serious damage to the product.
Do not keep it in the following location:
- In places where the temperature and humidity are too high or too low (check the product specifications).
- Places exposed to direct sunlight for a long time
- Inside the vehicle in Summer season
- Place with moisture and watery
4
B. Basic components
품 목 외 형 설 명
Main body
0˚
Camera
90˚ Camera
Flexible tube
0˚ Magnetic holder
90˚ Magnetic holder
The main body connects the camera and the
flexible tube Perform the endoscope function.
0 degree camera used for frontal shooting.
90 degree camera used for side shooting.
The probe connects to the body and the camera.
It can be mounted in the camera lens groove to
lift a small bolt or screw.
It can be mounted in the camera lens groove to
lift a small bolt or screw.
Micro USB cable
DC cable
Charger & plug
Manual
USB C-Type gender
Cleaning fabric
GBS-101
MANUAL
The cable used to connect wireless
endoscopes and tablets by wire.
Cable length: 150cm
This cable is used to supply power to the
VCI using a DC power adapter.
Used to charge by connecting the DC cable.
Plug: Provides one of three types.
This manual contains information on how to
use the product safely and normally, and
related specifications. (Specifications may
change depending on the situation.)
C type gender that can replace 5Pin cable.
Cleaning fabric for wiping camera lenses.
Bag
A bag for carrying and storing the wireless
endoscope.
5
C1. Name of each part
Wi-Fi mode power button
UP button: LED Brightness button (0~3step)
DOWN button: Preview Rotation Button(90degrees)
Capture button
Long press: Start / stop movie recording
Short press: Take a picture
Indicator LED
Connection method
Wi-Fi
Charge
USB
Status
At boot
When booting up /
Waiting for Wi-Fi connection
Connecting to Wi-Fi
Upon Wi-Fi connection
Low battery
At power off
Charging
Fully charged
When the program is connected
LED
Blinking blue
Blue/green flashing
Blinking green
Green light
Red/blue flashing
Blinking red
Red light
Red off
Blue light
+DC 5V Input terminal
USB Input terminal
6
C2. Product assembly
1
Insert the flexible tube into the body and screw it to fix it.
Make sure the groove or arrow is pointing up when inserting the tube.
Check the direction of
the arrow and groove
2
Insert the camera on the other side of the flexible tube and turn it to fix it.
Make sure the red circle is aligned when inserting the camera.
Camera
7
C3. Product charge
This product requires charging because it consumes its own battery when wirelessly used. USB connection is available without
charging.
1
Connect the DC cable to the 5V 2A charger.
DC cable
Remove the waterproof cover on the back of the main unit and connect the DC cable
2
to the DC input terminal.
(Charging time: about 3 hours)
※
Power supply method
Wi-Fi mode: Battery and charger
USB mode: Tablet
8
D1. USB connection
1
If the Wi-Fi power is on, press the power button to turn it off.
Wi-Fi power must be off to enter USB mode.
Micro USB cable
Wi-Fi mode power LED
Wi-Fi mode power button
2
Connect the micro USB cable.
3
Connect the other end of the cable to your tablet.
9
4
Run the GDSM / KDS app on your tablet.
5
Automatically try to connect to USB.
7
Start shooting with the button.
LED brightness
adjustment
6
When USB is connected, it moves to the
shooting screen.
KA981121312449231
12/08/2019
상단에 USB 접속 중임을 표시하고 있습니다.
8
If the USB connection fails, reconnect
the USB cable.
10
Preview screen
rotation
Capture button
Long press: Start / stop video recording
Short press: Take a picture
USB connection status
The LED lights up blue( ).
D2. Wi-Fi connection
1
Press the button for 3 seconds.
Wi-Fi mode power button
3
Look for the four-digit code on the label
on the bottom of the device.
2
Stand by until the boot is complete.
When booting is complete, the LED blinks blue
and green( ).
Wi-Fi mode power LED
4
Run the app, enter the 4 digit code and
press the device search button.
SSID: Borescope_XXXX
CODE: XXXX
5
Once the device is detected, press the
Connect button to connect.
If you check Auto setup after remembering your password,
the code is saved to simplify the connection process.
6
hen the Wi-Fi is connected, it moves to
the shooting screen.
KA981121312449231
12/08/2019
Wi-Fi connection
The green( ) LED lights up.
It shows that you are connected to Wi-Fi at the top.
(Displays battery information and SSID of the device
together.)
11
E1. Main screen
Battery level
LED brightness
Connection Settings
Microphone volume
Note mode
Editing mode
LED brightness adjustment
Camera preview
VIN
KA981121312449231
Date
12/08/2019
Key operation during shooting
Photo shooting
Video recording
Preview screen
rotation
Preview screen rotation
12
Long press: Start / stop video recording
Short press: Take a picture
E2. Taken image
Record the vehicle's VIN and date when taking photos and videos.
File storage location: Internal storage/mvci/GDSCAM/Record
※
E3. Video recording screen
Recording screen
KA981121312449231
12/08/2019
Date
VIN
Note mode
Editing mode
Photo shoot
Recording Time
Stop recording
VIN
Date
Pause
13
F1. Note Mode
1
Select button on the shooting screen.
KA981121312449231
12/08/2019
3
When mode is activated as below, you
can display the text on the photo
2
Once the Mode at the bottom is activated,
you can draw on the photo.
Text box
Pen mode
Pen thickness
4
Long press on the photo to enter
text in the textbox.
KA981121312449231
Delete all
Redo
Undo
12/08/2019
Pen color
KA981121312449231
12/08/2019
Text color
5
Press button again to finish writing.
If you rotate the preview screen before saving,
the text box contents disappear.
You can delete and edit by selecting the text box
above the photo.
14
F2. Image editing
1
To edit the photo, select button
on the screen.
3 Press the ‘SAVE’ button to save.4
Edit the photo using the pen or text box.
2
The recorded picture is displayed.
Select the picture you want to edit.
When saving, you can save it with a different name.
F3. Screen rotation
1
Select button to rotate the preview
screen by 90 degrees.
KA981121312449231
12/08/2019
It does not rotate during shooting.
F4. LED
1
Press the LED brightness button on
brightness adjustment
the device to adjust the brightness.
Brightness is 0 to 3 levels and is displayed on the screen.
0 is the LED is off.
15
G1. Resolution setting
1
You can adjust the resolution by selecting
the Settings button on the shooting screen.
KA981121312449231
12/08/2019
G2. Sleep mode setting
1
You can turn sleep mode off or on by
tapping the tab in the Settings pop-up.
2
This product supports three resolutions.
(640X480,800X600,1280X960)
2
If there is no operation for a certain
period of time, power save mode and
sleep mode are activated.
16
Power save mode:
The Sleep Mode activates after 10 minutes of inactivity.
You can use it immediately by touching the screen.
Sleep mode (optional):
The program will exit after 60 minutes of inactivity.
Re-use is required for reuse.
H. Internal battery replacement
1
Turn the rear screw counterclockwise with a screwdriver.
2
Remove the screw and detach the battery cover on the handle part downward.
3
Remove the rechargeable battery and replace it with a new one.
Close the cover in the reverse order and secure it with the screw.
17
I. Product specification
Item The details
Camera
Resolution
Lens
Focal length
LED
Outer diameter
Product length
Magnetic holder
3-part assembly
Brightness adjustment
Camera connection
method
2EA [Front(0°), Side(90°)]
C-MOS
[640X480,800X600,1280X960]
Angle of view: 67°/ Iris: F2.8
None AF/Anti-fog coating
9.5~300 mm
White Chip LED 6EA
Camera Head Ø8.2
Camera Joint Wire Ø8.0
1M
2 EA [Front(0°), Side(90°)]
Camera / Flexible Tube / Body
Implemented in Hardware (Step 3)
Wi-Fi Direct (Wireless LAN IEEE 802.11 b/g/n)
USB (UVC 1.1 )
Battery capacity
Use temperature
Dustproof / Waterproof
DC 3.7 V 2,600mAh
-20
℃ ~ +70℃
IP64
18
J1. Certification
※ This wireless device is likely to be radio wave involved during operation.
This device complies with part 15 of FCC Rules. Operation is subject to the following
two condition: (1)This Device may not cause harmful, and (2)This device must accept
any interface received, including interface that may cause undesired operation.
Any changes or modifications (including the antenna) made to this device that are
not expressly approved by the manufacturer may void the user’s authority to operate
the equipment.
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
*FCC ID :TMGG0DKDNN041
J2. Product warranty
[Purchase information]
Product name
GBS-101
S/No.
Purchase date
(1 year warranty)
[Customer information]
Company Name
Name
Phone number
Address
※
Free service
After purchase, you are entitled to free service only if the product malfunctions within the warranty period (see below).
If the date of purchase cannot be confirmed, the warranty period will be calculated from the headquarters
release date +90 (product shelf life).
Warranty period for each item
Item
Main body
Accessory
Expendables
Type of damage
Poor during normal use
When you purchase
the first product SET
1 year
1 year
None
※ Batteries are consumable parts, but for new devices battery warranty is 6 months.
When purchasing
individual units
1 year
6 months
6 months
Reassurance after repair
3 months
N/A
N/A
Compensation criteria by type
When you need a major repair within 10 days of purchase
When you need important repair within one month after purchase
Repairable
Not repairable
Damage caused by not having repair parts
within the parts retention period
Damage incurred during transportation and
product installation during product purchase
GBS-101 item classification
Item
Main body
Accessories
Expendables
Type
In case of malfunction during normal use
When the same part is defective 3 times
In case of malfunction due to intentional
or negligence by the consumer
In case of malfunction during normal use
In case of malfunction due to intentional
or negligence by the consumer
subject
GBS-101 Main Module (Main body)
0/90 degree camera, Flexible tube, 0/90 degree magnetic holder,
Micro USB cable, DC cable, Charger and plug, C type gender
Battery, User manual, Clinic fabric, Carrying bag
Within warranty
period
Product Exchange
Warranty
Warranty
Product Exchange
Paid Repair
Product Exchange
Our Regulation
Processing
Product Exchange
Product Exchange
After warranty
N/A
N/A
Paid Repair
Paid Repair
Paid Repair
Our Regulation
Processing
Our Regulation
Processing
Our Regulation
Processing
N/A
19
www.gitauto.com
20
Loading...