GIRA
Info
Electronic timer
Installation Instructions
Electronic timer 3/07 Page 1 of 14
Contents
1. Warning
2. Function
3. Installation Instructions
4. Programming
4.1. Setting Current Data
4.2. Astro Function
4.3. Random Function
4.4. Factory Setting and Reset
4.5. Programming Individual Switching Time Events
4.6. Deleting Switching Time Events
4.7. Programming an Astro Time Shift
5. Mode Selection
5.1. Selecting the Program Memory
5.2. Selecting the Time Switch Function
5.3. Manual Operation
5.4. Winter/Summer Time Selection
6. What To Do in Case of Mains Failure?
7. Specifications
8. What happens if...
9. Acceptance of guarantee
2. Function
This attachment is installed into a 60 mm flush box
(recommendation: deep box) in conjunction with the
insert.
The device facilitates the programmed, time-controlled switching of various lighting fittings (please refer to
Specifications) up to a maximum of 1000 W.
Electronic timer
Attachment
Order no.: 0385 xx
1. Warning
Caution: The installation and assembly of electrical
equipment may only be performed by a skilled electrician.
This electronic timer has been designed for switching lamps. For the lamp load ratings, please refer to
the Specifications of the flush-mounted insert. Do
not switch any other loads.
GIRA
Info
Electronic timer
Installation Instructions
Electronic timer 3/07 Page 2 of 14
Product features:
• Simple operation through a four-key field.
• Two independent program memories for a total of
up to 18 switching time events (e. g. nine ON and
nine OFF times).
• Time switch function.
• Random function.
• Astro function.
• Summer/winter time change-over.
• Individual astro function by astro time shift.
• Driving via extensions (insert).
• Reset facilitates resetting to factory adjustment.
• Up to 24-hour power reserve (maintenance-free,
without batteries).
3. Installation Instructions
The attachment can only be placed into service in
conjunction with the Electronic timer insert.
Electronic timer insert should be installed in a 60
mm flush box (recommendation: deep box).
The connecting terminals of the insert must be down.
Plug attachment onto the insert together with frame
.
Electrical contacting is established through plug .
l
4. Programming
Note:
If no operation is made for longer than 2 minutes during programming, the electronic timer will automaticliy
return to displaying the current data.
Programming can be cancelled any time by pressing
the SET key for about 3 seconds.
4.1. Setting Current Data
Prior to entering your data please make a reset to
bring back the device to factory default setting:
Depress the MODE and SET keys at the same time
until all display segments light up for a short time (approx. 7 sec.). This completes the reset.
To enable the Electronic Time Switch to start its operation, please enter the current data:
Hold the SET key depressed until the display reads
prog.
Use key ON or OFF to select the following settings
(please refer to the diagramm):
Time, Date : Set current data
A: Programming memory A
B: Programming memory B
Astro : Shift astro times
Mode
Set
ON
OFF
GIRA
Info
Electronic timer
Installation Instructions
Electronic timer 3/07 Page 3 of 14
Accept the Time, Date symbol by shortly depressing
the SET key.
The Electronic Time Switch is now in the current data
setting mode.
Setting summer/winter time:
Use key ON or OFF to set summer time (S) or winter
time (W).
Accept by shortly depressing the SET key.
Setting the current month:
Use key ON or OFF to set the month (01..12).
Accept by shortly depressing the SET key.
Setting the current date:
Use key ON or OFF to set the day (01..31) .
Accept by shortly depressing the SET key.
Setting the current day
Use key ON or OFF to set the day (MO..SU).
Accept by shortly depressing the SET key.
Setting the current hour
Use key ON or OFF to set the hours (00..23).
Accept by shortly depressing the SET key.
Setting the current minute
Use key ON or OFF to set the minutes (00..59).
Accept by shortly depressing the SET key.
The electronic timer has taken over the current data
and changed over to its normal operating mode.
4.2. Astro Function
If the light is to be turned on at sunset or to be turned
off at sunrise, switching time events once programmed must be continuously adapted to the
changing astronomical calendar in automatic mode
(please refer to the illustration).
For this purpose, the Electronic Time Switch calculates the time of sunrise and sunset for each day of
the year (for the approximate location of Würzburg).
GIRA
Info
Electronic timer
Installation Instructions
Electronic timer 3/07 Page 4 of 14
By adding the astro program, programmed OFF
switching time events are executed at the time of sunrise already. Programmed ON switching time events
are only executed at the time of sunset. OFF switching time events that are in the darkness in the morn-
ing and ON events in the evening darkness are not
shifted.
To adapt the pre-programmed astro times to the local
conditions, the astro times can be shifted by a maximum of +/- 1 hour and 59 minutes.
Programming examples:
If light is to be turned on daily at sunset and to be
turned off at sunrise, the following programming and
activated astro function can be used to effect this:
Event 1: MO-SU at 16:00 hrs. ON.
Event 2: MO-SU at 22:00 hrs. OFF.
To turn off at 6:30 hrs. in the morning, at the latest and
to turn it on 19:10 hrs. in the evening at the earliest,
use the following program with activated astro function (please refer to the illustration):
Event 1: MO-SU at 6:30 hrs. OFF.
Event 2: MO-SU 19:10 hrs. ON.
4.3. Random Function
If the random function is activated for a certain switching time event, this switching time is varied by +/- 15
minutes. The random time shift is used for all switching time events and changed daily.
If the astro function is additionally activated for this
switching time event, this switching time event will be
adapted to the respective time of sunrise or sunset
and varied by a random time of +/- 15 minutes.
4.4. Factory Setting and Reset
Manual operation has, in all cases, priority over automatic mode.
In the two program memories A and B, independent
programs can be stored (e.g. for everyday use, weekend, vacations etc.). A maximum of 18 different
switching time events can be used in the two program
memories altogether (e.g. nine time events per memory).
Program memories are factory-preset but can be
overwritten by your own programming (in such case,
erase switching times not required).
15 16
3
4
5
6
7
8
9
5 1015202530354045 50
4
5
6
7
8
9
10
Jan.
Jul. Dez.Apr. Okt.
WZ SZ
KW
Dunkelheit Darkness
Tageslicht
16
17
18
19
20
21
17
18
19
20
21
22
5 1015202530354045 50
Jan.
Jul. Dez.Apr. Okt.
WZ SZ
KW
Daylight
Dunkelheit Darkness
Kalenderwoche Calendarweek
4
5
6
7
8
9
10
5 101520253035404550
15
16
17
18
20
21
19
U
h
r
z
e
i
t
T
i
m
e
Ausgeführte AUS-Zeit
Practiced OFF-time
Programmierte AUS-Zeit 6.30 Uh
r
Programmed OFF-time 6.30 h
Programmierte EIN-Zeit 19.10 Uhr
Programmed ON-time 19.10 h
Ausgeführte EIN-Zeit
Practiced ON-time
Tageslicht
Daylight
Dunkelheit
Darkness
Darkness
Dunkelheit
GIRA
Info
Electronic timer
Installation Instructions
Electronic timer 3/07 Page 5 of 14
Memory A:
Event 1: OFF 07:00 hrs, MO-FR, astro function active
Event 2: OFF 09:00 hrs, SA-SU, astro function active
Event 3: ON 20:00 hrs, MO-FR, astro function active
Event 4: ON 21:00 hrs, SA-SU, SA-SO, astro function
active
Memory B:
Event 1:OFF 07:00 hrs, MO-FR.
Event 2:OFF 09:00 hrs, SA-SU
Event 3:ON 20:00 hrs, MO-FR
Event 4:ON 21:00 hrs, SA-SU
Timer function C:
The timer has been factory-preset to 15 minutes. For
individual settings, please refer to Chapter 7.
By RESETTING the Electronic Time Switch, programming can be reset to factory defaults. In this case
the current data and your own programming will be
deleted.
To RESET:
Depress the MODE and SET keys at the same time
until all display segments light up for a short time (approx. 7 seconds). This completes the reset.
4.5. Programming Individual Switching Time
Events
Note: If switching time events overlap (identical time
and day for ON and OFF), the OFF event will be executed.
Example:MO ON 8:15 hrs. not executed.
MO OFF 8:15 hrs. executed.
Depress the SET key until the display reads prog.
Selecting the program memory
Use key ON or OFF to select program memory A or
B. Select that programm memory where your new
switching time events are to be stored.
Accept your selection by shortly depressing the SET
key.
The electronic timer is now in the mode for programming new switching time events.
Selecting a memory location
Key ON or OFF indicates the switching time events
which a re already stored in the program memory.
With the ON key, you can scroll towards earlier
events, while the OFF key brings you to later events.
New switching time events are automatically sorted
into this list.
Note: A maximum of 18 different switching time
events can be stored. These events can be distributed over two program memories (A, B). If all these 18
switching time events have been programmed (e. g.
nine ON and nine OFF times), the display reads
‘FULL’ at the end of the table of events.
Select your desired memory location where the new
switching time event is to be stored. Any switching
time event existing at this memory location will be
overwritten.
Mode
Set
ca. 7 Sek.
A
B
C
WS
Datum
Uhrzeit
Prog Zufall
Astro
Mo
Di
Mi
Do
Fr
Sa
So
ON
OFF
Mode
Set
ON
OFF
Loading...