Gira 5352 10 operation manual
Wireless remote control, 2-gang, Wireless remote control, 4-gang
Wireless remote control, 2-gang
Order No. : 5352 10
Wireless remote control, 4-gang
Order No. : 5354 10
Operating instructions
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled
persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Keep button cells out of reach of children! If button cells are swallowed, get medical help
immediately.
Risk of explosion! Do not throw batteries into fire.
Risk of explosion! Do not recharge batteries.
The radio communication takes place via a non-exclusively available transmission path,
and is therefore not suitable for safety-related applications, such as emergency stop and
emergency call.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
Figure 1: Radio hand transmitter 2-gang and 4-gang
(1) Status LED
(2) Buttons
3 Function
Intended use
- Hand transmitter for radio transmission of switching, dimming, blind movement and scene
commands
- Operation with radio actuators from the eNet system
Product characteristics
- Two adjacent buttons each belong to one channel
32582422 25.04.2017
10864952
1/7
Wireless remote control, 2-gang, Wireless remote control, 4-gang
- Status indication with LED
- Switch-on brightness of dimmer actuators can be saved.
- Battery-powered device
- Scenes, radio hand transmitter, 2x: All Off, three individual scenes.
- Scenes, radio hand transmitter, 4x: All Off, seven individual scenes.
- Signalling of transmission errors can be switched off
Can be set with eNet server:
- Scene All On
- Operation locks
Supplementary functions with eNet Server
- Fully encrypted radio transmission (AES-CCM) from eNet Server software version 2.0
- Update of the device software
- Reading of error memory
4 Operation
i When operating with the eNet Server, operation and signalling could vary from what is
described here.
One channel of a radio hand transmitter consists of two buttons. These can be used in two
different ways.
- As channel buttons for switching, dimming, Venetian blind operation
- As scene buttons to recall set scenes
Function of status LED in operation
As soon as a button is pressed or released, the status LED (1) first signals radio transmission
- LED turns red for 3 seconds
and then the actuator status/group status
- LED turns green for 3 seconds:
At least one actuator is switched on, or one Venetian blind is not in the top end position
- LED remains off:
All the actuators are switched off or the blinds are all in the upper end position
or - if there is no status message from an actuator - a transmission error.
- The LED rapidly flashes red for 5 seconds:
The status message of at least one actuator is missing
Operating light
o Switching: Press button for less than 0.4 seconds.
o Dimming: Press the button for longer than 0.4 seconds. The dimming process ends when
the button is released.
o Switching on dimmer actuators at minimum brightness: Press the right button for longer
than 0.4 seconds.
o Switching on dimmer actuators at minimum brightness and dimming to maximum
brightness: Press the left button for longer than 0.4 seconds.
Operating blind
o Moving the Venetian blind: Press the button for longer than 1 second.
o Stopping or adjusting the Venetian blind: Press the button for less than 1 second.
Operating push-button actuator
o Press the button. The load is switched on for the duration of the button-press.
i The maximum actuation length is 60 seconds.
Recalling scenes
o Press the scene button briefly.
Actuators switching to the saved scene.
32582422 10864952 25.04.2017
2/7
Wireless remote control, 2-gang, Wireless remote control, 4-gang
Changing scene
o Press the scene button briefly.
Actuators switching to the saved scene.
o Setting a new scene.
o Press scene button for longer than 4 seconds.
Actuators first switching to the old scene and save the new scene after 4 seconds.
Save switch-on brightness
With dimmer actuators a brightness value can be saved to which the dimmer actuator switches
after a short button press.
The buttons of a channel are set as channel buttons.
o Set required switch-on brightness.
o Press both buttons of a channel simultaneously for longer than 4 seconds.
The light is briefly switched off and switched on again to the switch-on brightness. SwitchÂon brightness is saved.
Polling sum status
The buttons of a channel are set as channel buttons.
o Press both buttons of a channel simultaneously for 1 to 4 seconds.
Signalling of radio transmission and group status (see function of the status LED in
operation)
5 Information for electrically skilled persons
5.1 Commissioning
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
During commissioning, cover the parts carrying voltage on radio transmitters
and actuators and in their surrounding area.
Insert battery
WARNING!
Risk of chemical burns.
Batteries can burst and leak.
Replace batteries only with an identical or equivalent type.
o Open battery compartment on the rear side of the hand-held transmitter.
i Keep contacts of batteries and device free of grease.
o Apply battery to the positive contact of the battery holder. Observe polarity: the positive
pole of the battery must be at the top.
o Press gently on battery to snap it in.
o Close battery compartment.
Hand-held transmitter is ready for operation.
32582422 10864952 25.04.2017
3/7
Loading...