GinSan Doghouse GS-400, Doghouse GS-400II, Doghouse GS-401, Doghouse GS-60, Doghouse GS-610 Owner's Manual

ClubPet

ALL INCLUSIVE SPA EXPERIENCE FOR THE FOUR-LEGGED

© 2010 GinSan Industries

Pet Wash System

Owner’s Manual

© 2018 - GinSan Industries - Grand Rapids, MI USA

www.GinSan.com

800.446.7267

0052450 Rv 082018

PET WASH

SYSTEM

Table of Contents

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Dimensions - Corner Spa (Standard) . . . . . . . . . . . . . . . . . . . . . . . 3

Dimensions - Corner Spa (In-Bay) . . . . . . . . . . . . . . . . . . . . . . . . . 4

Wiring Diagram w/GS-400 (Prior to 1/2018). . . . . . . . . . . . . . . . . . 5

Wiring Diagram w/GS-401 (Prior to 1/2018). . . . . . . . . . . . . . . . . . 6

Wiring Diagram w/GS-400 (After 1/2018) . . . . . . . . . . . . . . . . . . . . 7

Wiring Diagram w/GS-401 (After 1/2018) . . . . . . . . . . . . . . . . . . . . 8

Wiring Diagram w/GS-60 with GS-400II, Coin Accptor & CryptoPay NG........ 9

Wiring Diagram w/GS-60 with LED6, Coin Acceptor & CryptoPay NG .......... 10

Wiring Diagram w/GS-60 with LED7 & CryptoPay NG ................... 11

Wiring Diagram w/GS-610 with LED6 & CryptoPay NG using aux. coin input ...... 12

Wiring Diagram w/GS-160 with LED7, Coin, Bill Accptor & CryptoPay NG ........ 13

Wiring Diagram Ultimate Rotary 10 Position with LED6 & CryptoPay NG .... 14

Wiring Diagram Ultimate Rotary 8 Position with LED7 & CryptoPay NG ..... 15

Plumbing Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Installation Instructions - Corner Spa. . . . . . . . . . . . . . . . . . . . 17-22

Installation Instructions - High Flow Rinse. . . . . . . . . . . . . . . . 23-24

©2018 - GinSan Industries

PET WASH

SYSTEM

GinSan Industries provides a limited one year warranty on components and piece of equipment produced by the
Company to be free from defects in material and workmanship. Electrical assemblies see Appendix A, have a limited
two year warranty on the controller to be free from defects in material and workmanship. This limited warranty
does not cover equipment that has been damaged due to misuse, misapplication, modification, altered, neglected,
attempted theft, vandalism, connection to improper voltage supply, modification, or such parts that are commonly
recognized to be subject to wear in normal usage. Normal use products are, but not limited to, those listed on
Appendix B; which are warranted for 90 days. Every component and piece of equipment is packaged to assist in safe
handling of the product.

Claims must be submitted in writing within the appropriate coverage period as covered by this warranty, from date of
shipment, to the Company’s warranty/repair department. If the return is approved an RMA and labeling instructions
will be issued and the product can be returned. Returned product without the appropriate RMA and label will be
issued to scrap and all warranties/replacements will be considered null and void. If the product receiving the RMA is
not returned within 20 days from date of issuing the RMA then any credit toward the product will be reduced by 25%. If
the product is not returned within 30 days of issuing the RMA then any credit will be reduced by 50%. A testing fee of
$20.00 will be applied, if the product passes all tests related to the written claim, then the fee will be applied and paid
prior to return of the product. If the product fails the test then the fee will not be applied. If a product is determined to
be non-repairable, a $20.00 testing fee will be applied. The Company may charge a 20% restocking fee for returned
product and/or an order, which is canceled and/or material has already been ordered and/or received to fill such
order. The average lead time for in house repairs is 3 weeks. If you require expedited service a 20% expedite fee will
be assessed to the total cost of repairs with a $20 minimum and $500 maximum. The warranty on repaired items is 90
days against failures in parts and/or workmanship.

Limited Warranty

The Company’s warranty/repair department will inspect all components, submitted under warranty. Warranty
replacement will be based solely on the analysis and confirmation that the product defect was caused by material and/
or workmanship. The company reserves the right to change the design of the product without assuming any obligation
to modify any product previously manufactured or to replace warranted product other than with redesigned product.

In some cases it is easier for the customer to send a Company purchased product direct to the manufacturer for
replacement. In those cases the customer will be notified that their product falls under that process and should work
with that manufacturer directly. Appendix C shows the purchased parts that falls under this case.

This warranty covers the product replacement only; charges for damages, freight and/or labor will not be accepted.
There are no warranties expressed or implied which extend beyond this Limited Warranty. The loss of use of the
product, loss of time, inconvenience, commercial loss, incidental or consequential damages is not covered. The
Company shall not be liable for incidental, special, or consequential damages including without limitation damages
resulting from personal, bodily injury or death or damages to or loss of use of property.

APPENDIX A
2-Year Warranty Controllers:
Sensortron, Multitron, Touchtron, 24 VAC Timer, Liberator

APPENDIX B
90-Day Warranty Components:
Pressure Hoses, Swivels, Nozzles, Safety Shut-off Guns, Seals, O-Rings, Shop Vac, Electromechanical Devices,
Vacuum Motor Brushes Valves, Regulators

APPENDIX C
Purchased Products that are Handled Direct with the Manufacturer:
Shop Vac, IDX Products, Bill Acceptors, Compressors, Pump Motors, Dixmor Timers, CAT Pumps, Flojet Pumps

©2018 - GinSan Industries

Page 1

PET WASH

SYSTEM

19½"

35"

Dimensions

33½"

86"

48"

41"

34"

24"

Dimensions (With Optional Cabinet)

92"

54"

52"

35"

34"

24"

©2018 - GinSan Industries

Page 2

PET WASH

SYSTEM

Dimensions - Corner Spa (Standard)

33½"

35½"

19½"

52½"

©2018 - GinSan Industries

Page 3

PET WASH

SYSTEM

Dimensions - Corner Spa (In-Bay)

33½"

35½"

19½"

©2018 - GinSan Industries

Page 4

PET WASH

WHITE

. 8th and 9th functions not available

3/8" NC Inlet

Wiring Diagram w/GS-400

SYSTEM

Transformer

120VAC to 24VAC

PN 18801

3/8" NC Inlet

Solenoid

PN 19069

Solenoid

19069

PN

BLACK

Fuse Holder

1 amp fuse PN 20316

RED

PURPLE

6 Function Solenoid Assembly

PN 18580K x 2

1 2 3 4 5 6

PN 20317

(Prior to 1/2018)

Power Cord

PN 68263

BLACK

TAN

PURPLE

Function on 20 Position

Terminal Strip

Function

1 24V Hot Red
2 24V Common Purple
3 Main Water Solenoid Black
4 4th Chemical Orange/Blk
5 Rinse Grey
6 2nd Chemical Pink
7 3rd Chemical White
8 5th Chemical Blue
9 Not Used ­10 Timed Hot Yellow
11 1st Chemical Brown
12 6th Chemical Black/White
13 Not Used ­14 Low Dry Red
15 High Dry White
16 24V Common Purple or Blk
17 24V Common Purple or Blk
18 24V Common Purple or Blk
19 24V Common Purple or Blk
20 24V Common Purple or Blk

Color

Pet Dryer

(optional)

RED

PURPLE

ORANGE/BLK

GREY

PINK

WHITE

1.

2.

3.

4.

5.

6.

7.

BROWN

BLACK/WHITE

RED

WHITE
PURPLE
PURPLE

BLACK

BLACK- 24V Common
RED- Low Dry
WHITE- High Dry

NOTE: For use with 10 position rotary switch. 9th function not
available with touchtron door
with 8 positon rotary door.

9.

10.

11.

12.

13.

14.

17.

15.

16.

20 position

terminal strip

PN 18721

8.

In meterbox hull

See DogTech-005 for

8 + 10 position rotary

See DogTech-006 for

Touchtron doors

©2018 - GinSan Industries

PRIOR TO JANUARY 1, 2018

Page 5

PET WASH

WHITE

. 8th and 9th functions not available

3/8" NC Inlet

Wiring Diagram w/GS-401

SYSTEM

Transformer

120VAC to 24VAC

PN 18801

3/8" NC Inlet

Solenoid

PN 18481P

Solenoid

PN 18481P

BLACK

Fuse Holder

1 amp fuse PN 20316

RED

PURPLE

6 Function Solenoid Assembly

PN 18581

1 2 3 4 5 6

PN 20317

Power Cord

PN 68263

RED/GREEN

PURPLE
YELLOW

RED

(Prior to 1/2018)

GS-401

GS -401

0000

5
4
3
2
1
A

INCREASE

(RESET)

COIN COUNT

AUX COUNT
RESET/CANCEL
TIME PER COIN

COINS TO START

COINS PER AUX

LOW TIME ALARM

QUICK RESTART TIME

MODE

DECREASE
(CANCEL)

PN 77108

BLACK

TAN

PURPLE

Function on 20 Position

Terminal Strip

Function

1 24V Hot Red
2 24V Common Purple
3 Main Water Solenoid Black
4 4th Chemical Orange/Blk
5 Rinse Grey
6 2nd Chemical Pink
73rd White

Chemical

8 5th Blue

Chemical
9 Not Used ­10 Timed HotYellow
11 1st Brown

Chemical
12 6th Black/White

Chemical
13 Not Used ­14 Low Dry Red
15 High Dry White
16 24V Common Purple or Blk
17 24V Common
18 24V Common
19 24V COmmon
20 24V Common

Color

Purple or Blk
Purple or Blk
Purple or Blk
Purple or Blk

Pet Dryer

(optional)

RED

RED
PURPLE
PURPLE

ORANGE/BLK

GREY

PINK

WHITE

RED/GREEN

YELLOW

BROWN

BLACK/WHITE

RED
WHITE

PURPLE

10.

11.

12.

13.

14.

15.

16.

1.

2.

3.

4.

5.

6.

7.

8.

9.

In meterbox hull

See DogTe ch-005 for

8 + 10 position rotary

See DogTe ch-006 for

Touchtron doors

PURPLE

18.

19.

BLACK

BLACK-24V Common
RED-Low Dry
WHITE-High Dry

NOTE: For use with 10 position rotary switch. 9th function not

20.

20 position

terminal strip

PN 18721

available with touchtron door
with 8 positon rotary door.

©2018 - GinSan Industries

PRIOR TO JANUARY 1, 2018

Page 6