PROTECTIVE CLOTHING CATEGORY III
2895
REG.EU 2016/425
EN ISO 13688:2013
Internal Code: #
INSTRUCTIONS FOR USE
(PRODUCT CODE: HUAXIN-T)
Marking:
Each clothing is identied with an inside label, this indicates the type of protection offered and other points
of information.
1. Manufacture’s name.
2. CE marking – clothing complies with requirements
for category Ⅲ personal protective equipment according to REGULATION (EU) 2016/425. The test-
ing of the prototype and subsequent CE registra-
tion was made at
(Notify Body Number 2895).
3. Full-body protection “Types” achieved by Xianning
Huaxin Garment Co., Ltd. dened by the European
standards for Chemical Protective Clothing: Type
4 EN14605:2005+A1:2009, Type 5:EN 139821:2004,Type 6:EN 13034:2005. Clothing are tested against biological (EN14126) and radioactive
(EN1073-2) hazards, antistatic EN1149-5 with
2022
Batch#
Shirley® Certication Services
EN1149-1 and must be used with compatible accessories and work particles to be effective.
4. This garment is limited use protective clothing manufactured to meet standard EN ISO 13688:2013
protective clothing general requirements.
Coverall size.
Size Chest (cm) Height (cm)
S 84-92 164-170
M 92-100 170-176
L 100-108 176-182
XL 108-116 182-188
XXL 116-124 188-194
5. Wearer should read these instructions for use.
6. Year of manufacturing.
7. International care symbols: Do not wash, iron, ma-
chine dry, dry clean or bleach. Keep away from
ames and heat.
8. Suitable for single use only-do not re-use.
PERFORMANCE CHART
Fabric Physical Properties Class
Abrasion Resistance
Flex Cracking Resistance
Trapezoidal Tear Resist. MD
XD
Puncture resistance
Tensile Strength MD
XD
Radioactive Protection
Infective Resistance
(solid particles)
Resistance to ignition
Fabric Chemical Properties
Test Method
Resistance to chemical
EN ISO6530
Sulphuric acid 30%
Sodium Hydroxide 10%
o-Xylene
Butance-1-ol
Whole suit test performance
Type 4 Spray Tight
Method as
EN14605:2005+A1:2009
Type 5 Inward leakage
Method as dened by EN
13982-1&2:2004
Type 6 Light spray
Method as dened by
EN13134:2005
En14126:2003
Barrier to infective agents
En1073-2:2002
Barrier to radioactive particulates
EN1149-5/18 Anti-static
Protection against Infective Agents EN14126
EN 530 Meth.2
ISO 7854 B
ISO 9073-4
EN863
ISO 13934-1
EN1073-2:2002
ISO 22612
EN 13274-4
Penetration Repellency
Classe 3
Classe 3
Classe 3
Classe 3
Pass
IL 82/90≤30%&TILS 8/10≤15%
Pass
Pass
Pass
Pass
Pass
Class 1
Class 4
Class 2
Class 2
Class 1
Class 1
Class 1
Class 2
Class 3
Pass
Classe 3
Classe 3
Classe 3
Classe 3
ISO 16603
ISO 16604
EN ISO 22610
ISO 22611
ISO 22612
Class 6
Class 6
Class 6
Class 3
Class 3
Areas of use:
Clothing designed for protection against hazardous
substances and contamination of both product and
personnel. They are typically used for protection
against dry particles and low hazardous splashes and
sprays. The determination for suitability of clothing is
the nal responsibility of the user. The suit may be
contaminated on removal, and should be removed so
as to avoid contamination of the user.
Limitations:
When using the clothing with other PPE and in order to comply fully with EN requirement for Type4/5/6
garment all openings such as wrist, ankles, neck etc.,
should be securely taped. The user shall be the sole
judge of the suitability for the type of protection required and the correct combinations of clothings ac-
cessories and ancillary equipment. Upon contamination, wear or damage, the clothing should be removed
and appropriately disposed of at the earliest opportu-
nity. The wearer should always ensure to check the
integrity of the clothing before wearing it. The possibility of heat stress should be considered in very warm
conditions. Heat stress can be reduced or eliminated
by the appropriate use of undergarments and ventilation equipment. Extreme of heat and cold may adversely affect the performance of this garment. The
clothing should not be used where there is a risk to
certain hazardous chemicals that have not been tested against. Although limited protection can be offered
from various chemicals, please refer to the physical
performance of the clothing in relation to Type4, Type
5 and 6 testing. The user must also wear compatible chemical resistant gloves, boots and respiratory
protection. The gloves should cover the elastic cuffs.
An appropriate size should be selected by the user to
allow for unrestricted movement for the intended risk.
If necessary please contact Manufacturer/Distributor
for advice.
Storage and Disposal:
The clothing can be stored in accordance with normal
storage practices, but we recommend storage in a
dry place away from sources of light, heat and direct
sunlight. Restrictions on the disposal depend solely
on the contamination during use. The manufacturer
cannot accept responsibility for any improper use or
disposal of garments.
Expiration:
It is recommended that the product be used within a
period of 3 years from the date of manufacture/pro-
duction written on the packaging.
Approvals:
CE Approvals by:
(Notied Body: 2895)
Shirley® Port Tunnel Business Park,
Ofce 13 Unit 21, Dublin 17, ROI Ireland
Product code
Lot number
Manufacturer
Consult instructions for use
Date of manufacture
Expiration date
Requirements for category Ⅲ personal protective equipment according to REGULATION (EU)
2016/425
HUAXIN-T(S) (GIMA 21080) TAPED SEAM INSULATION
COVERALL - S - disposable
HUAXIN-T(M) (GIMA 21081) TAPED SEAM INSULATION
COVERALL - M - disposable
HUAXIN-T(L) (GIMA 21082) TAPED SEAM INSULATION
COVERALL - L - disposable
HUAXIN-T(XL) (GIMA 21083) TAPED SEAM INSULATION
COVERALL - XL - disposable
HUAXIN-T(XXL) (GIMA 21084) TAPED SEAM INSULATION
COVERALL XXL - disposable
Xianning Huaxin Garment Co., Ltd.
NO. 86, Guanbu Section,107 National Highway
Xianning city, Hubei Province, China
Made in China
Imported by:
Gima S.p.A.
Via Marconi, 1 - 20060 Gessate (MI) Italy
gima@gimaitaly.com
export@gimaitaly.com
www.gimaitaly.com
2895
M21080-GB-Rev.4-02.22
Loading...