TAPED SEAM BOOT COVERS
Type PB4B-PB6B
2895
EN1149-5/18
INSTRUCTIONS FOR USE
(PRODUCT CODE: TBT)
Marking:
Accessories consisting of :
THD Hood; TBT Boots; TG Gown; TSC Shoe Covers;
TLB Lab Coat; TSL Sleeves; TAP Apron.
Accessories is identied with an inside label, this indicates the type of protection offered and other points
of information.
1. Manufacture’s name.
2. CE marking – Accessories complies with requirements for category Ⅲ personal protective equipment according to REGULATION (EU) 2016/425.
The testing of the prototype and subsequent CE
registration was made at Shirley® Certication Ser-
vices (Notify Body Number 2895).
3. Accessories protection “Types” achieved by Xianning Huaxin Garment Co., Ltd. dened by the European standards for Chemical Protective Clothing:
Type PB 4B EN14605:2005+A1:2009, Type PB 6B:
EN 13034:2005. Accessories are tested against
biological (EN14126), antistatic EN1149-5 with
EN1149-1 and must be used with compatible accessories and work particles to be effective.
4. Size: each accessory has one size.
5. Wearer should read these instructions for use.
6. Year of manufacturing.
7. International care symbols: Do not wash, iron, machine dry, dry clean or bleach. Keep away from
ames and heat.
8. Suitable for single use only-do not re-use.
PERFORMANCE CHART
Fabric Physical Properties Class
Abrasion Resistance
Flex Cracking Resistance
Trapezoidal Tear Resist. MD
XD
Puncture resistance
Tensile Strength MD
XD
Infective Resistance
(solid particles)
Resistance to ignition
Fabric Chemical Properties
Test Method
Resistance to chemical
EN ISO 6530
Sulphuric acid 30%
Sodium Hydroxide 10%
o-Xylene
Butance-1-ol
Whole suit test performance
Type 4 Spray Tight
Method as
EN14605:2005+A1:2009
Type 6 Light spray
Method as dened by
EN13134:2005
En14126:2003
Barrier to infective agents
EN1149-5:2018 Anti-static
Protection against Infective Agents EN14126
ISO 16603
ISO 16604
EN ISO 22610
ISO 22611
ISO 22612
EN 530 Meth.2
ISO 7854 B
ISO 9073-4
EN863
ISO 13934-1
ISO 22612
EN 13274-4
Penetration Repellency
Class 3
Class 3
Class 3
Class 3
Pass
Pass
Pass
Class 6
Class 6
Class 6
Class 3
Class 3
Class 1
Class 4
Class 2
Class 2
Class 1
Class 1
Class 1
Class 3
Pass
Class 3
Class 3
Class 3
Class 3
Areas of use:
Accessories designed for protection against hazardous substances and contamination of both product
and personnel. They are typically used for protection
against dry particles and low hazardous splashes and
sprays. The determination for suitability of accessories is the nal responsibility of the user. The suit may
be contaminated on removal, and should be removed
so as to avoid contamination of the user.
Limitations:
When using the accessories with other PPE and in
order to comply fully with EN requirement for accessories all openings such as wrist, ankles, neck etc.,
should be securely taped. The user shall be the sole
judge of the suitability for the type of protection required and the correct combinations of accessories
and ancillary equipment. Upon contamination, wear
or damage, the accessories should be removed and
appropriately disposed of at the earliest opportunity.
The wearer should always ensure to check the integrity of the accessories before wearing it. The possibility of heat stress should be considered in very warm
conditions. Heat stress can be reduced or eliminated
by the appropriate use of undergarments and ventilation equipment. Extreme of heat and cold may adversely affect the performance of this accessories.
The accessories should not be used where there is
a risk to certain hazardous chemicals that have not
been tested against. Although limited protection can
be offered from various chemicals, please refer to the
physical performance of the accessories in relation
to Type4, Type 5 and 6 testing. The user must also
wear compatible chemical resistant gloves, boots and
respiratory protection. The gloves should cover the
elastic cuffs. An appropriate size should be selected
by the user to allow for unrestricted movement for the
intended risk. If necessary, please contact Manufacturer/Distributor for advice.
Storage and Disposal:
The accessories can be stored in accordance with
normal storage practices, but we recommend storage
in a dry place away from sources of light, heat and
direct sunlight. Restrictions on the disposal depend
solely on the contamination during use. The manufacturer cannot accept responsibility for any improper
use or disposal of accessories.
Expiration:
It is recommended that the product be used within a
period of 3 years from the date of manufacture/production written on the packaging.
Approvals:
CE Approvals by:
Shirley® Technologies (Europe) Limited
(Notify Body: 2895)
Port Tunnel Business Park, Ofce 13 Unit 21,
Dublin 17, ROI Ireland
Product code
Lot number
Manufacturer
Consult instructions for use
Date of manufacture
Expiration date
Requirements for category Ⅲ personal protective equipment according to REGULATION (EU)
2016/425
TBT (21092) TAPED SEAM BOOT COVERS
Type PB4B-PB6B
Xianning Huaxin Garment Co., Ltd.
NO. 86, Guanbu Section,107 National Highway
Xianning city, Hubei Province, China
Made in China
Imported by:
Gima S.p.A.
Via Marconi, 1 - 20060 Gessate (MI) Italy
gima@gimaitaly.com
export@gimaitaly.com
www.gimaitaly.com
2895
M21092-GB-Rev.1-11.21
Loading...