JIANGSU YUYUE MEDICAL EQUIPMENT & SUPPLY CO., LTD.
Sales Center Address: Huanyuan East Road No.1, Xuzhuang Software
Park, Nanjing, Jiangsu Province, P.R. China, 210000
Manufacturing Address: YunYang Industrial Park, DanYang, Jiangsu
Province, P.R. China, 212300
http://www.yuwell.com
0123
131039-0A
8F-3A/8F-3AW/8F-5A/8F-5AW
Oxygen Concentrator
User's Manual
WPP
Do not operate this unit without first
reading and understanding this manual
TABLE OF CONTENTS
SAFETYNOTES………………………………………………1-4
FEATURES……………………………………………………5-7
HANDLING………………………………….………………8-8
OPERATING & INSTALLATION…………………………9-16
MAINTENANCE……………………………………………17-18
SAFETY NOTES
WARNING: INDICATION FOR USE
For avoiding power outage or oxygen concentrator operating failure,
exigent oxygen user and serious patient must equip with reserve oxygen
supply (for example: oxygen cylinder, oxygen bag). This device is to be
used as an oxygen supplement. It is not intended for life supporting, or
life sustaining applications nor does it provide any patient monitoring
capabilities.
WARNING: CONTRAINDICATIONS
The oxygen concentrator is not intended for life supporting or life sustaining
applications, nor does it provide any patient monitoring capabilities.
TROUBLESHOOTING……………………..………………19-22
OTHER ATTENTIONITEMS………………………………23-24
Symbol
WARNING
CAUTION
Describes a hazard or unsafe practice that if not avoided
can result in severe bodily injury, death or property
damage.
Describes a hazard or unsafe practice that if not avoided
can result in minor bodily injury or property damage.
Description
Ⅰ. IMPORTANT MESSAGE
To reduce the risk of electrical shock, DO NOT remove the cabinet. Refer
service to qualified service personnel.
Before operating the device, read and understand this manual.
Ⅱ. BEFORE INSTALLATION
The concentrator should always be kept upright to prevent cabinet damage
while being transported.
If the electrical source power voltage is unstable that beyond normal power
rang, please add the voltage stabilizer.
Please use eligible, safe power set and junction box.
Non-professional people DO NOT open oxygen concentrator's cabinet.
1
SAFETY NOTES SAFETY NOTES
Ⅲ.LOCATING
You may select a room in your house where using your oxygen concentrator
would be most convenient. Your concentrator can easily move from one
room to other room by the wheels.
Be certain to place the device so all sides are at least 10 cm (4 inches) away
from walls, draperies, furniture, or other obstruction. DO NOT place the
unit in a confined area.
Oxygen concentrator must avoid heat source, fire source, wetness,
exorbitant or over-low extra ventricular condition.
Sundries and vessel do not be placed on top of the concentrator.
SAFETY NOTES
NEVER block the air openings of the unit or place it on a soft surface, such
as a bed or couch, where the air opening may be blocked. Keep the openings
free from lint, hair and the like.
Ⅳ. USING
The use of oxygen therapy requires that special care be taken to reduce the
risk of fire. Users MUST NOT SMOKE while using this device. Keep all
matches, lighted cigarettes or other sources of ignition out of the room in
which this product is located. NO SMOKING signs should be prominently
displayed. Textiles and other materials that normally would not burn are
easily ignited and burn with great intensity in oxygen enriched air. Failure to
observe this warning can result in severe fire, property damage and cause
physical injury or death.
For optimum performance, do not open or turn off the concentrator
frequently, reset after 3～5 minutes. Shorter periods of operation may reduce
maximum product life.
A spontaneous and violent ignition may occur if oil, grease or greasy
substances come in contact with oxygen under pressure. These substances
MUST be kept away from the oxygen concentrator, tubing and connections,
and all other oxygen device.
DO NOT use any lubricants unless recommended by manufacturer.
Ⅴ. MAINTENANCE
The oxygen concentrator was specifically designed to minimize routine
preventive maintenance at intervals of once per year. Only professionals of
the healthcare field or persons fully conversant with this process such as
authorized or factory trained personnel should perform preventive
maintenance or performance adjustments on the oxygen concentrator.
Ⅵ. RADIO FREQUENCY INTERFERENCE
This equipment generates, uses and can radiate radio frequency energy and,
if not installed according with the instructions, may cause harmful
interference to other devices in the vicinity. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to other devices, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
● Reorient or relocate the receiving device.
● Increase the separation distance between the equipment.
● Connect the equipment into an outlet on a circuit different from that which
the other device(s) are connected.
● Consult the manufacturer or service technician for help.
Ⅶ. TO REDUCE THE RISK OF BURNS,
ELECTROCUTION, FIRE OR INJURY TO
PERSONS
2
3
SAFETY NOTES FEATURES
Avoid using while bathing. If continuous usage is required by the physician's
prescription:
The concentrator must be located in another room at least 2.5m from the
bath.
DO NOT come in contact with the concentrator while wet.
DO NOT place or store product where it can drop into water or other liquid.
DO NOT reach for product that has fallen into water. UNPLUG
IMMEDIATELY.
A product should NEVER be left unattended when plugged in.
This device is to be used only in accordance with the prescription of a
physician and this User's Manual. If at any time the patient or attendant
concludes that the patient is receiving an insufficient amount of oxygen, the
supplier and/or physician should be contacted immediately. No adjustments
should be made to the flowrate unless prescribed by a physician.
Close supervision is necessary when this product is used near children or
physically-challenged individuals.
Use this product for only intended use as described in this manual.
DO NOT use parts, accessories or adapters other than those authorized by
manufacturer.
DO NOT connect the concentrator in parallel or series with other oxygen
concentrators or oxygen therapy devices.
Use of some administration accessories or certain humidifiers not specified
for use with oxygen concentrator may impair the performance.
In certain circumstances oxygen therapy can be hazardous. Manufacturer
recommends that you seek medical advice before using this product.
Avoid creation of any spark near medical oxygen equipment. This includes
sparks from static electricity created by any type of friction.
The shelf life of the device is 5 years after starting operating.
Ⅰ. SUMMARY
The oxygen concentrator is intended for individual use in the home. It is an
electronically operated device that separates oxygen from room air. It
provides high concentration of oxygen directly to you through a nasal
cannula. Clinical studies have documented that oxygen concentrators are
therapeutically equivalent to other types of oxygen delivery systems.
This user's manual will tell you about your concentrator and will serve as a
reference as you use your concentrator.
Ⅱ.CHARACTERS
Complete plastic out shell, safe and reliable.
Timing accumulates function, show total operating hours through the display
screen.
Timing turns off function using convenience.
Compressor pressure relief valve help the device safer.
Power interruption alarm function.
Device failure alarm function (including pressure/cycle failure, compressor
failure, low oxygen concentration).
Compressor with over heat protect function to gain in safety of the
compressor and the concentrator.
*Nebulizing function (8F-3AW, 8F-5AW).
Remote control function.
Ⅲ.SPECIFICATIONS
1. Maximum Recommend Flow Rate: 3L/min (8F-3A, 8F-3AW);
5L/min (8F-5A, 8F-5AW)
2. Flow Range: 0~3L/min (8F-3A, 8F-3AW); 0~5L/min (8F-5A, 8F-5AW)
3. Change in maximum recommended flow when back pressure of 7kPa is
applied: 0.5L/min
4
5
FEATURES FEATURES
4. Oxygen Concentration:
93%±3% (8F-3A, 8F-3AW); 95.5%～87% (8F-5A, 8F-5AW)
5. Output Pressure: 20～ 50kPa (8F-3A, 8F-3AW); 40～70kPa (8F-5A, 8F-
5AW)
Oxygen Con ce nt ration: %
100
95
90
85
80
8F-3A
8F-3AW
8F-5A
75
70
65
1 2 3 4 5 6
Figure 1
8F-5AW
Oxygen Flow:
L/min
14. Altitude: Up to 1828 meters (6000 ft) above sea level without
degradation of concentration levels. From 1828 meters (6000 ft) to 4000
meters (13129 ft) below 90% efficiency.
15. Safety System:
● Over Current or Connection Loosen: Unit Shut Down
● Compressor Over Hot: Unit Shut Down
● Pressure, Cycle Failure: Alarming and Shut Down
● Compressor Failure: Alarming and Shut Down
● Low Oxygen Concentration
16. Minimum Operating Time: 30minutes
17. Electric classification: class II equipment, type BF applied part
18. Work system: work continuously.
19. Normal Operating Condition:
● Temperature range: 10℃～40℃ (50℉～104℉)
● Relative humidity: 30%～75%
● Atmosphere pressure: 860hPa～1060hPa (12.47psi～15.37psi)
CAUTION:
7. Pressure Relief Mechanism Operational at: 250kPa±25kPa
(36.25psi±3.63psi)
8. Sound Level:
(8F-3A, 8F-3AW) Average (Front Side): 42dB(A), whole unit: 46dB(A);
(8F-5A, 8F-5AW) Average (Front Side): 48dB(A), whole unit: 52dB(A).
9. *Maximum Nebulizing Rate: ≥0.15mL/min ( 8F-3AW, 8F-5AW)
10. Power Supply:
□AC120V±10% □AC220V±10% □AC230V±10%
□50Hz±2% □60Hz±2%
20. Oxygen Output Temperature: ≤ 46℃
21. Cannula length DO NOT more than 15.2m (50ft) and no twist.
22. Storage and Transportation Condition:
● Temperature range: -20℃～60℃ (-4℉～140℉)
● Relative humidity: 10%～93% Non-condensing.
● Atmosphere pressure: 700hPa～1060hPa (10.15psi～15.37psi)
CAUTION:
11. Input Power: 230VA (8F-3A, 8F-3AW);400VA (8F-5A, 8F-5AW)
12. Net Weight: 11.8kg (8F-3A, 8F-3AW );15.5kg (8F-5A, 8F-5AW)
13. Dimension: W39cm(15.4 )×D24.5cm(9.7 )×H50cm(19.7 )
〃 〃 〃
When storage/transportation condition is lower than 5℃ ,
please put the device in normal operating condition more
than 4 hours before operating.
The device should be stored with no strong sunlight, no
corrosive gas and well ventilated indoor area. The device
must be transported and used in the vertical position only.
6 7
HANDLING
OPERATING ＆ INSTALLATION
Ⅰ. UNPACKING Ⅰ. FEATURE VIEW
CAUTION:
1. Check for any obvious damage to the carton or its contents. If damage is
evident, please notify the carrier or local dealer.
2. Remove all loose packing from the carton.
3. Carefully remove all the components from the carton.
Ⅱ.INSPECTION
1. Examine exterior of the oxygen concentrator for nicks, dents, scratches or
other damages.
2. Inspect all components.
Unless use the oxygen concentrator, retain containers and
packing materials for storage until use of the concentrator is
required.
Control Buttons
Display Panel
Flowmeter
Flowmeter Knob
Humidifier
*Nebulizer Outlet
(8F-3AW, 8F-5AW)
Oxygen Outlet
Wheel
Ⅲ.STORAGE
1. Store the repackaged oxygen concentrator in a dry area.
2. DO NOT place other objects on top of the repackaged concentrator.
Filter Cap
Breaker
8 9
Figure 2: FullV iew (Front)
Power Switch
Power Cord
Figure 3: FullV iew (Back)
OPERATING ＆ INSTALLATION
OPERATING ＆ INSTALLATION
Plus Timing
Remote Control
Receiver
Oxygen Inlet
Oxygen Outlet
Maximum Level
Minimum Level
Minus Timing On/Off Button
Timing
Setting
Figure 5: Humidifier Components
Elapsed
Time
Figure 4: Control Panel
Green
Light
Yellow
Light
Safety Valve
Cap
Humidifier Tube
Bottle
Humidifier Filter Element
Ⅱ.PREPARE WORK
1.Unscrew the bottle from the humidifier clockwise. Fill the bottle with pure
water (or distilled water) to the level between MAXIMUM and MINIMUM.
DO NOT fill humidifier bottle over MAXIMUM level. (Figure 5)
2. Screw securely the bottle back counterclockwise.
(Recommend to use Yuwell Humidifier p/n: 2.05.014.114)
3. Connect the power supply.
Red
Light
CAUTION:
NOTE: Concentrator may be used during the initial start warm-up time
(approximately 30 min) while waiting for the O2 purity to reach maximum.
1) If the concentrator has a damaged cord or plug, if it is not
working properly, if it has been dropped or damaged, or
dropped into liquid, call Qualified Service Personnel for
examination and repair.
2) Keep the cord away from HEATED or HOT surfaces.
3) Do not move or relocate concentrator by pulling on the
cord.
4) Do not use extension cords with this unit.
Ⅲ. OXYGEN ABSORBING OPERATION
1. FLOWRATE (Figure 6 )
Turn the flowrate knob to the setting prescribed by your physician or
therapist.
NOTE: To properly read the flowrate, locate the prescribed flowrate line on
the flowmeter.
Next, turn the flow knob until the ball rises to the line.
Now, center the ball on the L/min line prescribed.
Flowmeter Window
Flowrate Indicator
Float Ball
Big
Flowmeter Knob
Small
Figure 6: Setting Flowrate
10 11
OPERATING ＆ INSTALLATION OPERATING ＆ INSTALLATION
CAUTION:
Meanwhile, humidifier bottle will have air bubble around the sieve core.
Then, oxygen comes from the oxygen outlet.
2. Connect nasal oxygen cannula to oxygen outlet, the other end match the
patient.
Note: The time of absorbing oxygen and the flowrate range according to the
doctor's advices.
If the flowrate on the flowmeter ever falls below 0.5L/min,
check tubing or accessories for blocked or kinked tubing or
a defective humidifier bottle.
*Ⅳ.NEBULIZING OPERATION(8F-3AW, 8F-5AW)
Fill proper medicinal liquid in the nebulizing cup (Please follow the doctor's
advices or don't exceed the maximum reticle of the nebulizing cup).
Upward pull out the nebulizing cover on the nebulizing interface. (Figure 7)
Counterclockwis
Nebulizing Cap
Nebulizing Interface
Figure 7: Nebulizing
Connect the air hose to neblizing cup and nebulizing interface, then turn on
the power of the oxygen concentrator, now can begin nebulizing therapy
immediately.
When drug nebulizaing have finished, turn the nebulizing cover right to
nebulizing interface for tightening. If you won't breathe oxygen, please turn
off the oxygen concentration.
Pull out the air hose, pull the mouthpiece, downward pull the nebulizing
cup's cap, empty remained medicinal liquid in the nebulizing cup, then wash
the air hose, mouthpiece, nebulizing cup's cap, nebulizing baffle, nebulizing
cup, ripple tube, T-piece, etc , with pure water or immerge them in warm
water for about 15 minutes. In order to wash them healthy, you may add
some vinegar in water. (NOTE: DO NOT cook the accessories above for
wash or wash them with boiled water, in case they'll distort when heating).
After finishing cleaning, must dry all the components before storage.
(Nebulizer installment is shown in figure 8).
NOTE: The timing for using nebulizer must follow the doctor's advices.
Mouthpiece
Cap
Baffle
T-piece
Cup
Figure 8: Nebulizer Components
Ripple tube
Air hose
Ⅴ. ALARM SIGNAL
Concentrator has following failure alarm function:
1) Pressure and cycle failure
2) Compressor failure
3) Low oxygen concentration
Note：All the alarms of the device are low priority.
12 13
OPERATING ＆ INSTALLATION
OPERATING ＆ INSTALLATION
Ⅴ. MAINTENANCE
Initial startup of the concentrator
When the unit is turned on, the green light will come on (O concentration
greater than 82%). After 5 minutes, the oxygen sensor will be operating
normally and will control the indicator lights depending on oxygen
concentration values. The explanations of the indicator light functions are as
follows.
Explanation of the indicator light
Symbol
I/O
SYSTEM OKAY
(O concentration is greater than 82%.)
2
O concentration is greater than 50% and less
2
than 82%.
SYSTEM FAILURE
(O concentration is less than 50%; Or,
2
High/Low cycle pressure failure alarm; Or,
Compressor circuit failure alarm )
Status
Alarm signal register
1. O concentration is greater than 82%. - Green light illuminates, and panel
2
shows “－－－－H elapsed time H”. Normal Operation.
2. O concentration is greater than 50% and less than 82%. －－ Green and
2
yellow light illuminate, and panel shows “－－－－H elapsed time H”. Call
Supplier Immediately. You may continue to use the concentrator unless
instructed otherwise by your supplier. Be certain that BACKUP OXYGEN
is nearby.
NOTE: Concentrator will reach to most stable state after warm-up
(approximately 30 minutes).
2
Indicator lights
Green
Green, Yellow
Red
3. O concentration is less than 50%. －－ Red light illuminates, continuous
2
audible alarm sounds, panel shows word “LO” and the unit shutdown.
Switch immediately to backup oxygen supply. Call supplier immediately.
4. Low/High pressure, cycle failure alarm － － Red light illuminates,
continuous audible alarm sounds, and panel shows word“E1” or “E2”. Total
unit shutdown. Switch immediately to backup oxygen supply. Call supplier
immediately.
5. Compressor failure alarm － － Red light illuminates, continuous audible
alarm sounds, and panel shows word“E3” or “E4”. Total unit shutdown.
Switch immediately to backup oxygen supply. Call supplier immediately.
Ⅵ.SETTING TIMING UP
User can press the timing button to setting the operating time in 0~2 Hours.
When it start working, the display shows “－－－－H elapsed time H ”, it
means that timing function is closed. It will work continually until power
supply cuts off.
Press the “+” button once, operation time increases 1 minute, holding the
button more than 1.5 seconds it will increase continually.
Press the “-” button once, operation time decrease 1 minute, holding the
button more than 1.5 seconds it will decrease continually.
The device will auto turn off and the display will show “00:00H” when
finishing timing. Reset timing function.
Ⅶ.TURNNING OFF
During using the device, user can press down the on/off button, mounted in
control panel, to stop/start oxygen supply.
Take off nasal oxygen cannula from oxygen outlet first, turn off power
switch, and then cut off the power source.
14 15
OPERATING ＆ INSTALLATION
MAINTENANCE
Ⅷ.SYMBOLS
Symbol
Description
Alternating current
Class Ⅱ Equipment
OFF (power
disconnection from
the mains)
Breaker
No Smoking
Keep Dry
Symbol
ON (power connection
to the mains)
4
Ⅸ.Remote Control
Use infrared remote controller to operate the device. (Figure 9)
Transmit Window
Plus Timing
On/Off
Description
Consult the manual
Type BF Applied par
Keep Up
Fragile
Stacking Limitation
NOTE: Power should be disconnected before beginning preventive
maintenance on the concentrator. The concentrator is specifically designed
to minimize routine preventive maintenance at intervals of once per year. In
places with high dust or soot levels, maintenance may need to be performed
more often. The following must be performed at a minimum of one year in
service to assure years of additional reliability.
Ⅰ.CLEAN CABINET
WARNING:
Clean the cabinet with a mild household cleaner and non-abrasive cloth or
sponge at least one time a month. Do Not drop any liquid into the seam of
the device.
CUT OFF the power supply first to avoid electrical shock.
DO NOT remove device cabinet.
Ⅱ.CLEAN OR REPLACE FILTER
Please clean or replace the filters in time, it's very important to protect
compressor and to extend the device life.
Disassembly Filter
Remove the filter cover and take out the filter.
Minus Timing
Figure 9: Remote Controller
Note: During remote control operating, the remote controller must be toward
the receiver which is located in the control panel.
Filter Cover
Figure 10: Remove Filter
Filter
16 17
MAINTENANCE
TROUBLESHOOTING
Clean Filter
1) Clean the filter with a soft cleaner or wash in warm soapy water and rinse
thoroughly.
2) DRY the filter thoroughly before reinstallation.
3) The filter must clean or replace.
CAUTION:
DO NOT operate the concentrator without installing filter,
or while filter is wet. These actions could permanently
damage the concentrator.
Clean Humidifier
1) Remove the humidifier bottle from the humidifier cap then clean the bottle.
2) Remove the humidifier tube and diffuser then clean them.
Figure 11 Figure 12
*Clean Neublizer
Note: Must clean the neublizer after using.
1) After nebulizing, remove the neublizer from oxygen concentrator. Turn
off the oxygen concentrator, disconnect the hose, remove the cap,
disassembly the neublizer as shown in Figure 8.
2) Put all the nebulizer components to warm water for 15 min. (Add some
vinegar to the warm water, if necessary.)
DO NOT cook or use boiling water to clean the nebulizer components.
3) DRY all the components thoroughly before storage.
TROUBLESHOOTING GUIDE
故障现象
Symptom
Power Interruption
Alarm:
Press the power on
switch on the
control panel,
buzzer alarming,
display not lit,
device not work.
Concentrator is
working, the
operating sound is
normal, the
flowmeter knob
can be adjusted but
no oxygen output
or weak output.
Probable cause
1) Power cord and wall
outlet have poor contact.
2) Wall outlet no power
output.
3) Low power of wall
outlet.
4) Breaker reset button
raised.
5) If the device is still not working, please contact the
supplier.
1) Leakage between
humidifier bottle and cap.
2) The safety valve of
humidifier is opened.
The connection between
oxygen output and
humidifier is leaking.
4) The accessory (nasal
cannual, mask, humidifier,
tubing…., etc.) is leaking.
5) If the phenomenon is still appeared, please contact
the supplier.
Solution
1) Re-insert the power cord
into wall outlet securely.
2) Change to another wall
outlet.
3) Change to another wall
outlet. Do not use any
extension cord.
4) Press down the breaker
reset button.
1) Re-insert the power cord
into wall outlet securely.
2) Change to another wall
outlet.
3) Re-install the humidifier
tubing.
4) Replace the leaked
accessory.
18
19
TROUBLESHOOTING TROUBLESHOOTING
故障现象 故障现象
Symptom Symptom
Concentrator is
working, but green
light, yellow light
illuminate at the
same time.
Concentrator is not
working, the red
light illuminate,
buzzer alarm, the
display show
“LO”.
Concentrator is not
working, the red
light illuminate,
buzzer alarm, the
display show “E1”.
Concentrator is not
working, the red
light illuminate,
buzzer alarm, the
display show “E2”.
Concentrator is not
working, the red
light illuminate,
buzzer alarm, the
display show “E3”.
Probable cause Probable cause
1) 50% ≤ Oxygen
Concentration ≤ 82%.
2) Oxygen flow rate over
the maximum recommend
flow rate: 3L/min(8F-3A,
8F-3AW);
5L/min(8F-5A, 8F-5AW).
3) If the phenomenon is still appeared, the device can be
used but please contact the supplier.
1) Oxygen Concentration
≤ 50%.
2) Oxygen flow rate over
the maximum recommend
flow rate: 3L/min(8F-3A,
8F-3AW);
5L/min(8F-5A, 8F-5AW).
3) If the phenomenon is still appeared, stop using the
device, please contact the supplier immediately.
1) System cycle pressure
is too low.
) If the phenomenon is still appeared, stop using the
device, please contact the supplier immediately.
1) System cycle pressure
is too high.
1) Compressor circuit is
opened.
Solution Solution
1) Clean or replace the filter.
2) Adjust the flow rate only
under the advice of a
physician.
1) Clean or replace the filter.
2) Turn off and re-turn on
the device. Adjust the flow
rate only under the advice
of a physician.
1) Clean or replace the filter.
1) Stop using the device,
please contact the supplier
immediately.
1) Stop using the device,
please contact the supplier
immediately.
Concentrator is not
working, the red
light illuminate,
buzzer alarm, the
display show “E4”.
The nasal cannula
is fogged with
vapor or full of
liquid drops.
(Remove the vapor
or liquid drops
method: Turn on
the device and
connect the tubing
to the oxygen
outlet. Use your
finger to block and
release the end of
the tubing several
times to remove
the moisture and
liquid.)
1) Compressor circuit is
closed.
1) Poor ventilation around
the around the device, so
operating temperature is
too high.
2) The water which added
to humidifier is too hot.
3) Add too many water
into humidifier.
4) The device stops
suddenly during operating.
5) Accessory is connected
to the device. The tubing
is kinked and the device
stops suddenly.
6) Cooling fan which
mounted inside the device
stop running or rotate
slowly, make the operating
temperature is too hot.
7) If the phenomenon is still appeared, the device can
be used but please contact the supplier.
1) Stop using the device,
please contact the supplier
immediately.
1) Make sure the device is
at least 10 cm away from the
walls, other jam or heater.
2) Add cold water to
humidifier.
3) Water added should
between the maximum
and minimum levels in
humidifier.
4) Turn off the device
immediately. Restart the
device to remove the
moisture and liquid.
5) Smooth the nasal
cannula and tubing.
6) Replace the cooling fan.
Note: Cut off the power
first. And perform by
qualified personnel only.
20 21
TROUBLESHOOTING
OTHER ATTENTION ITEMS
故障现象
Symptom
*During nebulizing
operating, the
nebulizing
rate is too small
or not working.
(8F-3AW, 8F-5AW)
Remote control
malfunction.
CAUTION:
If you have all other problems, TURN OFF the concentrator
first, use your reserve oxygen supply, and contact the
supplier immediately.
Probable cause
1) Neublizer components
installed incorrect.
2) Neublizer deformed due
to washing or disinfection.
3) Neublizer output is
blocked.
4) Add too much medicinal
liquid into the nebulizer.
5) If the phenomenon is still appeared, stop using
nebulizer, please contact the supplier.
1) Do not use the remote
controller in the receiving
area.
2) Low battery.
Solution
1) Install the nebulizer
correctly. (Figure 8).
2) Replace the nebulizer.
3) Clean or replace the
nebulizer.
4) Add medicinal liquid
into the nebulizer
according to physician
prescription and not over
the maximum level.
1) Operate the remote
controller in the front
side of the device.
2) Replace the battery in
the remote controller.
Ⅰ. GAS PASS OPERATION SKETCH MAP
Air
Oxygen/Nitrogen
Separation
Oxygen
Product
Tank
Nasal Oxygen
Cannula
Filter
Nitrogen
Pressure
Regulator
Humidifier
Compressor
Molecular
Sieve
Commute Valve
Bacilli
Filter
Oxygen
Outlet
Heat Exchanger
Valve Assembly
Muffler
Flowmeter
Check Valve
22 23
OTHER ATTENTION ITEMS
Ⅱ. ELECTRICAL RATIONALE
Display Board
Breaker
~
Fan
Main Board
Compressor
Oxygen Sensor
Exchange
ValveⅠ
Ⅲ.PACKING LIST
1. Oxygen Concentrator: 1 unit
2. User Manual: 1 piece
3. Filter: 1 piece
*4. Nebulizer (8F-3AW, 8F-5AW): 1 set
Ⅳ.DEVICE DISPOSAL
Contact the local city or town offices for proper disposal instructions for
oxygen concentrator.
Exchange
Valve Ⅱ
24
Loading...