Gima OPTOMETRIC CHART, MIXED DECIMAL"" CHART User guide

Standard viewers

Tel.: [phone] – Fax: [phone]

and Optotypes

Instruction and maintenance

manual

GIMA spa

Via Marconi 1 – 20060 Gessate (MI) – Italia

E-mail: [e-mail] – www.gimaitaly.com

INTRODUCTION

Dear Customer,

your choice of our appliance means, for our Company,your particular
recognition of the care of our designers, in the achievement of an ergonomic,
reliable and pleasant design product.

We would thank you in advance for your choice and we are at your complete
disposal for everything you need.

You are kindly requested to pay particular attention to this manual, before
using the item, as it contains important recommendations on the correct
installation use and maintenance of the product.

Have a good work!

PRODUCT DESTINATION

Our appliance has been suitably designed to obtain the best backlight of the
X-ray films to read and value them at one's best.

This machine must only be used for the purpose for which it was
designed.
All other uses must be considered dangerous.

In this case the manufacturer can't be considered responsible for any
damage caused by an incorrect use.

INFORMATION AND TECHNICAL DATA

Our appliance doesn't need any kind of maintenance.

In particular, the chassis is made of oven epoxy powder coated aluminium
section, that doesn't let the structure become wasted.

Besides, the neon tubes are placed in order to avoid totally any shadow's
zone.

Specifications could be changed anytime.

Technical data:

CODE

Viewers Electrical

supply

Power External dimensions

mm

BFAL 43.43 OR 1 panel 230V 50-60Hz 30W 430x430x12

BFAL 43.70 OR/VE/OV 1,5 panels 230V 50-60Hz 36W 670x430x12

BFAL 43.90 OR/VE/OV 2 panels 230V 50-60Hz 60W 970x430x12

BFAL 43.120 OR/VE/OV 3 panels 230V 50-60Hz 72W 1270x 430x12

BFAL 43.150 OR/VE/OV 4 panels 230V 50-60Hz 116W 1580x430x12

BFAL 86.120 OR 2 x 3 panels 230V 50-60Hz 2x72W 2 x (1270x430x12)

BFAL 86.150 OR 2 x 4 panels 230V 50-60Hz 2x116W 2 x (1580x430x12)

CODE

Luminous
optotypes

Electrical

supply

Power External dimensions

mm

BFAL 27.67AL Mixed decimal 3 mt 230V 50-60Hz 18W 295 x 675 x 12

BFAL 27.67BL Monoyer 3 mt 230V 50-60Hz 18W 295 x 675 x 12

BFAL 27.67CL Children 3 mt 230V 50-60Hz 18W 295 x 675 x 12

BFAL 27.67DL Mixed decimal 5 mt 230V 50-60Hz 18W 295 x 675 x 12

BFAL 27.67EL Armagnac 5 mt 230V 50-60Hz 18W 295 x 675 x 12

BFAL 27.67FL Children 5 mt 230V 50-60Hz 18W 295 x 675 x 12

PACKAGING HANDLING

After taking away the packaging, do not leave the different elements (carton
boxes, plastic bags, polystirene, etc.) in the enviroment and do not leave
them in children hands.

Anyway do not throw away the packaging before veryfing the correct
operation of the device, as in case of giving it back to the supplier, the device
has to be put in its own original packaging.

All the different elements of the packaging, have to be handled following the
local Directives regarding the disposal of the waste.

GENERAL WARNING

After removing the packaging, check that the product has not been damaged
in transit.

In case of doubt, do not attempt to repair or use the machine. Seek advice
from a suitably qualified person. Packaging materials (plastic bags,
polystyrene rubber, etc.) must be kept away from children, as they could
cause harm.

This machine must only be used for the purpose for which it was designed.

All other uses must be considered dangerous.

The safe use of any electrical appliance involves the observance of certain
basic rules, in particular:

o do not touch the appliance with damp hands;

o do not use the appliance while bare-foot;

o do not pull the plug from power socket by the power cord of the

appliance itself;

o do not expose the appliance to adverse elements (sun, rain, etc.);

o do not let the children use the advice.

The manufacturer can't be considered responsible for damages caused by an
incorrect use of the product.

SPECIAL WARNINGS

The electrical safety of this appliance is only guaranteed when it is correctly
installed and connected to the earthed system, according to the latest issue
of the Regulations Conformity with these requirements must be ensured and,
in case of doubt, seek advice from a suitable qualified person.

Our Company can't be held responsible for any damage caused because the
appliance has not been installed and earthed correctly.

Besides it is important to respect the following recommendations:

o check that the current carrying capacity of the wirings and socket are

suitable for the maximum power of the device as shown on the label. In

case of doubt, seek advice from a suitable qualified person

o to avoid dangerous overheating, it is advisable to fully unroll the power

cord

o do not leave the appliance plugged in when unnecessarily.

If power cord becomes damaged, replace it promptly with the power cord:
EN 60 320-C15 - outlet CEI 23-16/VII (SCHUKO CEE 7-S.S. VII).

The manufacturer can't be considered responsible for any damage
caused by an incorrect installation and earthing of the appliance.

OPERATING

The viewer/optotype has been adjusted and tested in the Factory, and it
doesn't need any other adjustmen or technical control before operating
phase.

To install the appliance take care to the following directions:

1. the viewer/optotype has to be mounted on a steady and straight wall,
trough suitable bearings placed distant between themselves as the
distance of the holes on the back of the advice;

2. do not install the viewer/optotype near the water as it could cause short
circuit;

3. do not install the device near heat sources;

4. connect the viewer/optotype to the plug trough the supplied power cord,
paying attention that it is not damaged;

5. turn on the main switch from O to I;

6. once turned on the switch, place the X-ray under the frame of the
viewer.

MAINTENANCE / CLEANING

The viewer/optotype needs no maintenance except for routine cleaning which
is easily done because every part is easy to reach.

Before any phase of maintenance, do not leave the appliance plugged.

Do not use any solvent to clean the appliance.

GUARANTEE

We always guarantee our devices for 24 months, from the date of the
purchase.

Parts acquired from other manufacturers have the same guarantee that is
given us by the manufacturer.

Parts subject to normal wear as plastic parts, glass, neon, starter, etc., are
excluded from the gurantee.

Shipping costs are paid by the Customer.

The repairing actions do not modify the expiry date of guarantee.

The Customer must send the device to manufacturer, with a photocopy of the
purchase invoice, where is signed the date of the purchase and the appliance
number.

Further claims from the purchaser for reimbursement of damages not
attributable to the manufacturer, are obviously not taken in consideration.

DECLARATION OF CONFORMITY

EC 2007/47, EC 2006/95, EC 2004/108 Directives

BIEFFE ITALIA s.r.l.

declare under our responsibility that the product

standard VIEWER

code BFAL 43.43 OR; BFAL 43.70 OR/VE/OV; BFAL 43.90 OR/VE/OV;

BFAL 43.120 OR/VE/OV; BFAL 43.150 OR/VE/OV;

BFAL 86.120 OR; BFAL 86.150 OR

luminous OPTOTYPE

code BFAL 27.67AL; BFAL 27.67BL; BFAL 27.67CL;

BFAL 27.67DL; BFAL 27.67EL; BFAL 27.67FL

non luminous OPTOTYPE

code BFAL 27.67A; BFAL 27.67B; BFAL 27.67C;

BFAL 27.67D; BFAL 27.67E; BFAL 27.67F

is in conformity with the following standards or

other normative document

EC Directive 2007/47 medical device of Class I

EC Directive Low Voltage 2006/95

EC Directive Electromagnetic Compatibility 2004/108

Striano (NA), January 2015

BIEFFE ITALIA s.r.l.

Dr. Flavio Ferrazzano

BIEFFE ITALIA s.r.l. weiko

®

Legal office: Viale Lincoln, 178 - 81100 Caserta (Italy)

Factory:Via Palma, 284 - 80040 Striano-Na (Italy)

Tel.: [phone] – Fax: [phone]

[e-mail] - www.weiko.com

Bank:

CARIPARMA c/c 000056503302

ABI 06230 CAB 14910 CIN E

IBAN IT75 E062 30 14910 000056503302

C.C.I.A.A. 147379

Trib. S. Maria C.V. 16412

P. IVA 02220390617