Gima ULTRA SLIM LED LIGHT BOX 42x36 cm, DESKTOP ULTRA SLIM LED LIGHT BOX 42x36 cm User guide
Page 1
1
Page 2
ENG INDEX
1. Introduction
2. Important advice note
3. Product destination
4. Information
5. Technical data
6. Packaging handling
7. General warning
8. Special warning
9. Installation
10. Operating
11. Maintenance/Cleaning directions
12. Guarantee
13. EC Declaration of Conformity
Please read this manual with special care, before installing and operating the
device.
ATTENTION: this symbol indicates the manual's sections that the user must
fully understand and follow in order to avoid any potential damage to people
and also to the equipment itself.
3
Page 3
1. INTRODUCTION
Dear Customer,
your choice of our appliance means, for our Company, your particular recognition of the care of our
designers, in the achievement of an ergonomic, reliable and pleasant design product.
We would thank you to trust our Company and we are at your complete disposal for everything you
need.
2. IMPORTANT ADVICE NOTE
You are kindly requested to pay particular attention to this manual, before using the
appliance, as it contains important recommendations on the correct installation, use and
maintenance of the product.
As a matter of fact it is the shortest way of communication between the Supplier and the
end User (p. 7.2.3 UNI EN ISO 13485:2012).
Have a good work!
3. PRODUCT DESTINATION
Our appliance, both in wall and table version (workstation), has been suitably designed to obtain
the best backlight of the X-ray films to read and value them at one's best.
This machine must only be used for the purpose for which it was designed.
All other uses must be considered dangerous.
In this case the manufacturer can't be considered responsible for any damage caused by an
incorrect use.
4
Page 4
4. INFORMATION
Our SLIM LED viewers use the LEDs technology, the most advanced actually used in the lighting
field.
The SLIM LED viewers are designed and assembled to work with separated or non separated
panels, so that the panels can be set on either separately or all together.
Compared to the ones on sale, with high performance the SLIM LED viewer, has a special
keyboard, placed on its down side, that allows the following operative systems:
a. TRADITIONAL: manual switching on/off
b. FAS (Film Automatic Switching): automatic switching on/off, at the positioning/removal of the
X-ray film; in the wall mounting version it is an optional while it is normally installed on
Workstations.
c. DIMMER: luminance adjustment with range by 30% up to 100%. It is normally installed on all
versions.
The use of LEDs technology allowing to obtain the following advantages:
1) OPERATIVE
luminance increase
uniform distribution of light with temperature of color more suitable to read the X-Ray films
complete elimination of light flickering
2) ECONOMICAL
viewer's average life increase (average life of LEDs 80.000/100.000 hours)
reduction of electrical power consumption
3) ADDITIONAL ADVANTAGES
depth of viewer only 3 cm
vibrations and shock resistance, due to the use of “solid state” components
eco-compatibility, as all the components are for limited environmental impact
The chassis is made of oven epoxy powder coated aluminum section, that doesn't let the structure
become wasted.
The SLIM LED viewer is produced both in wall and table version (workstation).
5
Page 5
5. TECHNICAL DATA
CODE
Wall version
Electrical supply
Power
VA
External dimensions
mm
BF LED 50.1
1 LED panel
110V-230V 50-60Hz
40
457 x 30 x 505
BF LED 50.2
2 LED panels
110V-230V 50-60Hz
80
817 x 30 x 505
BF LED 50.3
3 LED panels
110V-230V 50-60Hz
120
1177 x 30 x 505
BF LED 50.4
4 LED panels
110V-230V 50-60Hz
160
1537 x 30 x 505
BF LED 50.1 F
1 LED panel FAS
110V-230V 50-60Hz
40
457 x 30 x 505
BF LED 50.2 F
2 LED panels FAS
110V-230V 50-60Hz
80
817 x 30 x 505
BF LED 50.3 F
3 LED panels FAS
110V-230V 50-60Hz
120
1177 x 30 x 505
BF LED 50.4 F
4 LED panels FAS
110V-230V 50-60Hz
160
1537 x 30 x 505
CODE
Built-in version
Electrical supply
Power
VA
External dimensions
mm
BF LED 50.1 F I
1 LED panel FAS
110V-230V 50-60Hz
40
484 x 40 x 532
BF LED 50.2 F I
2 LED panels FAS
110V-230V 50-60Hz
80
844 x 40 x 532
BF LED 50.3 F I
3 LED panels FAS
110V-230V 50-60Hz
120
1204 x 40 x 532
BF LED 50.4 F I
4 LED panels FAS
110V-230V 50-60Hz
160
1564 x 40 x 532
CODE
Table version
WORKSTATION
Electrical supply
Power
VA
External dimensions
mm
BF LED 50.1 F T1
1 LED panel
110V-230V 50-60Hz
40
457 x 30 x 505
BF LED 50.1 F T2
2 x 1 LED panels
110V-230V 50-60Hz
2 x 40
2 x (457 x 30 x 505)
BF LED 50.1 F T3
3 x 1 LED panels
110V-230V 50-60Hz
3 x 40
3 x (457 x 30 x 505)
F = FAS (Film Automatic Switching): in the wall mounting version it is an optional while it is
normally installed on Workstations.
Specifications could be changed anytime.
6. PACKAGING HANDLING
After taking away the packaging, do not leave the different elements (carton boxes, plastic bags,
polystirene, etc.) in the environment and do not leave them in children hands, as they can be
dangerous.
Anyway do not throw away the packaging before verifying the correct operation of the device, as in
case of giving it back to the supplier, the device has to be put in its own original packaging.
All the different elements of the packaging, have to be handled following the local Directives
regarding the disposal of the waste.
6
Page 6
If it is necessary to dispose the SLIM LED viewer, at the end of its useful life, or for other reasons,
it is important to consider that the SLIM LED viewer has to be disposed following the directions of
the Directives that regulate the electromechanical/electrical devices, for which the same Directives
require to reutilization/recycle the parts of the device, to avoid damages to the environment and
consequently for the people health.
Ignoring the Directives regarding the disposal of the waste, please contact the qualified local
Authorities.
7. GENERAL WARNING
After removing the packaging, check that the product has not been damaged in transit.
In case of doubt, do not attempt to repair or use the machine. Seek advice from a suitably qualified
person. Packaging materials (plastic bags, polystyrene rubber, etc.) must be kept away from
children, as they could cause harm.
This machine must only be used for the purpose for which it was designed.
All other uses must be considered dangerous.
The safe use of any electrical appliance involves the observance of certain basic rules, in
particular:
o do not touch the appliance with damp hands;
o do not use the appliance while bare-foot;
o do not pull the plug from power socket by the power cord of the appliance itself;
o do not expose the appliance to adverse elements (sun, rain, etc.);
o do not let the children use the advice.
The manufacturer can't be considered responsible for damages caused by an incorrect use of the
product.
8. SPECIAL WARNING
In case of any doubt on the safety of the advice, do not use it, and ask to a qualified person.
The electrical safety of this appliance is only guaranteed when it is correctly installed and
connected to the grounded network, according to the latest issue of the Regulations Conformity
with these requirements must be ensured and, in case of doubt, seek advice from a suitable
qualified person.
Our Company can't be held responsible for any damage caused because the appliance has not
been installed and earthed correctly.
7
Page 7
Besides it is important to respect the following recommendations:
o check that the current carrying capacity of the wirings and socket are suitable for the
maximum power of the device as shown on the label. In case of doubt, seek advice from a
suitable qualified person
o to avoid dangerous overheating, it is advisable to fully unroll the power cord
o do not leave the appliance plugged in when unnecessarily.
If power cord becomes damaged, replace it promptly with the power cord:
EN 60 320-C15 - outlet CEI 23-16/VII (SCHUKO CEE 7-S.S. VII).
The manufacturer can't be considered responsible for any damage caused by an incorrect
installation and earthing of the appliance.
9. INSTALLATION
The SLIM LED viewer has been tested in the factory, and its luminance has been adjusted at
100% of its maximum and it doesn't need any other adjustmen or technical control after installation
phase.
To install the SLIM LED viewer in wall version (Workstation) take care to the following directions:
1. the SLIM LED viewer has to be mounted on a steady and straight wall, trough suitable
bearings placed distant between themselves as the distance of the holes on the back of the
advice;
2. do not install the SLIM LED viewer near the water as it could cause short circuit;
3. do not install the device near heat sources;
4.
To install the SLIM LED “BUILT-IN” version, please take care of the instructions put in the box.
To install the SLIM LED viewer in table version (Workstation) please take care to the special
manual, where are described the assembling directions to place the viewer on the special support.
8
Page 8
10. OPERATING
The SLIM LED viewer has a main switch O/I placed on the right side at the bottom and has also a
little keyboard to start up the operating phase (see below figure).
D B A C E
The viewer has normally supplied with luminance adjusted at 100% maximum conditions.
To set on the appliance operate as follows:
1. connect the SLIM LED viewer to the plug trough the supplied power cord, paying attention
that it is not damaged;
2. turn on the main switch from O position on the right side to I position; in this mode starts to
flash the light (A) in the middle of the keyboard and is possible to operate in different modes:
TRADITIONAL
In the condition reported in the aforesaid point 2., with light (A) flashing, press the ON/OFF key
(D).
When the light (A) stops flashing but keeps lighted, press the A/M key (E).
The viewer lights on with normal luminance at the 100%.
Then go to operate according point 3.
FAS (Film Automatic Switching)
In the condition reported in the aforesaid point 2., with light (A) flashing, press the ON/OFF key
(D).
The light (A) stops flashing but keeps lighted.
The viewer is ready to work in FAS mode with automatic switching on/off, at the
positioning/removal of the X-ray film.
Then go to operate according point 3
DIMMER
The luminance, either in TRADITIONAL mode or in FAS mode, can be tuned in a range
between 30% and 100% of its maximum value, press the left key (B) to decrease the value of
luminance or press the right key (C) to increase it.
3. insert the X-ray film under the frame of the SLIM viewer.
To install the SLIM LED viewer in table version (workstation) – after assembling it on the suitable
equipped support (see specific manual) – put it on the desk in the preferred position following the
above points 1, 2 and 3.
The viewer in table version has the chance to be adjusted in its space positioning (up/down, side to
side rotation, forward/backward rotation) (see the special manual) to allow the operator to work in
the most comfortable conditions.
9
Page 9
11. MAINTENANCE / CLEANING DIRECTIONS
The SLIM LED viewer doesn't need any advanced maintenance, but, if it is out of order, verify and
eventually change the fuse if damaged (1 panel 1A, 2 panels 1A, 3 panels 2A, 4 panels 2A).
If the appliance persists in being out of order, ask to your supplier.
The SLIM LED viewer needs only the routine cleaning which is easily done because every part is
easy to reach.
Before any phase of maintenance, do not leave the appliance plugged.
Do not use any solvent to clean the appliance.
12. GUARANTEE
The manufacturer guarantees the good quality of the parts of the device, assuring, during the
warranty period, to repair or replace as soon as possible, defected parts, if it depends on the
manufacturer itself or on the Force Majeure.
We always guarantee our devices for 24 months, from the date of the purchase.
Parts acquired from other manufacturers have the same guarantee that is given us by the
manufacturer.
Parts subject to normal wear as plastic parts, glass, neon, starter, etc., are excluded from the
gurantee.
Shipping costs are paid by the Customer.
All risks during the transport are under responsibility of the Customer.
The repairing actions do not modify the expiry date of guarantee.
The Customer must send the device to manufacturer, with a photocopy of the purchase invoice,
where is signed the date of the purchase and the appliance number.
Further claims from the purchaser for reimbursement of damages not attributable to the
manufacturer, are obviously not taken in consideration.
10
Loading...