Gima BOOT COVERS User guide

BOOT COVERS - Type PB6B
BOOT COVERS - Type PB6B with anti-slip sole

2895

EN1149-5/18

2022

INSTRUCTIONS FOR USE
(PRODUCT CODE: 04BT)
Marking:

Accessories consisting of :
04HD Hood; 04BT Boots; 04G Gown; 04SC Shoe
Covers; 04LB Lab Coat; 04SL Sleeves; 04AP Apron.
Accessories is identied with an inside label, this in­dicates the type of protection offered and other points
of information.

1. Manufacture’s name.

2. CE marking – Accessories complies with require­ments for category Ⅲ personal protective equip­ment according to REGULATION (EU) 2016/425.
The testing of the prototype and subsequent CE
registration was made at Shirley® Certication Ser­vices (Notify Body Number 2895).

3. Accessories protection “Types” achieved by Xian­ning Huaxin Garment Co., Ltd. dened by the Eu­ropean standards for Accessories: Type PB 6B:EN
13034:2005. Accessories are tested against bio-

logical (EN14126:2003) and antistatic (EN1149-

5:2018), and must be used with compatible acces-

sories and work particles to be effective.

4. Size: each accessory has one size.

5. Wearer should read these instructions for use.

6. Year of manufacturing.

7. International care symbols: Do not wash, iron, ma­chine dry, dry clean or bleach. Keep away from
ames and heat.

8. Suitable for single use only-do not re-use.

PERFORMANCE CHART

Fabric Physical Properties Class
Abrasion Resistance
Flex Cracking Resistance
Trapezoidal Tear Resist. MD

XD
Puncture resistance

Tensile Strength MD

XD

Infective Resistance

(solid particles)

Resistance to ignition
Fabric Chemical Properties
Test Method
Resistance to chemical
EN ISO 6530
Sulphuric acid 30%
Sodium Hydroxide 10%
o-Xylene
Butance-1-ol
Whole suit test performance
Type 6 Light spray
Method as dened by

EN 13034:2005
En 14126:2003

Barrier to infective agents
EN 1149-5:2018 Anti-static
Protection against Infective Agents EN14126
ISO 16603
ISO 16604
EN ISO 22610
ISO 22611
ISO 22612

EN 530 Meth.2
ISO 7854 B
ISO 9073-4

EN863

ISO 13934-1

ISO 22612

EN 13274-4
Penetration Repellency

Class 3
Class 3
Class 3
Class 3

Pass

Pass
Pass

Class 6
Class 6
Class 6
Class 3
Class 3

Class 1
Class 4
Class 2
Class 2
Class 1
Class 1
Class 1
Class 3

Pass

Class 3
Class 3
Class 3
Class 3

Areas of use:

Accessories designed for protection against hazard­ous substances and contamination of both product
and personnel. They are typically used for protection
against dry particles and low hazardous splashes and
sprays. The determination for suitability of accesso­ries is the nal responsibility of the user. The suit may

be contaminated on removal, and should be removed

so as to avoid contamination of the user.

Limitations:

When using the accessories with other PPE and in
order to comply fully with EN requirement for acces­sories all openings such as wrist, ankles, neck etc.,
should be securely taped. The user shall be the sole
judge of the suitability for the type of protection re-

quired and the correct combinations of accessories
and ancillary equipment. Upon contamination, wear

or damage, the accessories should be removed and

appropriately disposed of at the earliest opportunity.
The wearer should always ensure to check the integ­rity of the accessories before wearing it. The possibil­ity of heat stress should be considered in very warm
conditions. Heat stress can be reduced or eliminated
by the appropriate use of undergarments and venti­lation equipment. Extreme of heat and cold may ad­versely affect the performance of this garment. The
accessories should not be used where there is a risk

to certain hazardous chemicals that have not been

tested against. Although limited protection can be
offered from various chemicals, please refer to the
physical performance of the accessories in relation
to Type6 testing. The user must also wear compati­ble chemical resistant gloves, boots and respiratory
protection. The gloves should cover the elastic cuffs.
An appropriate size should be selected by the user to
allow for unrestricted movement for the intended risk.
If necessary please contact Manufacturer/Distributor
for advice.

Storage and Disposal:

The accessories can be stored in accordance with
normal storage practices, but we recommend storage
in a dry place away from sources of light, heat and
direct sunlight. Restrictions on the disposal depend
solely on the contamination during use. The manu­facturer cannot accept responsibility for any improper
use or disposal of accessories.

Expiration:

It is recommended that the product be used within a
period of 3 years from the date of manufacture/pro­duction written on the packaging.

Approvals:

CE Approvals by:
(Notied Body: 2895)
Shirley® Port Tunnel Business Park,
Ofce 13 Unit 21, Dublin 17, ROI Ireland

Product code

Lot number

Manufacturer

Consult instructions for use

Date of manufacture

Expiration date

Requirements for category Ⅲ personal protec­tive equipment according to REGULATION (EU)

2016/425

04BT (GIMA 21090) BOOT COVERS - Type PB6B
04BT (GIMA 21091) BOOT COVERS - Type PB6B

with anti-slip sole

Xianning Huaxin Garment Co., Ltd.
NO. 86, Guanbu Section,107 National Highway
Xianning city, Hubei Province, China
Made in China

Imported by:

Gima S.p.A.

Via Marconi, 1 - 20060 Gessate (MI) Italy
[e-mail]
[e-mail]

www.gimaitaly.com

2895

M21090-GB-Rev.2-02.22