Gill Electronics Teslink WPT503CM Installation Information

INSTALLATION INFORMATION FOR

INSTALLERS

WIRELESS POWER TRANSMITTER

(THROUGH SURFACE)

Model Number: WPT503CM

OF DOCUMENT

IMPORTANT – PURPOSE OF DOCUMENT

THIS DOCUMENT IS FOR USE ONLY BY ORIGINAL EQUIPMENT MANUFACTURERS (OEMs) WHO PURCHASE THE
REFERENCED TESLINK™ COMPONENTS FROM GILL ELECTRONICS, INCORPORATED OR ITS AFFILIATES (GILL). NEITHER
THIS DOCUMENT NOR THE INFORMATION IN THIS DOCUMENT IS INTENDED FOR DISTRIBUTION TO, OR USE BY, END
USERS OF OEM PRODUCTS WHICH INCORPORATE TESLINK
COMPONENTS FROM GILL, EACH OEM ASSUMES, AND SHALL HAVE SOLE AND FULL RESPONSIBILITY FOR, PROVIDING
APPROPRIATE INSTRUCTIONS FOR USE OF SUCH OEM PRODUCTS.

GILL ASSUMES THAT ALL OEMs WHO PURCHASE FROM GILL AND WHO USE THIS DOCUMENT HAVE EXPERTISE IN THE
USE OF ELECTRICAL DEVICES AND COMPONENTS, INCLUDING THE EXPERTISE NECESSARY TO (i) DETERMINE WHETHER
OR NOT TESLINK™ COMPONENTS ARE SUITABLE FOR USE WITH THE OEM’s PRODUCT, AND (ii) PROPERLY AND SAFELY
CONFIGURE AND INSTALL TESLINK™ COMPONENTS. ACCORDINGLY, THIS DOCUMENT IS INTENDED ONLY AS A HELPFUL
SUPPLEMENT FOR USE BY THE OEM AND NOT AS A SUBSTITUTE FOR THE OEM’s EXPERTISE OR THE OEM’s
RESPONSIBILITY FOR PROPER AND SAFE DESIGN OF ITS PRODUCT AND INSTALLATION AND USE OF TESLINK
COMPONENTS. IF ANY OEM USING THIS DOCUMENT LACKS SUCH EXPERTISE OR DOES NOT AGREE TO THE FOREGOING
LIMITED PURPOSE STATED FOR THIS DOCUMENT, SUCH OEM SHOULD IMMEDIATELY NOTIFY GILL IN WRITING TO THAT
EFFECT AND SHOULD NOT USE THIS DOCUMENT. PRICES AND OTHER TERMS AND CONDITIONS FOR SALE OF TESLINKTM
COMPONENTS TO ANY OEM ARE GOVERNED BY SEPARATE DOCUMENTS ISSUED OR MADE AVAILABLE TO THE OEM BY
GILL, INCLUDING THE INVOICE ISSUED BY GILL AND THE STANDARD TERMS AND CONDITIONS OF SALE.

TM

COMPONENTS (END USERS). BY PURCHASING TESLINK™

TM

Page 1

If you have need assistance or have questions, email [e-mail]

SAFETY INFORMATION

GILL EXPECTS THAT THE INSTALLER WILL INCLUDE APPROPRIATE SAFETY WARNINGS AND INFORMATION FOR END
USERS OF ALL PRODUCTS WHICH INCORPORATE TESLINK
INCLUDE THOSE SET FORTH BELOW AND OTHER WARNINGS AND INFORMATION AS THE INSTALLER DETERMINES
NECESSARY AND APPROPRIATE.

DANGER

To reduce the risk of electrical shock:

• Always unplug the appliance from the electrical outlet before removing

• Do not reach for an appliance that has fallen into water – unplug it immediately

• Do not disassemble or modify any part of this appliance

• Do not install this product in any ferrous, non-ferrous, or electrically conductive surface

WARNING

To reduce the risk of burns, fire, electrical shock, or injury to persons:

• This product should not be used by children or persons with disabilities that may hinder their ability to understand all
product information and use the product safely. Close supervision is necessary when this product is used near
children or persons with disabilities

• Use this product only for its intended use as described in this manual

• Never operate this product if it has a damaged housing, cord, plug cable, or if wet

• Keep cord away from heated surfaces and liquid

• Do not operate where aerosol products are being used or oxygen is being administered

• This product is designed for indoor use only. Do not install or use this product outdoors

• Do not use this appliance with an extension cord or overloaded electrical outlet

• Do not place or leave metallic objects between the charging surface and device being charged

• This product should be kept a minimum of 35mm from all animate objects when in power transfer mode/charging

mode.

TM

COMPONENTS. SUCH WARNINGS AND INFORMATION MUST

IMPORTANT SAFETY INSTRUCTIONS

1. SAVE THESE INSTRUCTIONS – This manual contains important safety and operating instructions for resonant chargers

Models: WPT503CM

2. Before using the resonant charger, read all instructions and cautionary markings on the resonant charger, power supply,
and product using the resonant charger

3. CAUTION – To reduce damage or risk of injury, charge only A4WP/ Rezence-certified products.

Page 2

If you have need assistance or have questions, email [e-mail]

FCC & INDUSTRY CANADA COMPLIANCE

C & INDUSTRY CANADA COMPLIANCE

The installer shall inform end users of the following to the extent applicable:
This device complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio

frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This transmitter must not be co­located or operating in conjunction with other antenna or transmitter.

Changes or modifications not expressly approved by Gill Electronics, Incorporated could void the user’s authority to operate the
equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna/device

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

This Class B digital apparatus complies with Canadian ICES-001-V4.

EUROPEAN DECLARATION OF CONFORMITY

We, Gill Electronics, Incorporated, 5271 Plainfield Ave. NE. Grand Rapids, MI 49525, USA, declare under our sole responsibility that
the product Wireless Power Transmitter - WPT503CM To which this declaration relates is in conformity with the following standard(s)
or other normative document(s):

EN 55011
EN 300 328
EN 300 330
EN 301 328
EN 301 489
EN 609501
EN 61000-6-1
EN 62311
EN 60950

Following the provisions of Electromagnetic Compatibility, R&TTE Emissions, and Safety directive(s).
The Technical Construction File is maintained at:

Gill Electronics Inc.
5271 Plainfield Ave. NE
Grand Rapids, MI 49525 USA

Page 3

If you have need assistance or have questions, email [e-mail]