Gilbarco MRIR11 User Manual

Introduction

MDE-4017
TIRIS Transmitter/Receiver Mat Reader
Assembly Kit C00016-XXX Installation
May 2001

Purpose of this Manual

This manual provides instruction for installing TIRIS™ Mat Reader Assembly Kit C00016­XXX.
The TIRIS™ option allows customers to automatically authorize non-cash sales using a hand­held transponder tag.

Important Notice

This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
na
ry
The long term characteristics or the possible physiological effects of radio frequency electromagnetic fields have not been investigated by Underwriters’ Laboratories, Inc. (UL
i
01

Required Reading

Before installing the equipment, the i nstaller must read, understand, and follow:
this manual
NFPA 70, The National Electric Code
applicable federal, state and local codes and regulations
Failure to do so may adversely effect the safe use and operation of the equipment.
eli
m
r
P
®
).
MDE-4017 TIRIS™ Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001 Page 1

Related Documents

Installer must obtain, read and understand all site preparation documentation provided by the point of sale company authorizing the installation before attempting to install this equipment.
In addition, the installer must be familiar with the information in the following documents.
Document Number Title GOLD Library
MDE-3110 PC-Based G-SITE System Installation Manual G-SITE MDE-3111 PC-Based G-SITE System Start-Up and Service Manual • G-SITE
• Service Manual
MDE-3620 Gilbarco POS Console Site Preparation Manual Site Prep

Required Tools

The following equipment is needed to install all TIRIS mat reader kits:
drill motor and bits
needle nose pliers
®
screwdriver, Phillips
®
Zircon
stud/bracket finder
head

Parts Lists

C00016-006 Kits contain the following parts:
Description Part Number Quantity
box, interface assembly M01814A001 1 tape, neoprene foam M01870B001 2 channel, plastic filler M01871B001 1 cable, mat reader drive M01872A001 1 tape, acrylic foam K85492-72 1 power supply M01878B001 1 jack, jump, push-to-start Q11011-01 1 cable, data, CAT-5 Q13482-06 1 clamp, cable, stick on, small Q13459-01 3 document, installation (this document) MDE-4017 1 diagram, block and/or interconnect M0187 3 0
P
The following components are also required.
Description Part Number Quantity
graphics MR01002G003 1 reader, mat, TIRIS device
Note: The Mat Reader is delivered with the graphics in place.
e
r
liminary
M01787B001 1
4/01
2
Page 2 MDE-4017 TIRIS™ Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001

Important Safety Information

This section introduces the hazards and safety precautions associated with installing, inspecting, maintaining or servicing this product. Before performing any task on this product, read this safety information and the applicable sections in this manual, where additional hazards and safety precautions for your task will be found. Electrical shock could occur and cause death or serious injury if these safe service procedures are not followed.

Preliminar y Precautions

Read, understand and follow this manual and any other labels or related materials supplied with this equipment.

Follow the Regulations

There is ap plicable information in: NFPA 70: National Electrical Code (NEC); OSHA regulations; and federa l, state, and local codes which must be followed. Failure to install, maintain or service this equipment in accordance with these codes, regulations and standards may lead to legal ci ta ti ons wi th penalties or affect the safe use and operation of th e equi pment .
1
24/0
5/
0
Preliminary
Page 3 MDE-4017 TIRIS Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001

Safety Symbols and Warning Words

Alert Symbol

This safety alert symbol is used in this manual and on warning labels to alert you to a precaution which must be followed to prevent potential personal safety hazards. Obey safety directives that follow this symbol to avoid possible injury or death.

Signal Words

These signal words used in this manual and on warning labels tell you the seriousness of particular safety hazards. The precautions that follow must be followed to prevent death, injury or damage to the equipment.
DANGER
This signal word is used to alert you to a hazard or unsafe practice which will result in death or serious injury.
WARNING
This alerts you to a hazard or unsafe practice that could result in death or serious injury.
CAUTION
This signal word de signa tes a h azard or unsa fe prac tice w hich may res ult in minor injury.
CAUTION
When used by itself, C AUTION de signates a hazard o r unsafe pra ctice whic h may result in
property or equipment damage.

Proper Grounding is Required

Proper grounding is required for safe operation. See installation manual and applicable NEC,
NFPA and local electrical codes for requirements.

Avoid Pinched Wires

Pinched or cut wires (cables) may damage components. Exposed wires could create sparks and
P
electrical shorts when applying power.

Other Useful Safety Information

Replacement Parts

Use only genuine Marconi replacement parts. Using parts other than genuine Marconi
replacement parts could create a safety hazard, violate national, state and local regulations or
void warranty.
e
r
4/01
liminary
2
Page 4 MDE-4017 TIRI S Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation May 2001

Installation

Note: All installation work is to be accomplished between the hours specified by the point of
sale company authorizing the installation.
Install Mat Reader assembly according to the following:
1 Collect and arrange all tools and equipment.
2 If necessary for installation of kit in area specified by point of sale company, remove
advertisement panels, saving all mounting hard ware for re-u se later.
Note: Make note of non-reu sab le fasteners, ensuring adequate replacements are avail abl e f o r
later use.

Setting Baud Rate

1 Remove Mat Reader Interface Box cover to access logic board.
Figure:
Mat Reader Interface Box Cover
24/0
2 Locate jump jacks on logic board for M at Reader.
Figure:
Jump Jacks for Baud Rate Setting
5/
0
cover screw
1
BAUD 1 2 4
Preliminary
Page 5 MDE-4017 TIRIS Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001
3 Set the jump jacks as follows (see Figure: Jump Jacks for Baud Rate Setting on page 5).
CAUTION
Electrostatic Discharge Damage
Working on electronics w ithout co nnecting to a gro und or discharging static can damage electronic parts. Use a wrist strap.
Mat Reader Baud Rates
Baud Rate (Note) BAUD 1 BAUD 2 BAUD 4
4800 OUT OUT O UT 2400 IN OUT O UT 1200 OUT IN O UT
300 IN IN OUT 38400 OUT OU T IN 19200 IN OU T IN
9600 OUT IN IN 4800 IN IN IN
Note: 4800 is the default value and the Mat Reader value.
4 If not daisy chaining Mat Reader Interf ace Boxes, reinstall cover.
Note: Daisychaining is connecting the output from one Interface Box to the input of another.

Addressing Logic Board - Only for Da is ycha ining

Address for Mat Reader must ma tch addr ess on pre viousl y ins tall ed Mat Reader. Follow these steps:
1 Access logic board for Mat Reader being installed.
2 Locate jump jacks on previously installed Mat Reader logic board M01803A001.
Figure:
Jump Jacks for Address Setting
e
liminary
4/01
2
r
ADDR 1 2 4 8 16
P
Page 6 MDE-4017 TIRI S Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation May 2001
3 Note position of jump jacks on previously installed Mat Reader logic board, and set jump
jacks on board for Mat Reader being installed to match address on logic board.
CAUTION
Electrostatic Discharge Damage
Working on electronics w ithout co nnecting to a gro und or discharging static can damage electronic parts. Use a wrist strap.
Mat Reader Addresses
Address on Logic Board M01803A001 ADDR 1 ADDR 2 ADDR 4 ADDR 8 ADDR 16
0 OUT OUT OUT OUT OUT 1 IN OUT OUT OUT OUT 2 OUT IN OUT OUT OUT 3 IN IN OUT OUT OUT 4 OUT OUT IN OUT OUT 5 IN OUT IN OUT OUT 6 OUT IN IN OUT OUT 7 INININOUTOUT 8 OUT OUT OUT IN OUT
9 IN OUT OUT IN OUT 10 OUT IN OUT IN OUT 11 IN IN OUT IN OUT 12 OUT OUT IN IN OUT 13 IN OUT IN IN OUT 14 OUTINININOUT 15 IN IN IN IN OUT 16 OUT OUT OUT OUT IN 17 IN OUT OUT OUT IN 18 OUT IN OUT OUT IN
5/
19 IN IN OUT OUT IN
0
20 OUT OUT IN OUT IN 21 IN OUT IN OUT IN 22 OUTININOUTIN
Preliminary
23 IN IN IN OUT IN 24 OUT OUT OUT IN IN 25 IN OUT OUT IN IN 26 OUT IN OUT IN IN 27 IN IN OUT IN IN 28 OUT OUT IN IN IN 29 IN OUT IN IN IN 30 OUTININININ 31 IN IN IN IN IN
24/0
1
4 Reinstall c over.
Page 7 MDE-4017 TIRIS Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001

Mounting Mat Reader Interface Box

1 Determine the location for the installation of indoor equipment.
Note: Refer to site pr ep document pr ovi ded by point of sale compan y and keep in mind overal l
length of cable to connect Mat Reader Interface Box to Mat Reader.
2 Use a Zircon stud/bracket finder to ensure no electrical conduits or pipes are located inside of
wall where the Mat Reader Interface Box is to be mounted. Also, ensure the Mat Reader Interface Box i s to be located where studs or wall (conc rete/brick/drywall) mollys can b e used for mounting.
3 Mark and drill holes. Insert wall mollys as required.
CAUTION
Do not use t he Mat Reader Interface Box as a drill guide. It may be used as a template to mark the holes to be drilled.
4 Use appropriate mounting hardware to secure the Mat Reader Interface Box to the wall.
Figure:
Mat Reader Interface Box Mounting Holes
P
e
r
mounting holes
4/01
liminary
2
Page 8 MDE-4017 TIRI S Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation May 2001

Connecting Data Cables to Mat Reader Interface Box

Run both power and data cables to port end of Mat Reader Interface Box (see Figure: Mat
Reader Interface Box Mounting Holes on page 8) as follows.
1 Connect the P3 end of the ribbon cable (M01872A001) to the RFID interface port (P3) .
2 Connect the J1end of the CAT-5 cable (Q13482-06) to the J1IN port.
Figure:
Connecting to Mat Reader I nterface Box
Connect power supply here.
Connect J1 end of CAT-5 cable here.
Connect P3 end of ribbon cable here.
If daisychaining, connect CAT-5 from J1IN on other interface box here.
1
24/0
5/
0
Preliminary
Page 9 MDE-4017 TIRIS Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001

Connecting Data Cables from the Mat Reader Interface Box

1 Position Mat Reader face down.
Figure:
2 Select side for ribbon cable (M01872A001) connection based on counter top configuration
requirements.
3 Install strip of acrylic foam tape (K85492-72) in base of channel on side selected for ribbon
cable.
Bottom Side of Mat Reader
bottom side of neoprene foam tape (flipped over to show connector)
7-pin connector
channel for ribbon cable (acrylic foam tape in place)
bottom side of Mat Reader
4 Peel second release liner, exposing adhesive.
4/01
5 Carefully connect the P1/P2 end of the ribbon cable (M01872A001) to the back side of the
Mat Reader.
Note: The cable can be plugged in from either side. Since the cable is not keyed, the
orientation does not matter. Be sure the cable will be flat and not twisted once the Mat Reader is face up.
e
liminary
2
r
P
Page 10 MDE-4017 TIRIS Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation May 2001
Figure: Connecting to Mat Reader
bottom side of neoprene foam tape
ribbon cable connected to 7­pin connector
unused channel filled with plastic filler channel and covered by neoprene foam tape
6 Install neoprene foam tape (M01870B001) over ribbon cable and sides of channel. Foam tape
should fit snugly into cutout of surrounding foam tape backer.
7 On unused cable channel, install plastic filler channel (M01871B001).
8 Install remaining neop rene f oam tap e (M0 1870B001) over fill er cha nnel. Foam tape sh ould f it
snugly into cutout of surrounding foam tape backer.
9 Gently turn the Mat Reader to the face-up position.
Figure:
Mat Reader - Face Up
1
24/0
5/
0
Preliminary
10 Connect the lo ose end of the CAT-5 cable to the RS-232-1 or RS-232-2 port on the back of t he
G-SITE system.
Note: The exact G-SITE system port depends on the G-SITE system configuration.
Page 11 MDE-4017 TIRIS Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation May 2001

Connecting Power Supply

Connect the power supply (M01878B001) provided with kit as shown.
1 Plug the wall-mounted transformer into the AC power outlet.
Note: This AC power outlet must be on the same circuit as the G-SITE system.
2 Connect the plug end of the power supply cable to the JDC1 port on the Mat Reader Interface
Box (see “Figure: Connect ing to Mat Reade r Interface Box ” on page 9).
Figure:
wall-mounted transformer
Power Supply (M01878B001)
plugs into AC power outlet
liminary
plugs into JDC1 port
4/01
2
e
r
P
Page 12 MDE-4017 TIRIS Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation May 2001

Completing Installation

Figure: Mat Reader Connections
power supply
Mat Reader
ribbon cable
1 Dress all cables and secure with stick on cable clamps (Q13459-01).
1
2 Clean up the work area.
3 Go to Commissio ning and Warranty Information on page 14.
interface box
CAT-5 cable connects here
24/0
5/
0
Preliminary
Page 13 MDE-4017 TIRIS Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation May 2001

Commissioning and Warranty Information

Upon completion and testing the Mat Reader system, the installing contractor must call the Marconi Commerce Systems Call Center @ 1-888-800-7498 to register the installation and activate the warranty. Note the installed unit’s full Model Number (C00016-XXX) and serial number before making this call.
All Mat Readers have a one-year parts only warranty.
Note: Parts are to be returned through and obtained from the local Marconi distributor.
Labor warranty, if any, is unit and customer specific.
Marconi Commerse Systems strongly recommends using only Marconi trained ASCs (Authorized Service Contractors) to perform service on the units. Use of non-authorized service personnel to repair or se rvice the se units may void warranty. Call your local distributor for service.
y
im
el
r
P
TRIND® is a registered trademark of Marconi Commerce Systems Inc.
®
Phillips UL Zircon
is a registered trademark of Phillips Screw Company.
®
is a registered trademark of Underwriters Laboratories, Inc.
®
is a registered tradema r k of Zircon International Inc.
nar
i
4/01
2
© 2001 Marconi Commerce Systems Inc. 7300 West Friendly Avenue Post Office Box 22087 Greensboro, North Carolina 27420 Phone (336) 547-5000 http://www.marconicommerce.com Printed in the U.S.A. MDE-4017 TIRIS Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001
Loading...