
RFID Multi-ISO Protocol
http://www.gigatms.com.tw
Introduction:
The MP101A is a RFID Module for all
13.56-MHz RFID/contactless standard
MP101Asupports and compatibles with all
secured baseband ISO standards including
Type A, Type B, and Smartlabel ISO15693.
The MP101A is well suited for mobile
to its low power consumption and low
from 5V. The on-chip 3.3V regulators are
stabilize the chip’s power, and
power to the external companion
120mA.
The MP101A is ideal for access control,
Automatic Fare Collection (AFC), ticketing,
mobile solutions
Applications:
● Pre-payment, Ticketing
● Prepaid parking / meal coupon
● Multi-application: Tracking, Retail, Customer,
Leisure, Gambling
Ordering information:
● MP101AR-00----RS232 Interface
● MP101AU-00----USB Virtual COM
● MP101AH-00----USB HID Interface
The
global
due
voltage
to
supply the
up to
well as
and
Features:
● Enhanced anti-collision
handling
● Full 3DES/AES crypto
● USB and RS232 Interface,
● T=CL ISO7816 interface
● Full access to data of
security and
● Card TYPE
ISO 14443A
MIFARE™Standard, MIFARE
IFARE Ultralight
C,MIFARE DESFire®,MIFARE
ISO 14443B
Smartcard ISO14443B, SRI4K,
ISO 15693
SIC5600, ICODE-SLI, ICODERead payware and paypass and
ISO7816 contact smart card
NFC TAG 1~4 supportive
ISO18092 Felica READ UID
※Specification is subject to change
for multi-card
N,8,1
ss memory, high
-based cards
MIFARE Ultralight, M
EV1,
SRI512
-L, ICODE-SLIS
-passport
notice.
We welcome OEM inquiries
♦ Custom design manufacturing is available
♦ Custom device programming is available
♦ Call factory for other configuration
8F.,NO.31, LANE 169, KANG-NING
-CHIH,TAIPEI,TAIWAN
886-2-26954214
886-2-26954213
e-

RFID Multi-ISO Protocol
http://www.gigatms.com.tw
Federal Communication Commission Interference S
This equipment has been tested and found to comply with the limits for
tatement
a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To as
sure continued compliance, any changes or modifications not expressly
approved by the party responsible for compliance could void the user's authority to operate
this equipment. (Example - use only shielded interface cables when connecting to computer
or peripheral devices).
This device complies with P
art 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
We welcome OEM inquiries
♦ Custom design manufacturing is available
♦ Custom device programming is available
♦ Call factory for other configuration
8F.,NO.31, LANE 169, KANG-NING
-CHIH,TAIPEI,TAIWAN
886-2-26954214
886-2-26954213
e-