GIGAMEDIA GGM AXA1EMK2K, GGM AXA1MFK2K, GGM AXA1MFK2KW, GGM AXA1EMK2KW User Manual

Standalone Keypad Access Control

Centrale de contrôle d’accès autonome

User Manual - Manuel Utilisateur

GGM AXA1EMK2K
GGM AXA1MFK2K
GGM AXA1EMK2KW
GGM AXA1MFK2KW

Please read the manual carefully before use this unit
Veuillez lire ce manuel avec attention avant d’utiliser le produit.

GGM AXA1 - Series access control User Manual

Standalone Keypad Access Control

1. Packing List

• 1 Keypad

• 1 User manual

• 1 Screw driver Ø 20mm×60mm,Special for keypad

• 2 Rubber plug Ø 6mm×30 mm, used for fi xing

• 2 Self tapping screws Ø 4mm×28 mm, used for fi xing

• 1 Star screws Ø 3mm×6mm, used for fi xing

Please ensure that all the above contents are correct.
If any are missing please notify the supplier of the unit.

2. Quick Reference Programming Guide

To enter the programming mode

* Master code #

999999 is the default factory master code

To exit from the programming mode

*

Note that to undertake the following programming the master user must be logged in

To change the master code

0 New code # New code #

The master code can be 6 to 8 digits

To add a PIN user.

1 User ID number #

The ID number is any number between 1 & 2000.
The PIN is any four digits between 0000 & 9999
with the exception of 1234 which is reserved.

Users can be added continuously without exiting programming mode

To add a card user

1 Read Card #

Cards can be added continuously without exiting programming mode

To delete a PIN or a card user.

User ID number

2

2 Read Card #

Users can be deleted continuously without exiting programming mode

To unlock the door for a PIN user

Enter the PIN then press

To unlock the door for a card user

Present the card

PIN #

# for a PIN user or

for a card user

#

3

EN

GGM AXA1 - Series access control User Manual

EN

3. Description

The unit AXA1 is single door multifunction standalone access controller or a Wiegand output
keypad or card reader. It is suitable for mounting either indoor or outdoor in harsh environ­ments. It is housed in a strong, sturdy and vandal proof Zinc Alloy electroplated case which
is available in either a bright silver or matt silver fi nish. The electronics are fully potted so
the unit is waterproof and conforms to IP68. This unit supports up to 2000 users in either
a Card, 4 digit PIN, or a Card + PIN option. The inbuilt card reader supports 125KHZ EM
cards,13.56MHz Mifare cards. The unit has many extra features including lock output current
short circuit protection, Wiegand output , and a backlit keypad. These features make the unit
an ideal choice for door access not only for small shops and domestic households but also for
commercial and industrial applications such as factories, warehouses, laboratories, banks
and prisons.

4. Features

• Waterproof, conforms to IP68

• Strong Zinc Alloy Electroplated anti-vandal case

• Full programming from the keypad

• 2000 uses, supports Card, PIN, Card + PIN

• Can be used as a stand alone keypad

• Backlight keys

• Wiegand 26 input for connection to external reader

• Wiegand 26 output for connection to a controller

• Adjustable Door Output time, Alarm time, Door Open time

• Very low power consumption (30mA)

• Fast operating speed, <20ms with 2000 users

• Lock output current short circuit protection

• Easy to install and program

• Built in light dependent resistor (LDR) for anti tamper

• Built in buzzer

• Red, Yellow and Green LEDS display the working status

5. Specifi cations

Operating Voltage DC 12V±10%
User Capacity 2000
Card Reading Distance: 3-6 cm
Active Current:
Idle Current: 25±5 mA
Lock Output Load: Max 3A
Alarm Output Load: Max 20A
Operating Temperature: -45°C ~ 60°C
Operating Humidity: 10%- 90% RH
Waterproof: Conforms to IP68
Adjustable Door Relay time: 0 -99 seconds
Adjustable Alarm Time: 0- 3 minutes
Wiegand Interface: Wiegand 26 bit
Wiring Connections: Electric Lock, Exit Button, External Alarm, External reader

60mA

<

4

GGM AXA1 - Series access control User Manual

6. Installation

• Remove the back cover from the keypad using the supplied special screw driver

• Drill 2 holes on the wall for the Self tapping screws and I hole for the cable

• Put the supplied rubber bungs to into the two holes

• Fix the back cover fi rmly on the wall with 2 Self tapping screws

• Thread the cable through the cable hole

• Attach the keypad to the back cover.

1 2 3

4 5 6

7 8 9

0 #

*

7. Wiring

Colour Function Description

Pink BELL_A Doorbell button one end

Pale blue BELL_B Doorbell button to the other end

Green D0 WG output D0
White D1 WG output D1

Grey ALARM Alarm negative(alarm positive connected 12 V+)
Yellow OPEN Exit button one end(the other end connected GND)
Brown D_IN Magnetic switch one end(the other end connected GND)

Red 12V+ 12V + DC Regulated Power Input

Black GND 12V - DC Regulated Power Input

Blue NO Relay normally-on end(Connect positive electric lock «-»)
Purple COM Relay Public end, connect GND
Orange NC Relay Closed end(connect negative electric lock «-»)

EN

5

GGM AXA1 - Series access control User Manual

EN

Common power supply diagram:

Special power supply diagram:

8. To Reset to Factory Default

a. Disconnect power from the unit
b. Press and hold # key whilst powering the unit back up
c. On hearing two “Di” release # key, system is now back factory settings

Please note only installer data is restored, user data will not be affected

6

GGM AXA1 - Series access control User Manual

9. Anti Tamper Alarm

The unit uses a LDR (light dependent resistor) as an anti tamper alarm.
If the keypad is removed from the cover then the tamper alarm will operate.

10. Sound and Light indication

Operation Status Red Light Green Light Yellow Light Buzzer

Power on - Bright - Di

Stand by Bright - - -

Press keypad - - - Di

Operation successful - Bright - Di

Operation failed - - - DiDiDi

Enter into programming mode Bright - -

In the programming mode - - Bright Di

Exit from the programming mode Bright - - Di

Open the door - Bright - Di

Alarm Bright - - Alarm

11. Detailed Programming Guide

11.1 User Settings

To enter the programming mode

* Master code #

999999 is the default factory master code

To exit from the programming mode

Note that to undertake the following programming the master user must be logged in

To change the master code

0 New code # New code #

The master code can be 6 to 8 digits long

Setting the working mode:

Set valid card only users

3 0 #

Entry is by card only

Set valid card and PIN users

3 1 #

Entry is by card and PIN together

Set valid card or PIN users

3 2 #

Entry is by either card or PIN (default)

To add a user in either card or PIN mode,

i.e. in the

3 2 #

mode. (Default setting)

*

7

EN

GGM AXA1 - Series access control User Manual

EN

To add a Pin user

1 User ID number # PIN #

The ID number is any number between 1 & 2000. The PIN is any four digits between 0000 &
9999 with the exception of 1234 which is reserved. Users can be added continuously without
exiting programming mode as follows:

1 User ID N°1 # PIN # User ID N°2 # PIN #

To delete a PIN user

2 User ID number #

Users can be deleted continuously without exiting programming mode

To change the PIN of a PIN user

(This step must be done out of programming mode)

* ID number # Old PIN # New PIN # New PIN #

To add a card user (Method 1)

This is the fastest way to enter cards, user ID number auto generation.

1 Read card #

Cards can be added continuously without exiting programming mode

To add a card user (Method 2)

This is the alternative way to enter cards using User ID Allocation. In this method a User ID is
allocated to a card. Only one user ID can be allocated to a single card.

1 ID number # Read card #

User can be added continuously without exiting programming mode

To add a card user (Method 3)

Card number is the last 8 digits printed on the back of the card,user ID number auto genera­tion

1 Card number #

User can be added continuously without exiting programming mode

To add a card user (Method 4)

In this method a User ID is allocated to a card number.
Only one user ID can be allocated to the card number

1 ID number.# Card number.#

User can be added continuously without exiting programming mode

To delete a card user by card.

2 Read card #

Note users can be deleted continuously without exiting programming mode

To delete a card user by user ID.

2 Read card #

This option can be used when a user has lost their card

8