GIGABYTE GV-RX26P512H Owner's Manual

GV-RX26P512H

ATI RadeonTM HD 2600 Pro Graphics Accelerator

User's Manual

Rev. 101 12MD-RX26P5H-101R

* The WEEE marking on the product indicates this product must not be disposed of with user's other household waste

and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!

* The WEEE marking applies only in European Union's member states.

without the expressed, written permission of GBT.

Trademarks

Third-party brands and names are the property of their respective owners.

Notice

Please do not remove any labels on VGA card, this may void the warranty of this VGA card

Due to rapid change in technology, some of the specifications might be out of date before publication of this booklet.

The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a

commitment to update the information contained herein.

Macrovision corporation product notice:

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights.

Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing

uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

Table of Contents

English

1. Introduction ......................................................................................... 3

2. Hardware Installation ........................................................................... 4

3. Software Installation .......................................................................... 10

4. Troubleshooting Tips ........................................................................ 32

5. Appendix .......................................................................................... 33

1.1. Features ..................................................................................................... 3

1.2. Minimum System Requirements ................................................................... 3

2.1. Board Layout .............................................................................................. 4

2.2. Hardware Installation ................................................................................... 6

3.1. Windows® XP Driver Installation ................................................................. 10

3.1.1. Operating System Requirement ................................................................................. 10

3.1.2. DirectX Installation ......................................................................................................... 11

3.1.3. Driver Installation .......................................................................................................... 12

3.1.4. Taskbar Icon ................................................................................................................. 14

3.1.5. Display Properties pages ............................................................................................ 15

5.1. How to Reflash the BIOS in MS-DOS mode .............................................. 33

5.2. Resolutions and Color Depth Table (In Windows® XP) ............................... 34

GV-RX26P512H Graphics Accelerator

- 2 -

1. Introduction

1.1. Features

• Powered by ATI RadeonTM HD 2600 Pro Graphics Processing Unit (GPU)

• Supports PCI Express x16

• Integrated with 512 MB GDDR2 memory

• Supports DirectX 9.0c/10

• Supports AV / S-Video / TV-Out and HDTV output

• Supports 2 Dual-Link DVI-I connectors

• Supports D-Sub connector (by adapter)

• Supports HDMI connector (by adapter, optional)

1.2. Minimum System Requirements

• Hardware

- Intel® Pentium® 4 or AMD Athlon

- 512 MB of system memory; 1 GB or more for best performance

- Optical drive for software installation (CD-ROM or DVD-ROM drive)

• Operating System

- Windows® Vista

- Windows® XP with Service Pack 2 (SP2)

- Windows® XP Professional x64 Edition

English

Introduction- 3 -

2.1. Board Layout

English

2. Hardware Installation

DVI-I Connector 1

TV-Out

DVI-I Connector 2

HDTV

NTSC / PAL TV Projector

NTSC / PAL TV

Digital LCD Monitor

Analog LCD Monitor

Analog CRT Monitor

HDMI Monitor

Projector

DVI Output

Pb/AV Output

S-Video Output

DVI-I

Connector 1

TV-Out

DVI-I

Connector 2

D-Sub

Output

DVI-I to D-Sub

Adapter

DVI-I to HDMI Adapter

GV-RX26P512H Graphics Accelerator

- 4 -

Expansion cards contain very delicate Integrated Circuit (IC) chips. To

protect them against damage from static electricity, you should follow some

precautions whenever you work on your computer.

1. Turn off your computer and unplug power supply.

2. Use a grounded wrist strap before handling computer components. If you do not have

one, touch both of your hands to a safely grounded object or to a metal object, such as

the power supply case.

3. Place components on a grounded antistatic pad or on the bag that came with the

components whenever the components are separated from the system.

The card contains sensitive electric components, which can be easily damaged by static

electricity, so the card should be left in its original packing until it is installed.

Unpacking and installation should be done on a grounded anti-static mat. The operator

should be wearing an anti-static wristband, grounded at the same point as the anti-static

mat.

Inspect the card carton for obvious damage. Shipping and handling may cause damage

to your card. Be sure there are no shipping and handling damages on the card before

proceeding.

DO NOT APPLY POWER TO YOUR SYSTEM IF IT HAS BEEN DAMAGED ON

THE CARD.

In order to ensure your graphics card working correctly, please use official

Gigabyte BIOS only. Use none official Gigabyte BIOS might cause problem

on the graphics card.

English

- 5 -

Hardware Installation

2.2. Hardware installation

Installing Your graphics card.

English

Now that you have prepared your computer, you are ready to install your graphics accelerator

card.

To remove the existing graphics card:

1. Power off the computer and monitor, then

2. Remove the computer cover. If necessary,

3. Remove any existing graphics card from

disconnect the display cable from the back

of your computer.

consult your computer's manual for help in

removing the cover.

your computer.

To install your new graphics card:

1. Locate a PCI Express x16 slot. If necessary,

remove the metal cover from the slot; then

align your graphics card with the PCI

Express x16 slot, and press it in firmly until

the card is fully seated.

* Please make sure that the gold edge connector

of the graphics card is securely inserted.

GV-RX26P512H Graphics Accelerator

- 6 -

2. Replace the screw to fasten the card in place,

and replace the computer cover.

3. This graphics card provides two DVI-I digital connectors. You can connect a monitor that supports DVI-I function or use the DVI-I to D-sub adapter to connect a 15-pin D-Sub monitor. Or use the DVI-I to HDMI adapter to connect an HDMI monitor. (Note: Only the DVI-I Connector 2 supports the DVI-I to HDMI adapter.)

English

Connect a flat panel

To TV/VCR

To Flat Panel Display

Connect a D-Sub monitor via DVI-I to D-sub adapter

Connect an HDMI monitor via DVI-I to HDMI adapter

You are now ready to proceed with the installation of the graphics card driver. Please

refer to next chapter for detailed instructions.

- 7 -

Hardware Installation

GIGABYTE Component Video Adapter for ATI Graphics Cards

English

AV Out

S-Video Out

Connect to the TVOut port on the graphics card.

HDTV Component (Y+Pr+Pb)

(1) Connecting HDTV

Connect your HDTV cables to the component video

adapter according to the corresponding color. (Y= Green,

Pr= Red, Pb= Blue)

(2) Connecting S-Video

If your TV has a S-Video connection, connect the S-

Video cable from your TV to the S-Video Out port on the

adapter.

(3) Connecting AV Output

If your TV has Composite video connection, you can

connect the RCA cable from your TV to the AV Out port

on the adapter.

GV-RX26P512H Graphics Accelerator

- 8 -

GIGABYTE Thermal Solution Guidelines:

1. GIGABYTE established the use of silent pipes on graphics card's thermal solution, and has been

the leading company for silent thermal solution. GIGABYTE's passive thermal solution allows system to work perfectly in chassis with 40~50 degrees Celsius through the air flow of the system. Please beware of the other excess component or insufficient system thermal design that may cause high system temperature. Excess high temperature will affect the passive thermal design and thus compromising system stability.

2. GIGABYTE TECHNOLOGY's passive thermal design effectively implemented heat exchange,

radiation and convection to improve stability of the system. Please maintain passive thermal sink at a normal and clean environment. Extra dust on heatsink may decrease the effectiveness of the thermal design.

Silent Thermal Technology Passive Thermal Design

English

- 9 -

Hardware Installation

3. Software Installation

English

In this manual, we assume that your CD-ROM Drive letter to be Drive D:

The installation of Windows® XP drivers is very simple. When you insert the driver CD into

your CD-ROM drive, you can see the AUTORUN window (if it does not show up, run "D:

\setup.exe"). Then you can follow the guides to setup your graphics card driver. (Please

follow the subsection 3.1.3 "Driver Installation" to install the driver for your graphics

accelerator.)

3.1. Windows® XP Driver Installation

3.1.1. Operating System Requirement

• When loading the graphics card drivers for the system, please make sure your system

has installed DirectX 9.0c or later version.

• If you install the graphics card drivers for the motherboard, which consist of SIS, or VIA

chipsets, please install the appropriate driver program for that motherboard. Or please

contact your motherboard nearest dealer for motherboard driver.

GV-RX26P512H Graphics Accelerator

- 10 -

3.1.2. DirectX Installation

Install Microsoft DirectX to enable 3D hardware acceleration support for Windows® XP to

achieve better 3D performance.

0 Note: For software MPEG support in Windows® XP, you must install DirectX first. Users

who run Windows XP with Service Pack 2 or above do not need to install DirectX

separately.

Step 1. When autorun window show up, click the

Install DirectX 9 item.

Click the Install DirectX 9 item.

English

Step 2. Choose I accept the agreement

and click the Next button.

Installing the components.

Step 3. Click the Next button.

Step 4. Click Finish to restart computer.

Then the DirectX 9 installation is completed.

Software Installation- 11 -

+ 23 hidden pages