GIGABYTE GA-MA770-UD3 Owner's Manual

GA-MA770-UD3/ GA-MA770-US3
AM2+/AM2 socket motherboard for AMD PhenomTM II X4 processor/AMD PhenomTM II X3 processor/ AMD PhenomTM FX processor/AMD PhenomTM X4 processor/ AMD PhenomTM X3 processor/AMD AthlonTM X2 processor/ AMD AthlonTM processor/AMD SempronTM X2 processor/ AMD SempronTM processor
User's Manual
Rev. 2002 12ME-MA77UDS3-2002R
Apr. 3, 2009
GA-MA770-UD3/GA-MA770-US3
Motherboard
Apr. 3, 2009
Motherboard
GA-MA770-UD3/
GA-MA770-US3
Copyright
© 2009 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved. The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission.
Documentation Classifications
In order to assist in the use of this product, GIGABYTE provides the following types of documentations:
For quick set-up of the product, read the Quick Installation Guide included with the product.For detailed product information, carefully read the User's Manual.For instructions on how to use GIGABYTE's unique features, read or download the
information on/from the Support\Motherboard\Technology Guide page on our website.
For product-related information, check on our website at: http://www.gigabyte.com.tw
Identifying Your Motherboard Revision
The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0" means the revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information. Example:
Table of Contents
Box Contents ................................................................................................................. 6
Optional Items................................................................................................................. 6
GA-MA770-UD3/US3 Motherboard Layout.................................................................... 7
Block Diagram................................................................................................................ 8
Chapter 1 Hardware Installation .................................................................................... 9
1-1 Installation Precautions .....................................................................................9
1-2 Product Specifications .................................................................................... 10
1-3 Installing the CPU and CPU Cooler.............................................................. 13
1-3-1 Installing the CPU ................................................................................................ 13
1-3-2 Installing the CPU Cooler ................................................................................... 15
1- 4 Installing the Memory ..................................................................................... 16
1-4-1 Dual Channel Memory Configuration ................................................................ 16
1-4-2 Installing a Memory............................................................................................. 17
1- 5 Installing an Expansion Card ......................................................................... 18
1- 6 Back Panel Connectors ................................................................................. 19
1- 7 Internal Connectors ........................................................................................ 21
Chapter 2 BIOS Setup................................................................................................. 33
2-1 Startup Screen................................................................................................ 34
2- 2 The Main Menu .............................................................................................. 35
2- 3 MB Intelligent T weaker(M.I.T.)....................................................................... 37
2- 4 Standard CMOS Features ............................................................................. 42
2-5 Advanced BIOS Features.............................................................................. 44
2-6 Integrated Peripherals ..................................................................................... 46
2- 7 Power Management Setup ............................................................................. 50
2- 8 PC Health Status ........................................................................................... 52
2-9 Load Fail-Safe Defaults................................................................................... 54
2-10 Load Optimized Defaults................................................................................. 54
2-11 Set Supervisor/User Password..................................................................... 55
2-12 Save & Exit Setup......................................................................................... 56
2-13 Exit Without Saving ....................................................................................... 56
- 4 -
Chapter 3 Drivers Installation ...................................................................................... 57
3- 1 Installing Chipset Drivers ............................................................................... 57
3- 2 Application Software ....................................................................................... 58
3- 3 Technical Manuals.......................................................................................... 58
3-4 Contact........................................................................................................... 59
3-5 System........................................................................................................... 59
3- 6 Download Center............................................................................................ 60
Chapter 4 Unique Features......................................................................................... 61
4- 1 Xpress Recovery2 ......................................................................................... 6 1
4-2 BIOS Update Utilities..................................................................................... 64
4-2-1 Updating the BIOS with the Q-Flash Utility ...................................................... 64
4-2-2 Updating the BIOS with the @BIOS Utility ....................................................... 67
4- 3 EasyTune 6.................................................................................................... 6 8
4-4 Easy Energy Saver ...................................................................................... 69
4-5 Q-Share ......................................................................................................... 71
4-6 Time Repair .................................................................................................... 72
Chapter 5 Appendix .................................................................................................... 73
5- 1 Configuring SA TA Hard Drive(s) .................................................................... 73
5-1-1 Configuring the Onboard SATA Controller......................................................... 73
5-1-2 Making a SATA RAID/AHCI Driver Diskette for Windows XP........................ 79
5-1-3 Installing the SATA RAID/AHCI Driver and Operating System ...................... 80
5-2 Configuring Audio Input and Output................................................................. 84
5-2-1 Configuring 2/4/5.1/7.1-Channel Audio ............................................................ 84
5-2-2 Configuring S/PDIF In/Out .................................................................................. 86
5-2-3 Configuring Microphone Recording ................................................................... 88
5-2-4 Using the Sound Recorder ................................................................................. 90
5-3 Troubleshooting ............................................................................................... 91
5-3-1 Frequently Asked Questions ............................................................................. 91
5-3-2 Troubleshooting Procedure ................................................................................ 92
5-4 Regulatory Statements ................................................................................... 94
- 5 -
Box Contents
GA-MA770-UD3 or GA-MA770-US3 motherboard Motherboard driver disk User's Manual Quick Installation Guide One IDE cable Two SAT A 3Gb/s cables I/O Shield
The box contents above are for reference only and the actual items shall depend on product package you obtain. The box contents are subject to change without notice.
The motherboard image is for reference only.
Optional Items
Floppy disk drive cable (Part No. 12CF1-1FD001-7*R) 2-port USB 2.0 bracket (Part No. 12CR1-1UB030-5*R) 2-port IEEE 1394a bracket (Part No. 12CF1-1IE008-0*R) 2-port SATA power cable (Part No. 12CF1-2SERPW -0*R) COM port cable (Part No. 12CF1-1CM001-3*R) S/PDIF in cable (Part No. 12CR1-1SPDIN-0*R) LPT port cable (Part No. 12CF1-1LP001-0*R)
- 6 -
GA-MA770-UD3/US3 Motherboard Layout
KB_MS
SYS_FAN2
RCA_SPDIF
R_USB
USB_1394_1
USB_1394_2
USB_LAN
AUDIO
F_AUDIO
RTL8111C/D(L)
CODEC
SPDIF_OUT
TSB43AB23
F_1394
CD_IN
SPDIF_IN
ATX_12V_2X4
PCIEX1_2
PCIEX1_3
PCIEX1_4
PCI1
PCI2
CPU_FAN
PCIEX1_1
BAT
CLR_CMOS
LPT
Socket AM2
PCIEX16
M_BIOS
B_BIOS
AMD 770
F_USB1
CI
IT8720
FDD
GA-MA770-UD3/US3
AMD SB710
F_USB2
SATA2_1 SATA2_0
SATA2_5 SATA2_4
DDR2_2
DDR2_1
DDR2_3
SATA2_3
SATA2_2
COMA
ATX
PWR_FAN
DDR2_4
IDE
SYS_FAN1
"*" The GA-MA770-UD3 adopts All-Solid Capacitor design.
- 7 -
PWR_LED
F_PANEL
Block Diagram
PCIe CLK (100 MHz)
PCI Express Bus
x1
RTL8111C/D(L)
1 PCI Express x16
PCI Express x16
PCIe CLK (100 MHz)
4 PCI Express x1
PCI Bus
TSB43AB23
x1
x1
RJ45
LAN
x1
AM3/AM2+/AM2
CPU
AMD 770
x1
AMD SB710
CODEC
CPU CLK+/-(200 MHz)
DDR2 1333(O.C.)/1066
Hyper Transport 3.0
IT8720
(Note)
/800 MHz
Dual Channel Memory
ATA-133/100/66/33 IDE Channel
6 SATA 3Gb/s
12 USB Ports
Dual BIOS Floppy
LPT Port
COM Port
3 IEEE 1394a
MIC
Line In
Line Out
S/PDIF In
S/PDIF Out
2 PCI
PCI CLK (33 MHz)
(Note) Whether 1066 MHz or above memory speed is supported depends on the CPU being used.
Side Speaker Out
Surround Speaker Out
Center/Subwoofer Speaker Out
- 8 -
PS/2 KB/Mouse
Chapter 1 Hardware Installation
1-1 Installation Precautions
The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's manual and follow these procedures:
Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or warranty sticker provided by your dealer. These stickers are required for warranty validation.
Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components.
When connecting hardware components to the internal connectors on the motherboard, make sure they are connected tightly and securely.
When handling the motherboard, avoid touching any metal leads or connectors.
It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic
components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap, keep your hands dry and first touch a metal object to eliminate static electricity.
Prior to installing the motherboard, please have it on top of an antistatic pad or within an electrostatic shielding container.
Before unplugging the power supply cable from the motherboard, make sure the power supply has been turned off.
Before turning on the power, make sure the power supply voltage has been set according to the local voltage standard.
Before using the product, please verify that all cables and power connectors of your hardware components are connected.
T o prevent damage to the motherboard, do not allow screws to come in contact with the motherboard circuit or its components.
Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing.
Do not place the computer system on an uneven surface
Do not place the computer system in a high-temperature environment.
Turning on the computer power during the installation process can lead to damage to system
components as well as physical harm to the user.
If you are uncertain about any installation steps or have a problem related to the use of the product, please consult a certified computer technician.
.
Hardware Installation- 9 -
1-2 Product Specifications
CPU Support for AM3/AM2+/AM2 processors
AMD PhenomTM II X4 processor/AMD PhenomTM II X3 processor/ AMD PhenomTM FX processor/AMD PhenomTM X4 processor/ AMD PhenomTM X3 processor/AMD AthlonTM X2 processor/ AMD AthlonTM processor/AMD Sempron AMD Sempron
TM
processor
(Go to GIGABYTE's website for the latest CPU support list.) Hyper Transport Bus 5200/2000 MT/s Chipset North Bridge: AMD 770
South Bridge: AMD SB710
Memory 4 x 1.8V DDR2 DIMM sockets supporting up to 16 GB of system memory
Dual channel memory architectureSupport for DDR2 1333(O.C.)/1066
(Go to GIGABYTE's website for the latest memory support list.)
Support for ECC memory
(Note 4)
Audio Realtek ALC888 codec
High Definition Audio2/4/5.1/7.1-channelSupport for S/PDIF In/OutSupport for CD In
LAN RTL8111C/D(L) chip (10/100/1000 Mbit) Expansion Slots 1 x PCI Express x16 slot, running at x16
(The PCI Express x16 slot conforms to PCI Express 2.0 standard.)
4 x PCI Express x1 slots2 x PCI slots
Storage Interface South Bridge:
- 1 x IDE connector supporting ATA-133/100/66/33 and up to 2 IDE devices
- 6 x SATA 3Gb/s connectors supporting up to 6 SATA 3Gb/s devices
- Support for SATA RAID 0, RAID 1, RAID 10, and JBOD
iTE IT8720 chip:
- 1 x floppy disk drive connector supporting up to 1 floppy disk drive
IEEE 1394 T.I. TSB43AB23 chip
Up to 3 IEEE 1394a ports (2 on the back panel, 1 via the IEEE 1394a bracket
connected to the internal IEEE 1394a header) USB Integrated in the South Bridge
Up to 12 USB 2.0/1.1 ports (8 on the back panel, 4 via the USB brackets
connected to the internal USB headers)
(Note 1)
:
TM
X2 processor/
(Note 3)
/800 MHz memory modules
(Note 2)
"*" The GA-MA770-UD3 adopts All-Solid Capacitor design. GA-MA770-UD3/US3 Motherboard - 10 -
Internal Connectors 1 x 24-pin ATX main power connector
1 x 8-pin ATX 12V power connector1 x floppy disk drive connector1 x IDE connector6 x SATA 3Gb/s connectors1 x CPU fan header2 x system fan headers1 x power fan header1 x front panel header1 x front panel audio header1 x CD In connector1 x S/PDIF In header1 x S/PDIF Out header2 x USB 2.0/1.1 headers1 x IEEE 1394a header1 x parallel port header1 x serial port header1 x power LED header1 x chassis intrusion header
Back Panel 1 x PS/2 keyboard port Connectors 1 x PS/2 mouse port
1 x coaxial S/PDIF Out connector1 x optical S/PDIF Out connector8 x USB 2.0/1.1 ports2 x IEEE 1394a ports1 x RJ-45 port6 x audio jacks (Center/Subwoofer Speaker Out/Rear Speaker Out/Side
Speaker Out/Line In/Line Out/Microphone) I/O Controller iTE IT8720 chip Hardware Monitor System voltage detection
CPU/System temperature detectionCPU/System/Power fan speed detectionCPU overheating warningCPU/System/Power fan fail warningCPU/System fan speed control
(Note 5)
BIOS 2 x 8 Mbit flash
Use of licensed AWARD BIOSSupport for DualBIOS
TM
PnP 1.0a, DMI 2.0, SM BIOS 2.4, ACPI 1.0b
Hardware Installation- 11 -
Unique Features Support for @BIOS
Support for Q-FlashSupport for Xpress BIOS RescueSupport for Download CenterSupport for Xpress InstallSupport for Xpress Recovery2Support for EasyTuneSupport for Easy Energy Saver
(Note 6)
(Note 7)
Support for Time RepairSupport for Q-Share
Bundled Software Norton Internet Security (OEM version) Operating System Support for Microsoft® Windows® Vista/XP Form Factor ATX Form Factor; 30.5cm x 21.0cm
(Note 1) We recommend that you enhance heat dissipation for the CPU VRM area if an AMD Black
Edition CPU is installed and Advanced Clock Calibration is enabled.
(Note 2) Due to Windows Vista/XP 32-bit operating system limitation, when more than 4 GB of physical
memory is installed, the actual memory size displayed will be less than 4 GB. (Note 3) Whether 1066 MHz or above memory speed is supported depends on the CPU being used. (Note 4) Use of a CPU that supports ECC is required if you wish to install ECC memory. (Note 5) Whether the CPU/system fan speed control function is supported will depend on the CPU/
system cooler you install. (Note 6) Available functions in EasyTune may differ by motherboard model. (Note 7) Due to the hardware limitation, you must install the AMD AM3 Phenom
TM
II/AM2+ Phenom
TM
Series CPU toenable support for Easy Energy Saver. GA-MA770-UD3/US3 Motherboard - 12 -
1-3 Installing the CPU and CPU Cooler
Read the following guidelines before you begin to install the CPU:
Make sure that the motherboard supports the CPU. (Go to GIGABYTE's website for the latest CPU support list.)
Always turn off the computer and unplug the power cord from the power outlet before installing the CPU to prevent hardware damage.
Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly.
Apply an even and thin layer of thermal grease on the surface of the CPU.
Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and
damage of the CPU may occur.
Set the CPU host frequency in accordance with the CPU specifications. It is not recom­mended that the system bus frequency be set beyond hardware specifications since it does not meet the standard requirements for the peripherals. If you wish to set the frequency beyond the standard specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc.
1-3-1 Installing the CPU
A. Locate the pin one (denoted by a small triangle) of the CPU socket and the CPU.
A Small Triangle Mark Denotes Pin One of the Socket
A Small Triangle Marking Denotes CPU Pin One
AM2 Socket
AM3/AM2+/AM2 CPU
Hardware Installation- 13 -
B. Follow the steps below to correctly install the CPU into the motherboard CPU socket.
Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the CPU.
CPU Socket Locking Lever
Step 1: Completely lift up the CPU socket locking lever.
Step 2: Align the CPU pin one (small triangle marking) with the triangle mark on the CPU socket and gently insert the CPU into the socket. Make sure that the CPU pins fit perfectly into their holes. Once the CPU is positioned into its socket, place one finger down on the middle of the CPU, lowering the locking lever and latch­ing it into the fully locked position.
Do not force the CPU into the CPU socket. The CPU cannot fit in if oriented incorrectly. Adjust the CPU orientation if this occurs.
GA-MA770-UD3/US3 Motherboard - 14 -
1-3-2 Installing the CPU Cooler
Follow the steps below to correctly install the CPU cooler on the CPU. (The following procedure uses the GIGABYTE cooler as the example.)
Step 1: Apply an even and thin layer of thermal grease on the surface of the installed CPU.
Step 3: Hook the CPU cooler clip to the mounting lug on one side of the retention frame. On the other side, push straight down on the the CPU cooler clip to hook it to the mounting lug on the retention frame.
Step 5: Finally, attach the power connector of the CPU cooler to the CPU fan header (CPU_FAN) on the motherboard.
Step 2: Place the CPU cooler on the CPU.
Step 4: Turn the cam handle from the left side to the right side (as the picture above shows) to lock into place. (Refer to your CPU cooler installa­tion manual for instructions on installing the cooler.)
Use extreme care when removing the CPU cooler because the thermal grease/tape between the CPU cooler and CPU may adhere to the CPU. Inadequately removing the CPU cooler may damage the CPU.
Hardware Installation- 15 -
1-4 Installing the Memory
Read the following guidelines before you begin to install the memory:
Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used. (Go to GIGABYTE's website for the latest memory support list.)
Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage.
Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction.
1-4-1 Dual Channel Memory Configuration
This motherboard provides four DDR2 memory sockets and supports Dual Channel Technology. After the memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual Channel memory mode will double the original memory bandwidth.
The four DDR2 memory sockets are divided into two channels and each channel has two memory sockets as following:
Channel 0: DDR2_1, DDR2_3 Channel 1: DDR2_2, DDR2_4
Dual Channel Memory Configurations T able
Two Modules
Four Modules
(SS=Single-Sided, DS=Double-Sided, "- -"=No Memory)
DDR2_1 DDR2_2 DDR2_3 DDR2_4 DS/SS DS/SS - - - -
- - - - DS/SS DS/SS DS/SS DS/SS DS/SS DS/SS
If two memory modules are to be installed, it is recom­mended that you install them in the DDR2_1 and DDR2_2 sockets.
DDR2_3
DDR2_1
DDR2_2
DDR2_4
Due to CPU limitation, read the following guidelines before installing the memory in Dual Channel mode.
1. Dual Channel mode cannot be enabled if only one DDR2 memory module is installed.
2. When enabling Dual Channel mode with two or four memory modules, it is recommended that memory of the same capacity, brand, speed, and chips be used and installed in the same colored DDR2 sockets for optimum performance.
GA-MA770-UD3/US3 Motherboard - 16 -
1-4-2 Installing a Memory
Before installing a memory module , make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the memory module. DDR2 DIMMs are not compatible to DDR DIMMs. Be sure to install DDR2 DIMMs on this motherboard.
Notch
DDR2 DIMM
A DDR2 memory module has a notch, so it can only fit in one direction. Follow the steps below to correctly install your memory modules in the memory sockets.
Step 1: Note the orientation of the memory module. Spread the retaining clips at both ends of the memory socket. Place the memory module on the socket. As indicated in the picture on the left, place your fingers on the top edge of the memory, push down on the memory and insert it vertically into the memory socket.
Step 2: The clips at both ends of the socket will snap into place when the memory module is securely inserted.
Hardware Installation- 17 -
1-5 Installing an Expansion Card
Read the following guidelines before you begin to install an expansion card:
Make sure the motherboard supports the expansion card. Carefully read the manual that came with your expansion card.
Always turn off the computer and unplug the power cord from the power outlet before installing an expansion card to prevent hardware damage.
PCI Express x1 Slot
PCI Express x16 Slot
PCI Slot
Follow the steps below to correctly install your expansion card in the expansion slot.
1. Locate an expansion slot that supports your card. Remove the metal slot cover from the chassis back panel.
2. Align the card with the slot, and press down on the card until it is fully seated in the slot.
3. Make sure the metal contacts on the card are completely inserted into the slot.
4. Secure the card's metal bracket to the chassis back panel with a screw.
5. After installing all expansion cards, replace the chassis cover(s).
6. Turn on your computer. If necessary, go to BIOS Setup to make any required BIOS changes for your expansion card(s).
7. Install the driver provided with the expansion card in your operating system.
Example: Installing and Removing a PCI Express x16 Graphics Card:
Installing a Graphics Card: Gently push down on the top edge of the card until it is fully inserted into the PCI Express x16 slot. Make sure the card is securely seated in the slot and does not rock.
Removing the Card: Gently push back on the lever on the slot and then lift the card straight out from the slot.
GA-MA770-UD3/US3 Motherboard - 18 -
1-6 Back Panel Connectors
PS/2 Keyboard and PS/2 Mouse Port
Use the upper port (green) to connect a PS/2 mouse and the lower port (purple) to connect a PS/2 keyboard.
Optical S/PDIF Out Connector
This connector provides digital audio out to an external audio system that supports digital optical audio. Before using this feature, ensure that your audio system provides an optical digital audio in connector.
Coaxial S/PDIF Out Connector
This connector provides digital audio out to an external audio system that supports digital coaxial audio. Before using this feature, ensure that your audio system provides a coaxial digital audio in connector.
USB Port
The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc.
IEEE 1394a Port
The IEEE 1394 port supports the IEEE 1394a specification, featuring high speed, high bandwidth and hotplug capabilities. Use this port for an IEEE 1394a device.
RJ-45 LAN Port
The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following describes the states of the LAN port LEDs.
Connection/ Speed LED
LAN Port
Activity LED
Connection/Speed LED:
State Description Orange 1 Gbps data rate Green 100 Mbps data rate Off 10 Mbps data rate
Activity LED:
State Description Blinking Data transmission or receiving is occurring Off No data transmission or receiving is occurring
When removing the cable connected to a back panel connector, first remove the cable from your device and then remove it from the motherboard.
When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector.
Hardware Installation- 19 -
Center/Subwoofer Speaker Out Jack (Orange)
Use this audio jack to connect center/subwoofer speakers in a 5.1/7.1-channel audio configuration.
Rear Speaker Out Jack (Black)
Use this audio jack to connect rear speakers in a 4/5.1/7.1-channel audio configuration.
Side Speaker Out Jack (Gray)
Use this audio jack to connect side speakers in a 7.1-channel audio configuration.
Line In Jack (Blue)
The default line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.
Line Out Jack (Green)
The default line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be used to connect front speakers in a 4/5.1/7.1-channel audio configuration.
Mic In Jack (Pink)
The default Mic in jack. Microphones must be connected to this jack.
In addition to the default speakers settings, the ~ audio jacks can be reconfigured to perform different functions via the audio software. Only microphones still MUST be connected to the default Mic in jack ( ). Refer to the instructions on setting up a 2/4/5.1/
7.1-channel audio configuration in Chapter 5, "Configuring 2/4/5.1/7.1-Channel Audio."
GA-MA770-UD3/US3 Motherboard - 20 -
1-7 Internal Connectors
4
3
2
1
12
10 14
13 15
21
17
1) ATX_12V_2X4
2) AT X
3) CPU_FAN
4) SYS_FAN1/SYS_FAN2
5) PWR_FAN
6) FDD
7) IDE
8) SATA2_0/1/2/3/4/5
9) PWR_LED
10) B AT
11) F_PANEL
5
16
7
8 4
19
6
9
18
20
11
12) F_AUDIO
13) CD_IN
14) SPDIF_IN
15) SPDIF_OUT
16) F_USB1/F_USB2
17) F_1394
18) L PT
19) COMA
20) CI
21) CLR_CMOS
Read the following guidelines before connecting external devices:
First make sure your devices are compliant with the connectors you wish to connect.
Before installing the devices, be sure to turn off the devices and your computer. Unplug the
power cord from the power outlet to prevent damage to the devices.
After installing the device and before turning on the computer, make sure the device cable has been securely attached to the connector on the motherboard.
Hardware Installation- 21 -
1/2) ATX_12V_2X4/ATX (2x4 12V Power Connector and 2x12 Main Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, first make sure the power supply is turned off and all devices are properly installed. The power connector possesses a foolproof design. Connect the power supply cable to the power connector in the correct orientation. The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected, the computer will not start.
To meet expansion requirements, it is recommended that a power supply that can withstand high power consumption be used (500W or greater). If a power supply is used that does not provide the required power, the result can lead to an unstable or unbootable system.
The power connectors are compatible with power supplies with 2x2 12V and 2x10 power connectors. When using a power supply providing a 2x4 12V and a 2x12 power connector, remove the protective covers from the 12V power connector and the main power connector on the motherboard. Do not insert the power supply cables into pins under the protective covers when using a power supply providing a 2x2 12V and a 2x10 power connector.
ATX_12V_2X4:
8
5
ATX_12V_2X4
4
1
Pin No. Definition
1 GND (Only for 2x4 pin 12V) 2 GND (Only for 2x4 pin 12V) 3 GND 4 GND 5 +12V (Only for 2x4 pin 12V) 6 +12V (Only for 2x4 pin 12V) 7 +12V 8 +12V
ATX:
13 1
24 12
ATX
Pin No. Definition
1 3.3V 2 3.3V 3 GND 4 +5V 5 GND 6 +5V 7 GND 8 Power Good 9 5V SB(stand by +5V) 10 +12V 11 +12V (Only for 2x12-pin A TX) 12 3.3V (Only for 2x12-pin ATX)
GA-MA770-UD3/US3 Motherboard - 22 -
Pin No. Definition
13 3.3V 14 -12V 15 GND 16 PS_ON(soft On/Off) 17 GND 18 GND 19 GND 20 -5V 21 +5V 22 +5V 23 +5V (Only for 2x12-pin ATX) 24 GND (Only for 2x12-pin ATX)
3/4/5) CPU_FAN/SYS_F AN1/SYS_F AN2/PWR_FAN (Fan Headers)
The motherboard has a 4-pin CPU fan header (CPU_FAN), a 3-pin (SYS_FAN2) and a 4-pin (SYS_FAN1) system fan headers, and a 3-pin power fan header (PWR_FAN). Most fan headers possess a foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire). The motherboard supports CPU fan speed control, which requires the use of a CPU fan with fan speed control design. For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.
CPU_FAN:
Pin No. Definition
1
CPU_FAN
1
SYS_FAN1
1
SYS_FAN2
1 PWR_FAN
Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating. Overheating may result in damage to the CPU or the system may hang.
These fan headers are not configuration jumper blocks. Do not place a jumper cap on the headers.
1 GND 2 +12V / Speed Control 3 Sense 4 Speed Control
SYS_FAN1:
Pin No. Definition
1 GND 2 +12V / Speed Control 3 Sense 4 Reserve
SYS_FAN2/PWR_FAN:
Pin No. Definition
1 GND 2 +12V 3 Sense
6) FDD (Floppy Disk Drive Connector)
This connector is used to connect a floppy disk drive. The types of floppy disk drives supported are: 360 KB, 720 KB, 1.2 MB, 1.44 MB, and 2.88 MB. Before connecting a floppy disk drive, be sure to locate pin 1 of the connector and the floppy disk drive cable. The pin 1 of the cable is typically designated by a stripe of different color.
33
34
1
2
Hardware Installation- 23 -
7) IDE (IDE Connector)
The IDE connector supports up to two IDE devices such as hard drives and optical drives. Before attaching the IDE cable, locate the foolproof groove on the connector. If you wish to connect two IDE devices, remember to set the jumpers and the cabling according to the role of the IDE devices (for example, master or slave). (For information about configuring master/slave settings for the IDE devices, read the instructions from the device manufacturers.)
40
39
2
1
8) SATA2_0/1/2/3/4/5 (SATA 3Gb/s Connectors)
The SATA connectors conform to SATA 3Gb/s standard and are compatible with SATA 1.5Gb/s standard. Each SATA connector supports a single SATA device. The AMD SB710 controller supports RAID 0, RAID 1, RAID 10, and JBOD. Refer to Chapter 5, "Configuring SATA Hard Drive (s)," for instructions on configuring a RAID array.
Pin No. Definition
1 GND
17
17
7
7
2 TXP 3 TXN 4 GND 5 RXN 6 RXP 7 GND
1
SATA2_1
SATA2_0
SATA2_3
17
7
1
SATA2_2
SATA2_5
1
SATA2_4
A RAID 0 or RAID 1 configuration requires at least two hard drives. If more than two hard drives are to be used, the total number of hard drives must be an even number.
A RAID 10 configuration requires at least four hard drives and the total number of hard drives must be an even number.
GA-MA770-UD3/US3 Motherboard - 24 -
Please connect the L-shaped end of the SATA 3Gb/s cable to your SATA hard drive.
9) PWR_LED (System Power LED Header)
This header can be used to connect a system power LED on the chassis to indicate system power status. The LED is on when the system is operating. The LED keeps blinking when the system is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5).
Pin No. Definition
1 MPD+ 2 MPD-
1
3 MPD-
System Status LED S0 On S1 Blinking S3/S4/S5 Off
10) BAT (BATTERY)
The battery provides power to keep the values (such as BIOS configurations, date, and time information) in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low level, or the CMOS values may not be accurate or may be lost.
You may clear the CMOS values by removing the battery:
1. Turn off your computer and unplug the power cord.
2. Gently remove the battery from the battery holder and wait for one minute. (Or use a metal object like a screwdriver to touch the positive and negative terminals of the battery holder, making them short for 5 seconds.)
3. Replace the battery.
4. Plug in the power cord and restart your computer.
Always turn off your computer and unplug the power cord before replacing the battery.
Replace the battery with an equivalent one. Danger of explosion if the battery is replaced
with an incorrect model.
Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or uncertain about the battery model.
When installing the battery, note the orientation of the positive side (+) and the negative side (-) of the battery (the positive side should face up).
Used batteries must be handled in accordance with local environmental regulations.
Hardware Installation- 25 -
11) F_PANEL (Front Panel Header)
Connect the power switch, reset switch, speaker and system status indicator on the chassis front panel to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.
Message/Power/
Activity LED
Sleep LED
2 1
Hard Drive
MSG+
HD+
MSG-
HD-
Power Switch
PW+
RES-
Reset Switch
PW-
RES+
Speaker
SPEAK-
SPEAK+
20 19
NC
MSG (Message/Power/Sleep LED, Yellow):
System Status LE D S0 On S1 Blinking S3/S4/S5 Off
Connects to the power status indicator o n the chassis front panel. The LED is on when the system is operating. The LED keeps blinking when the system is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5).
PW (Power Switch, Red): Connects to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch (refer to Chapter 2, "BIOS Setup," "Power Management Setup," for more information).
SPEAK (Speaker, Orange): Connects to the speaker on the chassis front panel. The system reports system startup status by issuing a beep code. One single short beep will be heard if no problem is detected at system startup. If a problem is detected, the BIOS may issue beeps in different patterns to indicate the problem. Refer to Chapter 5, "Troubleshooting," for information about beep codes.
HD (Hard Drive Activity LED, Blue) Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data.
RES (Reset Switch, Green): Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart.
NC (Purple): No connection
The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assign­ments and the pin assignments are matched correctly.
GA-MA770-UD3/US3 Motherboard - 26 -
12) F_AUDIO (Front Panel Audio Header)
The front panel audio header supports Intel High Definition audio (HD) and AC'97 audio. You may connect your chassis front panel audio module to this header. Make sure the wire assignments of the module connector match the pin assignments of the motherboard header. Incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it.
For HD Front Panel Audio:
Pin No. Definition
9
10
21
1 MIC2_L 2 GND 3 MIC2_R 4 -ACZ_DET 5 LINE2_R 6 GND 7 FAUDIO_JD 8 No Pin 9 LINE2_L 10 GND
The front panel audio header supports HD audio by default. If your chassis provides an AC'97 front panel audio module, refer to the instructions on how to activate AC'97 functionality via the audio software in Chapter 5, "Configuring 2/4/5.1/7.1-Channel Audio."
Audio signals will be present on both of the front and back panel audio connections simultaneously. If you want to mute the back panel audio (only supported when using an HD front panel audio module), refer to Chapter 5, "Configuring 2/4/5.1/7.1-Channel Audio."
Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug. For information about connecting the front panel audio module that has different wire assignments, please contact the chassis manufacturer.
13) CD_IN (CD In Connector, Black)
You may connect the audio cable that came with your optical drive to the header.
For AC'97 Front Panel Audio:
Pin No. Definition
1 MIC 2 GND 3 MIC Power 4NC 5 Line Out (R) 6NC 7NC 8 No Pin 9 Line Out (L) 10 NC
Pin No. Definition
1 CD-L 2 GND
1
3 GND 4 CD-R
Hardware Installation- 27 -
14) SPDIF_IN (S/PDIF In Header, Red)
This header supports digital S/PDIF In and can connect to an audio device that supports digital audio out via an optional S/PDIF In cable. For purchasing the optional S/PDIF In cable, please contact the local dealer.
Pin No. Definition
1 Power
1
2 SPDIFI 3 GND
15) SPDIF_OUT (S/PDIF Out Header)
This header supports digital S/PDIF Out and connects a S/PDIF digital audio cable (provided by expansion cards) for digital audio output from your motherboard to certain expansion cards like graphics cards and sound cards. For example, some graphics cards may require you to use a S/PDIF digital audio cable for digital audio output from your motherboard to your graphics card if you wish to connect an HDMI display to the graphics card and have digital audio output from the HDMI display at the same time. For information about connecting the S/PDIF digital audio cable, carefully read the manual for your expansion card.
GA-MA770-UD3/US3 Motherboard - 28 -
Pin No. Definition
1
1 SPDIFO 2 GND
16) F_USB1/F_USB2 (USB Headers, Yellow)
The headers conform to USB 2.0/1.1 specification. Each USB header can provide two USB ports via an optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.
Pin No. Definition
1 Power (5V) 2 Power (5V)
10 9
21
3 USB DX­4 USB DY ­5 USB DX+ 6 USB DY+ 7 GND 8 GND 9 No Pin 10 NC
Do not plug the IEEE 1394 bracket (2x5-pin) cable into the USB header.
Prior to installing the USB bracket, be sure to turn off your computer and unplug the
power cord from the power outlet to prevent damage to the USB bracket.
17 ) F_1394 (IEEE 1394a Header, Gray)
The header conforms to IEEE 1394a specification. The IEEE 1394a header can provide one IEEE 1394a port via an optional IEEE 1394a bracket. For purchasing the optional IEEE 1394a bracket, please contact the local dealer.
Pin No. Definition
1TPA+ 2TPA-
10
2
9
1
3 GND 4 GND 5 TPB+ 6 TPB­7 Power (12V) 8 Power (12V) 9 No Pin 10 GND
Do not plug the USB bracket cable into the IEEE 1394a header.
Prior to installing the IEEE 1394a bracket, be sure to turn off your computer and unplug
the power cord from the power outlet to prevent damage to the IEEE 1394a bracket.
To connect an IEEE 1394a device, attach one end of the device cable to your computer and then attach the other end of the cable to the IEEE 1394a device. Ensure that the cable is securely connected.
Hardware Installation- 29 -
18) LPT (Parallel Port Header)
The LPT header can provide one parallel port via an optional LPT port cable. For purchasing the optional LPT port cable, please contact the local dealer.
2
26
1
Pin No. Definition
1 STB­2 AFD­3 PD0 4 ERR­5 PD1 6 INIT­7 PD2 8 SLIN­9 PD3 10 GND 1 1 PD4 12 GND 13 PD5
25
Pin No. Definition
14 GND 15 PD6 16 GND 17 PD7 18 GND 19 ACK­20 GND 21 BUSY 22 GND 23 PE 24 No Pin 25 SLCT 26 GND
19) COMA (Serial Port Header)
The COM header can provide one serial port via an optional COM port cable. For purchasing the optional COM port cable, please contact the local dealer.
Pin No. Definition
1 NDCD­2 NSIN 3 NSOUT
10
21
9
4 NDTR­5 GND 6 NDSR­7 NRTS­8 NCTS­9 NRI­10 No Pin
GA-MA770-UD3/US3 Motherboard - 30 -
Loading...
+ 70 hidden pages