Gigabyte GA-965P-DS3P User Manual

0 (0)

GA-965P-DS3P

Intel® Core Intel® Core

2 Extreme quad-core / Core

2 Extreme dual-core / Core Intel® Pentium® Processor Extreme Edition / Intel® Pentium® D / Pentium® 4 LGA775 Processor Motherboard

User's Manual

Rev. 3301

12ME-965PDS3P-3301R

2 Quad /

2 Duo /

* The WEEE marking on the product indicates this product must not be disposed of with user's other household waste

and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!

* The WEEE marking applies only in European Union's member states.

Nov. 10, 2006

GA-965P-DS3P

Motherboard

Nov. 10, 2006

Motherboard

GA-965P-DS3P

The trademarks mentioned in the manual are legally registered to their respective companies.

Notice

The written content provided with this product is the property of Gigabyte.

No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any

means without Gigabyte's prior written permission. Specifications and features are subject to

change without prior notice.

Product Manual Classification

In order to assist in the use of this product, Gigabyte has categorized the user manual in the

following:

 For quick installation, please refer to the "Hardware Installation Guide" included with the

product.

 For detailed product information and specifications, please carefully read the

"Product User Manual".

 For detailed information related to Gigabyte's unique features, please go to "Technology

Guide" section on Gigabyte's website to read or download the information you need.

For more product details, please click onto Gigabyte's website at www.gigabyte.com.tw

Table of Contents

Item Checklist ................................................................................................................. 6

Optional Accessories ...................................................................................................... 6

GA-965P-DS3P Motherboard Layout ............................................................................ 7

Block Diagram ................................................................................................................ 8

Chapter 1 Hardware Installation ..................................................................................... 9

1-1 Considerations Prior to Installation .................................................................... 9

1-2 Feature Summary .......................................................................................... 10

1-3 Installation of the CPU and CPU Cooler ....................................................... 13

1-3-1 Installation of the CPU ......................................................................................... 13

1-3-2 Installation of the CPU Cooler ............................................................................ 14

1-4 Installation of Memory .................................................................................... 15

1-5 Installation of Expansion Cards ...................................................................... 17

1-6 I/O Back Panel Introduction ........................................................................... 18

1-7 Connectors Introduction .................................................................................. 19

Chapter 2 BIOS Setup ................................................................................................ 31

The Main Menu (For example: BIOS Ver. : F4a) ...................................................... 32

2-1 Standard CMOS Features ............................................................................. 34

2-2 Advanced BIOS Features.............................................................................. 36

2-3 Integrated Peripherals ..................................................................................... 38

2-4 Power Management Setup ............................................................................. 41

2-5 PnP/PCI Configurations................................................................................. 42

2-6 PC Health Status ........................................................................................... 43

2-7 MB Intelligent Tweaker(M.I.T.) ....................................................................... 45

2-8 Load Fail-Safe Defaults ................................................................................... 48

2-9 Load Optimized Defaults ................................................................................. 48

2-10 Set Supervisor/User Password ..................................................................... 49

2-11 Save & Exit Setup......................................................................................... 50

2-12 Exit Without Saving ....................................................................................... 50

- 4 -

Chapter 3 Drivers Installation ...................................................................................... 51

3-1 Install Chipset Drivers .................................................................................... 51

3-2 Software Applications ..................................................................................... 52

3-3 Driver CD Information .................................................................................... 52

3-4 Hardware Information ..................................................................................... 53

3-5 Contact Us ..................................................................................................... 53

Chapter 4 Appendix ................................................................................................... 55

4-1 Unique Software Utilities ................................................................................ 55

4-1-1 EasyTune 5 Introduction ..................................................................................... 55

4-1-2 Xpress Recovery2 Introduction ......................................................................... 56

4-1-3 Flash BIOS Method Introduction ........................................................................ 58

4-1-4 Configuring SATA Hard Drive(s) ........................................................................ 65

A. Intel® ICH8R Southbridge ............................................................................... 65

B. GIGABYTE SATA2 Controller ........................................................................ 76

4-1-5 2- / 4- / 6- / 8- Channel Audio Function Introduction ...................................... 88

4-2 Troubleshooting ............................................................................................... 93

- 5 -

Item Checklist

IDE Cable x 1, FDD Cable x 1

SATA 3Gb/s Cable x 4

I/O Shield

* The items listed above are for reference only, and are subject to change without notice.

Optional Accessories

 2 Ports USB 2.0 Cable (Part Number: 12CR1-1UB030-51/R)

 4 Ports USB 2.0 Cable (Part Number: 12CR1-1UB030-21/R)

 2 Ports IEEE 1394 Cable (Part Number: 12CF1-1IE008-01R)

 2 Ports SATA Power Cable (Part Number: 12CF1-2SERPW-01R)

 S/PDIF-IN Cable (Part Number: 12CR1-1SPDIN-01R)

 e-SATA Cable (Part Number: 12CF1-3SATPW-11R)

- 6 -

GA-965P-DS3P Motherboard Layout

COAXIAL

OPTICAL

KB_MS

COM

USB

AUDIO

Marvell 8053

CODEC

LPT

ATX_12V_2X

1394

LAN

CD_IN

IT8718

BATTERY

CLR_CMOS

F_AUDIO

PCI1

PCI2

SPDIF_IN

PCIE_16_1

PCIE_2

PCIE_3

PCIE_16_2

CPU_FAN

PCIE_1

NB_FAN

BACKUP BIOS

SYS_FAN

LGA775

Intel® P965

MAIN BIOS

F1_1394

TSB43AB23

PWR_FAN

GA-965P-DS3P

DDRII2

DDRII1

Intel® ICH8R

SATAII4

SATAII5

GSATAII1

F_USB1

F_USB2

F_USB3

PWR_LED

SATAII0

SATAII1

SATAII2

SATAII3

GIGABYTE SATA2

F_PANEL

PCIE_12V

DDRII4

DDRII3

GSATAII0

ATX

FDD

IDE

- 7 -

F2_1394

Block Diagram

3 PCI Express x1

PCI Express x1

PCIe CLK

PCI Express x3

(100 MHz)

x1 x1

Switch

PCI Express Bus

2 SATA 3Gb/s

ATA-33/66/100/

133 IDE Channel

PCI Bus

TSB43AB23

PCIe CLK

(100 MHz)

PCI Express x16

LAN

RJ45

Marvell

8056

GIGABYTE

SATA2

LGA775

Processor

Intel P965

Intel

ICH8R

CODEC

Host

Interface

CPU CLK+/-(333

(Note 1)

/266/200/133 MHz)

DDRII 800/667/533 MHz DIMM

Dual Channel Memory

MCH CLK (266/200/133 MHz)

Dual BIOS

6 SATA 3Gb/s

10 USB Ports

IT8718

(Note 2)

Floppy

LPT Port

COM Port

3 IEEE 1394a

2 PCI

MIC

Line-Out

Line-In

SPDIF In

PS/2 KB/Mouse

SPDIF Out

Side Speaker Out

Surround Speaker Out

PCI CLK

(33 MHz)

Center/Subwoofer Speaker Out

(Note 1) Applies only when the GA-965P-DS3P motherboard (rev. 3.3) is installed with a 1333 MHz

FSB processor. The system will automatically adjust BIOS to support 1333 MHz FSB by overclocking when a 1333 MHz FSB processor is installed. In such a configuration, the actual operating memory frequency will be 667 MHz or 833 MHz, depending on the memory being installed.

(Note 2) To use a DDR II 800/667 memory module on the motherboard, you must install a 1333/1066/

800 MHz FSB processor.

- 8 -

Chapter 1 Hardware Installation

1-1 Considerations Prior to Installation

Preparing Your Computer

The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please follow the instructions below:

1. Please turn off the computer and unplug its power cord.

2. When handling the motherboard, avoid touching any metal leads or connectors.

3. It is best to wear an electrostatic discharge (ESD) cuff when handling electronic components

(CPU, RAM).

4. Prior to installing the electronic components, please have these items on top of an antistatic pad or

within a electrostatic shielding container.

5. Please verify that the power supply is switched off before unplugging the power supply connector

from the motherboard.

Installation Notices

1. Prior to installation, please do not remove the stickers on the motherboard. These stickers are required

for warranty validation.

2. Prior to the installation of the motherboard or any hardware, please first carefully read the information

in the provided manual.

3. Before using the product, please verify that all cables and power connectors are connected.

4. To prevent damage to the motherboard, please do not allow screws to come in contact with the

motherboard circuit or its components.

5. Please make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

6. Please do not place the computer system on an uneven surface.

7. Turning on the computer power during the installation process can lead to damage to system

components as well as physical harm to the user.

8. If you are uncertain about any installation steps or have a problem related to the use of the product,

please consult a certified computer technician.

English

Instances of Non-Warranty

1. Damage due to natural disaster, accident or human cause.

2. Damage as a result of violating the conditions recommended in the user manual.

3. Damage due to improper installation.

4. Damage due to use of uncertified components.

5. Damage due to use exceeding the permitted parameters.

6. Product determined to be an unofficial Gigabyte product.

Hardware Installation- 9 -

English

1-2 Feature Summary

CPU  LGA775 for Intel® Core

2 Extreme quad-core / Core CoreTM 2 Quad / CoreTM 2 Duo / Pentium® processor Extreme Edition / Pentium® D / Pentium® 4 / Celeron® D

 L2 cache varies with CPU

Front Side Bus  Supports 1333

(Note 1)

/1066/800/533 MHz FSB

Chipset  Northbridge: Intel® P965 Express Chipset

 Southbridge: Intel® ICH8R LAN  Onboard Marvell 8056 chip (10/100/1000 Mbit) Audio  Onboard Realtek ALC888 chip

 Supports High Definition Audio

 Supports 2 / 4 / 6 / 8 channel audio

 Supports S/PDIF In/Out connection

 Supports CD In connection IEEE 1394  Onboard T.I. TSB43AB23 chip

 3 IEEE 1394a ports

Storage  ICH8R Southbrigde

- 1 FDD connector supported by I/O controller, allowing connection of 1 FDD device

- 6 SATA 3Gb/s connectors (SATAII0, SATAII1, SATAII2, SATAII3, SATAII4, SATAII5), allowing connection of 6 SATA 3Gb/s devices

- Supports data RAID 0, RAID 1, RAID 5, and RAID 10 for Serial ATA

 GIGABYTE SATA2 Controller

- 1 IDE connector with Ultra DMA-33, ATA-66/100/133 support, allowing connection of 2 IDE devices

- 2 SATA 3Gb/s connectors (GSATAII0, GSATAII1), allowing connection of 2 SATA 3Gb/s devices

- Supports data RAID 0, RAID 1 and JBOD for Serial ATA

O.S Support  Microsoft Windows 2000/XP Memory  4 DDRII DIMM memory slots (supports up to 8 GB memory)

 Supports dual channel DDRII 800/667/533 unbuffered DIMMs  Supports 1.8V DDRII DIMMs

Expanstion Slots  1 PCI Express x16 slot (the PCIE_16_1 slot)

 1 PCI Express x4 slot (the PCIE_16_2 slot)  3 PCI Express x1 slots (share the same PCIe bus with the PCIE_16_2 slot)  2 PCI slots

2 Extreme dual-core /

(Note 2)

(Note 3)

GA-965P-DS3P Motherboard - 10 -

Internal Connectors  1 24-pin ATX power connector

 1 8-pin ATX 12V power connector  1 4-pin PCIe 12V power connector  1 floppy connector  1 IDE connector  8 SATA 3Gb/s connectors  1 CPU fan connector  1 system fan connector  1 power fan connector  1 Northbridge fan connector  1 front panel connector  1 front audio connector  1 CD In connector  3 USB 2.0/1.1 connectors for additional 6 ports by cables  2 IEEE 1394a connectors for additional 2 ports by cables  1 S/PDIF In connector  1 power LED connector

Rear Panel I/O  1 PS/2 keyboard port

 1 PS/2 mouse port  1 parallel port  1 S/PDIF out port (coaxial)  1 S/PDIF out port (optical)  1 serial port (COM)  4 USB 2.0/1.1 ports  1 IEEE 1394a port  1 RJ-45 port  6 audio jacks (Line In / Line Out / MIC In / Surround Speaker Out (Rear

Speaker Out) / Center/Subwoofer Speaker Out / Side Speaker Out) I/O Control  IT8718 chip Hardware Monitor  System voltage detection

 CPU / System temperature detection  CPU / System / Power fan speed detection  CPU warning temperature  CPU / System / Power fan failure warning  CPU smart fan control

BIOS  2 8 Mbit flash ROM

 Use of licensed AWARD BIOS  Supports Dual BIOS  PnP 1.0a, DMI 2.0, SM BIOS 2.3, ACPI 1.0b

English

Hardware Installation- 11 -

English

Additional Features  Supports @BIOS

 Supports Download Center  Supports Q-Flash  Supports EasyTune

(Note 4)

 Supports Xpress Install  Supports Xpress Recovery2  Supports Xpress BIOS Rescue

Bundle Software  Norton Internet Security (OEM revision) Overclocking  Over Voltage via BIOS (CPU / DDRII / PCI-E / (G)MCH / FSB)

- CPU Over Voltage : Adjustable CPU voltage at 0.025V

(Note 5)

- DIMM Over Voltage : Adjustable DIMM voltage at 0.025V (Adjustable range from 0.025V to 0.775V)

- PCI-E Over Voltage : Adjustable PCIe voltage at 0.05V (Adjustable range from 0.05V to 0.35V)

- (G)MCH Over Voltage : Adjustable (G)MCH(Northbridge) voltage at 0.05V (Adjustable range from 0.05V to 0.75V)

- FSB Over Voltage : Adjustable FSB voltage at 0.05V (Adjustable range from 0.05V to 0.35V)

 Over Clock via BIOS (CPU / DDR II / PCI-E)

- PCI Express x16 Frequency : Allows 1 MHz increment from 90 MHz to 150 MHz

- Adjustable FSB/ DDRII frequencies

Form Factor  ATX form factor; 30.5cm x 24.4cm

(Note 1) Applies only when the GA-965P-DS3P motherboard (rev. 3.3) is installed with a 1333 MHz

(Note 2) To use a DDR II 800/667 memory module on the motherboard, you must install a 1333/1066/

800 MHz FSB processor. (Note 3) The three PCI Express x1 slots will be unavailable when the PCIE_16_2 slot is in use. (Note 4) EasyTune functions may vary depending on different motherboards. (Note 5) The adjustable range is dependent on CPUs.

GA-965P-DS3P Motherboard - 12 -

1-3 Installation of the CPU and CPU Cooler

Before installing the CPU, please comply with the following conditions:

1. Please make sure that the motherboard supports the CPU.

2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong direction, the CPU will not insert properly. If this occurs, please change the insert direction of the CPU.

3. Please add an even layer of heat sink paste between the CPU and CPU cooler.

4. Please make sure the CPU cooler is installed on the CPU prior to system use, otherwise overheating and permanent damage of the CPU may occur.

5. Please set the CPU host frequency in accordance with the processor specifications. It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the required standards for the peripherals. If you wish to set the frequency beyond the proper specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc.

HT functionality requirement content :

Enabling the functionality of Hyper-Threading Technology for your computer system requires all of the following platform components:

- CPU: An Intel® Pentium 4 Processor with HT Technology

- Chipset: An Intel® Chipset that supports HT Technology

- BIOS: A BIOS that supports HT Technology and has it enabled

- OS: An operation system that has optimizations for HT Technology

1-3-1 Installation of the CPU

Metal Lever

Fig. 1 Gently lift the metal lever located on the CPU socket to the upright position.

English

Fig. 2 Remove the plastic covering on the CPU socket.

Fig. 3 Notice the small gold colored triangle located on the edge of the CPU socket. Align the indented corner of the

CPU with the triangle and gently insert the CPU into position. (Grasping the CPU firmly between your thumb and forefinger, carefully place it into the socket in a straight and downwards motion. Avoid twisting or bending motions that might cause damage to the CPU during installation.)

Fig. 4 Once the CPU is properly inserted, please replace the load plate and push the metal lever back into its original position.

Hardware Installation- 13 -

1-3-2 Installation of the CPU Cooler

Male Push Pin

English

Fig.1 Please apply an even layer of CPU cooler paste on the surface of the installed CPU.

Fig. 3 Place the CPU cooler atop the CPU and make sure the push pins aim to the pin hole on the motherboard.Pressing down the push pins diagonally.

The top of Female Push Pin

Female Push Pin

Fig. 2 (Turning the push pin along the direction of arrow is to remove the CPU cooler, on the contrary, is to install.) Please note the direction of arrow sign on the male push pin doesn't face inwards before installation. (This instruction is only for Intel boxed fan)

Fig. 4 Please make sure the Male and Female push pin are joined closely. (for detailed installation instructions, please refer to the CPU cooler installation section of the user manual)

Fig. 5 Please check the back of motherboard after installing. If the push pin is inserted as the picture, the installation is complete.

The CPU cooler may adhere to the CPU as a result of hardening of the heat paste. To prevent such an occurrence, it is suggested that either thermal tape rather than heat paste be used for heat dissipation or using extreme care when removing the CPU cooler.

GA-965P-DS3P Motherboard - 14 -

Fig. 6 Finally, please attach the power connector of the CPU cooler to the CPU fan header located on the motherboard.

1-4 Installation of Memory

Before installing the memory modules, please comply with the following conditions:

1. Please make sure that the memory used is supported by the motherboard. It is recommended that memory of similar capacity, specifications and brand be used.

2. Before installing or removing memory modules, please make sure that the computer power is switched off to prevent hardware damage.

3. Memory modules have a foolproof insertion design. A memory module can be installed in only one direction. If you are unable to insert the module, please switch the direction.

The motherboard supports DDRII memory modules, whereby BIOS will automatically detect memory capacity and specifications. Memory modules are designed so that they can be inserted only in one direction. The memory capacity used can differ with each slot.

Notch

DDRII

English

Fig.1 The DIMM socket has a notch, so the DIMM memory module can only fit in one direction. Insert the DIMM memory module vertically into the DIMM socket. Then push it down.

Fig.2 Close the plastic clip at both edges of the DIMM sockets to lock the DIMM module. Reverse the installation steps when you wish to remove the DIMM module.

Hardware Installation- 15 -

English

Dual Channel Memory Configuration

The GA-965P-DS3P supports the Dual Channel Technology. After operating the Dual Channel Technology, the bandwidth of memory bus will double.

The GA-965P-DS3P includes 4 DIMM sockets, and each Channel has two DIMM sockets as following:

Channel 0 : DDRII1, DDRII2

Channel 1 : DDRII3, DDRII4 If you want to operate the Dual Channel Technology, please note the following explanations due to the limitation of Intel chipset specifications.

1. Dual Channel mode will not be enabled if only one DDRII memory module is installed.

2. To enable Dual Channel mode with two or four memory modules (it is recommended to use memory modules of identical brand, size, chips, and speed), you must install them into DIMM sockets of the same color.

The following is a Dual Channel Memory configuration table: (DS: Double Side, SS: Single Side, "--": Empty)

DDRII1 DDRII2 DDRII3 DDRII4

2 memory modules

4 memory modules

(Note) When memory modules of different size and chips are installed, a message which indicates

that memory is configured to Flex memory mode operation will appear during POST. Intel® Flex Memory Technology offers easier upgrades by allowing different memory sizes to be populated and remain in dual-channel mode.

DS/SS - - DS/SS - -

- - DS/SS - - DS/SS

DS/SS DS/SS DS/SS DS/SS

GA-965P-DS3P Motherboard - 16 -

1-5 Installation of Expansion Cards

To install your expansion card, follow the steps below.

1. Disconnect your system from its power source and read the expansion card's installation manual before installing the expansion card in the computer.

2. Remove your computer's chassis cover, screws and slot bracket from the computer. Ground yourself to prevent damage to your computer resulting from Electrostatic discharge (ESD).

3. Press the expansion card firmly into the expansion slot in the motherboard.

4. Make sure the metal contacts on the card are fully seated in the slot.

5. Replace the screw to secure the slot bracket of the expansion card.

6. Replace your computer's chassis cover.

7. Power on the computer, if necessary, configure required settings for the expansion card in system BIOS Setup.

8. Install related driver in the operating system.

For example: Installing a PCI Express x16 VGA card:

To install the VGA card: Please align the VGA card with the PCI Express x16 slot and press down on the card. Make sure the VGA card is locked by the small white drawable bar.

To remove the VGA card from the PCIE_16_1 slot: Please carefully pull out the small white-drawable bar at the end of the PCIE_16 slot when you try to uninstall the VGA card.

English

Or you can also press the latch on the opposite side of the drawable bar as the picture to the left shows.

To remove the VGA card from the PCIE_16_2 slot: When you try to uninstall the VGA card on the PCIE_16_2 slot, you can press the latch as the picture to the left shows to release the card.

The motherboard includes a PCIE_12V power connector, which provides extra power to the onboard PCI Express x16 slot. When installing two graphics cards, please connect the power cable from the power supply to this connector.

Hardware Installation- 17 -

English

1-6 I/O Back Panel Introduction

PS/2 Keyboard and PS/2 Mouse Connector

To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the lower port (purple).

Parallel Port

The parallel port allows connection of a printer, scanner and other peripheral devices.

COATIAL

The SPDIF coaxial output port is capable of providing digital audio to external speakers or compressed AC3 data to an external Dolby Digital Decoder via a coaxial cable.

OPTICAL

The SPDIF optical output port is capable of providing digital audio to external speakers or compressed AC3 data to an external Dolby Digital Decoder via an optical cable.

COM (Serial Port)

Connects to serial-based mouse or data processing devices.

IEEE 1394a Port

Serial interface standard set by Institute of Electrical and Electronics Engineers, which has features like high speed, high bandwidth and hot plug.

USB port

Before you connect your device(s) into USB connector(s), please make sure your device(s) such as USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface. Also make sure your OS supports USB controller. If your OS does not support USB controller, please contact OS vendor for possible patch or driver upgrade. For more information please contact your OS or device(s) vendors.

LAN Port

The provided Internet connection is Gigabit Ethernet , providing data transfer speeds of 10/100/ 1000 Mbps.

Center/Subwoofer Speaker Out

The default Center/Subwoofer Speaker Out jack. Center/Subwoofer speakers can be connected to Center/Subwoofer Speaker Out jack.

Surround Speaker Out (Rear Speaker Out)

The default Surround Speaker Out (Rear Speaker Out) jack. Rear surround speakers can be connected to Surround Speaker Out (Rear Speaker Out) jack.

Side Speaker Out

The default Side Speaker Out jack. Surround side speakers can be connected to Side Speaker Out jack.

Line In

The default Line In jack. Devices like CD-ROM, walkman etc. can be connected to Line In jack.

GA-965P-DS3P Motherboard - 18 -

Line Out (Front Speaker Out)

The default Line Out (Front Speaker Out) jack. Stereo speakers, earphone or front surround speakers can be connected to Line Out (Front Speaker Out) jack.

MIC In

The default MIC In jack. Microphone must be connected to MIC In jack.

In addition to the default speakers settings, the ~ audio jacks can be reconfigured to perform different functions via the audio software. Only microphones still MUST be connected to the default Mic In jack ( ). Please refer to the 2-/4-/6-/8- channel audio setup steps for detailed software configuration information.

1-7 Connectors Introduction

English

1) ATX_12V_2X

2) ATX (Power Connector)

3) PCIE_12V

4) CPU_FAN

5) SYS_FAN

6) PWR_FAN

7) NB_FAN

8) FDD

9) IDE

10) SATAII0 / 1 / 2 / 3 / 4 / 5

11) GSATAII0 / GSATAII1

1 4

5 12

1518

12) PWR_LED

13) BATTERY

14) F_AUDIO

15) F_PANEL

16) CD_IN

17) SPDIF_IN

18) F_USB1 / F_USB2 / F_USB3

19) F1_1394 / F2_1394

20) C I

21) CLR_CMOS

Hardware Installation- 19 -

English

1/2) ATX_12V_2X / ATX (Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, please make sure that all components and devices are properly installed. Align the power connector with its proper location on the motherboard and connect tightly. The ATX 12V (2x4-pin) power connector mainly supplies power to the CPU. If the ATX 12V (2x4) power connector is not connected, the system will not start. If you wish to install a power supply that provides ATX 12V (2x2-pin) power connector, please connect the ATX 12V power connector to the Pin 3, 4, 7, 8 of the onboard ATX_12V_2X power connector according to the pin definitions. Important Use of a power supply providing an ATX 12V (2x4-pin) power connector is recommended by processor manufacturer when using Intel® Pentium® Extreme Edition series processors (130W or greater). Caution! Please use a power supply that is able to handle the system voltage requirements. It is recommended that a power supply that can withstand high power consumption be used (400W or greater). If a power supply is used that does not provide the required power, the result can lead to an unstable system or a system that is unable to start. If you use a power supply that provides a 24-pin ATX or 2x4 pin ATX 12V power connector, please remove the small cover on the power connector on the motherboard before plugging in the power cord; otherwise, please do not remove it.

Pin No. Definition

ATX_12V_2X

1 GND

2 GND

3 GND

4 GND

5 +12V

6 +12V

7 +12V

8 +12V

131

ATX

Pin No. Definition

1 3.3V

2 3.3V

3 GND

4 +5V

5 GND

6 +5V

7 GND

8 Power Good

9 5V SB(stand by +5V)

10 +12V

11 +12V(Only for 24-pin ATX)

12 3.3V(Only for 24-pin ATX)

GA-965P-DS3P Motherboard - 20 -

Pin No. Definition

13 3.3V

14 -12V

15 GND

16 PS_ON(soft On/Off)

17 GND

18 GND

19 GND

20 -5V

21 +5V

22 +5V

23 +5V (Only for 24-pin ATX)

24 GND(Only for 24-pin ATX)

3) PCIE_12V (Power Connector)

This power connector provides extra power to the onboard PCI Express x16 slot. When installing two graphics cards, please connect the power cable from the power supply to this connector, or system instability may occur.

English

PIin No. Definition

1NC

2 GND

3 GND

4 +12V

4/5/6) CPU_FAN / SYS_FAN / PWR_FAN (Cooler Fan Power Connector)

The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin(CPU_FAN/ SYS_FAN) power connector and possesses a foolproof connection design. Most coolers are designed with color-coded power connector wires. A red power connector wire indicates a positive connection and requires a +12V power voltage. The black connector wire is the ground wire (GND). Remember to connect the CPU/system/power fan cable to the CPU_FAN/SYS_FAN/PWR_FAN connector to prevent CPU damage or system hanging caused by overheating.

CPU_FAN / SYS_FAN :

CPU_FAN

Pin No. Definition

1 GND

2 +12V / Speed Control

3 Sense

4 Speed Control

SYS_FAN

PWR_FAN

PWR_FAN :

Pin No. Definition

1 GND

2 +12V

3 Sense

Hardware Installation- 21 -

English

7) NB_FAN (Chip Fan Connector)

If you installed wrong direction, the chip fan will not work. Sometimes will damage the chip fan. (Usually black cable is GND)

Pin No. Definition

1 +12V

2 GND

8) FDD (Floppy Connector)

The FDD connector is used to connect the FDD cable while the other end of the cable connects to the FDD drive. The types of FDD drives supported are: 360 KB, 720 KB, 1.2 MB, 1.44 MB and

2.88 MB. Before attaching the FDD cable, please take note of the foolproof groove in the FDD connector.

GA-965P-DS3P Motherboard - 22 -

9) IDE (IDE Connector)

An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If you wish to connect two IDE devices, please set the jumper on one IDE device as Master and the other as Slave (for information on settings, please refer to the instructions located on the IDE device). Before attaching the IDE cable, please take note of the foolproof groove in the IDE connector.

4039

10) SATAII0 / 1 / 2 / 3 / 4 / 5 (SATA 3Gb/s Connector, Controlled by ICH8R)

SATA 3Gb/s can provide up to 300 MB/s transfer rate. Please refer to the BIOS setting for the SATA 3Gb/s and install the proper driver in order to work properly.

SATAII0

English

SATAII1

SATAII4

SATAII5

SATAII2

SATAII3

Pin No. Definition

1 GND

2 TXP

3 TXN

4 GND

5 RXN

6 RXP

7 GND

Hardware Installation- 23 -

English

11) GSATAII0 / GSATAII1 (SATA 3Gb/s Connector, Controlled by GIGABYTE SATA2)

SATA 3Gb/s can provide up to 300 MB/s transfer rate. Please refer to the BIOS setting for the SATA 3Gb/s and install the proper driver in order to work properly.

GSATAII0

GSATAII1

Pin No. Definition

1 GND

2 TXP

3 TXN

4 GND

5 RXN

6 RXP

7 GND

12) PWR_LED

The PWR_LED connector is connected with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode(S1).

GA-965P-DS3P Motherboard - 24 -

Pin No. Definition

1 MPD+

2 MPD-

3 MPD-

13) BATTERY

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended

by the manufacturer.

Dispose of used batteries according to the manufacturer's

instructions.

If you want to erase CMOS...

1. Turn off the computer and unplug the power cord.

2. Gently take out the battery and put it aside for about one minute.

(Or you can use a metal object to connect the positive and

negative pins in the battery holder to make them short for five

seconds.)

3. Re-install the battery.

4. Plug the power cord in and turn on the computer.

14) F_AUDIO (Front Audio Connector)

This connector supports either HD (High Definition) or AC97 front panel audio module. If you wish to use the front audio function, connect the front panel audio module to this connector. Check the pin assignments carefully while you connect the front panel audio module. Incorrect connection between the module and connector will make the audio device unable to work or even damage it. For optional front panel audio module, please contact your chassis manufacturer.

English

HD Audio:

Pin No. Definition

1 MIC2_L

2 GND

3 MIC2_R

4 -ACZ_DET

5 LINE2_R

6 FSENSE1

7 FAUDIO_JD

8 No Pin

9 LINE2_L

10 FSENSE2

AC'97 Audio:

Pin No. Definition

1 MIC

2 GND

3 MIC Power

4NC

5 Line Out (R)

6NC

7NC

8 No Pin

9 Line Out (L)

10 NC

By default, the audio driver is configured to support HD Audio. To connect an AC97 front panel audio module to this connector, please refer to the instructions on page 92 about the software settings.

Hardware Installation- 25 -

English

15) F_PANEL (Front Panel Jumper)

Please connect the power LED, PC speaker, reset switch and power switch etc. of your chassis front panel to the F_PANEL connector according to the pin assignment below.

Message LED/

Power/

Sleep LED

MSG+

2 1

HD+

IDE Hard Disk Active LED

MSG (Message LED/Power/Sleep LED) Pin 1: LED anode(+)

(Yellow) Pin 2: LED cathode(-)

PW (Power Switch) Open: Normal

(Red) Cl ose : Power On/Off

SPEAK (Speaker Connector) Pin 1: Power

(Amber) Pin 2- Pin 3: NC

Pin 4: Data(-)

HD (IDE Hard Disk Active LED) Pin 1: LED anode(+)

(Blue) Pin 2: LED cathode(-)

RES (Reset Switch) Open: Normal

(Green) Close: Reset Hardware System

NC ( Purple) NC

Power

Switch

PW+

PW-

MSG-

HD-

RES+

RES-

Reset Switch

Speaker Connector

SPEAK+

SPEAK-

GA-965P-DS3P Motherboard - 26 -

16) CD_IN (CD IN Connector)

Connect CD-ROM or DVD-ROM audio out to the connector.

English

Pin No. Definition

1 CD-L

2 GND

3 GND

4 CD-R

17) SPDIF_IN (S/PDIF In Connector)

Use S/PDIF IN feature only when your device has digital output function. Be careful with the polarity of the SPDIF_IN connector. Check the pin assignment carefully while you connect the S/PDIF cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional S/PDIF cable, please contact your local dealer.

Pin No. Definition

1 Power

2 SPDIFI

3 GND

Hardware Installation- 27 -

English

18) F_ USB1 / F_USB2 / F_USB3 (Front USB Connector)

Be careful with the polarity of the front USB connector. Check the pin assignment carefully while you connect the front USB cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional front USB cable, please contact your local dealer.

910

Pin No. Definition

1 Power (5V)

2 Power (5V)

3 USB DX-

4 USB Dy-

5 USB DX+

6 USB Dy+

7 GND

8 GND

9 No Pin

10 NC

19) F1_1394 / F2_1394 (Front IEEE 1394 Connector)

Serial interface standard set by Institute of Electrical and Electronics Engineers, which has features like high speed, high bandwidth and hot plug. Be careful with the polarity of the IEEE 1394 connector. Check the pin assignment carefully while you connect the IEEE 1394 cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional IEEE 1394 cable, please contact your local dealer.

Pin No. Definition

1TPA+

2TPA-

3 GND

4 GND

5 TPB+

6 TPB-

7 Power (12V)

8 Power (12V)

9 No Pin

10 GND

GA-965P-DS3P Motherboard - 28 -

20) CI (Chassis Intrusion, Case Open)

This 2-pin connector allows your system to detect if the chassis cover is removed. You can check the "Case Opened" status in BIOS Setup.

English

Pin No. Definition

1 Signal

2 GND

21) CLR_CMOS (Clear CMOS)

You may clear the CMOS data to its default values by this header. To clear CMOS, temporarily short the two pins. Default doesn't include the jumper to avoid improper use of this header.

Open: Normal

Short: Clear CMOS

Hardware Installation- 29 -

+ 67 hidden pages