Gigabyte GA-965GM-DS2, GA-965GM-S2 User Manual

GA-965GM-DS2 / GA-965GM-S2
TM
Intel® Core Intel® Core
2 Extreme quad-core / Core
TM
2 Extreme dual-core / Core Intel® Pentium® Processor Extreme Edition / Intel® Pentium® D / Pentium® 4 LGA775 Processor Motherboard
User's Manual
Rev. 2031
12ME-965GMDR-2031R
TM
TM
2 Duo /
* The WEEE marking on the product indicates this product must not be disposed of with user's other household waste
and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!
* The WEEE marking applies only in European Union's member states.
Oct. 1, 2006
GA-965GM-DS2 / GA-965GM-S2
Motherboard
Oct. 1, 2006
GA-965GM-DS2 /
GA-965GM-S2
Motherboard
Copyright
© 2007 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in the manual are legally registered to their respective companies.
Notice
The written content provided with this product is the property of Gigabyte.
No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any
means without Gigabyte's prior written permission. Specifications and features are subject to
change without prior notice.
Product Manual Classification
In order to assist in the use of this product, Gigabyte has categorized the user manual in the
following:
For detailed product information and specifications, please carefully read the
"Product User Manual".
For detailed information related to Gigabyte's unique features, please go to the
"Technology Guide" section on Gigabyte's website to read or download the information
you need.
For more product details, please visit Gigabyte's website at www.gigabyte.com.tw
Table of Contents
Item Checklist ................................................................................................................. 6
Optional Accessories ...................................................................................................... 6
GA-965GM-DS2 / GA-965GM-S2 Motherboard Layout ................................................. 7
Block Diagram ................................................................................................................ 8
Chapter 1 Hardware Installation .................................................................................... 9
1-1 Considerations Prior to Installation .................................................................... 9
1-2 Feature Summary .......................................................................................... 10
1-3 Installation of the CPU and CPU Cooler ....................................................... 12
1-3-1 Installation of the CPU ......................................................................................... 12
1-3-2 Installation of the CPU Cooler ............................................................................ 13
1-4 Installation of Memory .................................................................................... 14
1-5 Installation of Expansion Cards ...................................................................... 16
1-6 I/O Back Panel Introduction ........................................................................... 17
1-7 Connectors Introduction .................................................................................. 18
Chapter 2 BIOS Setup ................................................................................................ 29
The Main Menu (For example: GA-965GM-DS2 BIOS Ver.: F1) ............................. 30
2-1 Standard CMOS Features ............................................................................. 32
2-2 Advanced BIOS Features .............................................................................. 34
2-3 Integrated Peripherals ..................................................................................... 36
2-4 Power Management Setup ............................................................................. 39
2-5 PnP/PCI Configurations ................................................................................. 40
2-6 PC Health Status ........................................................................................... 41
2-7 Frequency/Voltage Control ............................................................................. 43
2-8 Load Fail-Safe Defaults ................................................................................... 44
2-9 Load Optimized Defaults ................................................................................. 44
2-10 Set Supervisor/User Password ..................................................................... 45
2-11 Save & Exit Setup......................................................................................... 46
2-12 Exit Without Saving ....................................................................................... 46
- 4 -
Chapter 3 Install Drivers ............................................................................................. 47
3-1 Install Chipset Drivers .................................................................................... 47
3-2 Software Applications ..................................................................................... 48
3-3 Driver CD Information .................................................................................... 48
3-4 Hardware Information ..................................................................................... 49
3-5 Contact Us ..................................................................................................... 49
Chapter 4 Appendix ................................................................................................... 51
4-1 Unique Software Utilities ................................................................................ 51
4-1-1 EasyTune 5 Introduction ..................................................................................... 51
4-1-2 Xpress Recovery2 Introduction ......................................................................... 52
4-1-3 Flash BIOS Method Introduction ........................................................................ 54
4-1-4 Configuring SATA Hard Drive(s) (Controller: GIGABYTE SATA2) ................ 63
4-1-5 2- / 4- / 6- / 8- Channel Audio Function Introduction ...................................... 76
4-2 Troubleshooting ............................................................................................... 81
- 5 -
Item Checklist
IDE Cable x 1, FDD Cable x 1
SATA 3Gb/s Cable x 2
I/O Shield
* The items listed above are for reference only, and are subject to change without notice.
Optional Accessories
2 Ports USB 2.0 Cable (Part Number: 12CR1-1UB030-51/R)
4 Ports USB 2.0 Cable (Part Number: 12CR1-1UB030-21/R)
COM Port Cable (Part Number: 12CF1-1CM001-31/12CF1-1CM001-12R)
SPDIF In and Out Cable (Part Number: 12CR1-1SPINO-11/R)
e-SATA Cable (Part Number: 12CF1-3SATPW-01R/11R)
- 6 -
GA-965GM-DS2 / GA-965GM-S2 Motherboard Layout
KB_MS
COMA
VGA
USB_1394
USB_LAN
AUDIO
Marvell
88E8056
CD_IN
CODEC
ATX_12V
LPT
F_AUDIO
COMB
PCIE_1
LGA775
Intel® G965
CI
CLR_CMOS
F1_1394
PCI1
PCI2
BATTERY
F2_1394
PCIE_16
F_USB2
CPU_FAN
GA-965GM-DS2 / GA-965GM-S2
DDRII1
DDRII2
DDRII4
DDRII3
BIOS
Intel® ICH8
F_USB3
SATAII2
SATAII3
GIGABYTE SATA2
IT8718
FDD
ATX
IDE
F_PANEL
PWR_LED
SPDIF_IO
SYS _FAN
- 7 -
F_USB1
SATAII0
SATAII1
GSATAII0
GSATAII1
Block Diagram
PCIe CLK (100 MHz)
LGA775
Processor
CPU CLK+/-(266/200/133 MHz)
ATA-33/66/100/133
IDE Channel
PCI Express Bus
PCIe CLK
(100 MHz)
1 PCI Express x1
PCI Express x16
2 SATA 3Gb/s
GIGABYTE
SATA2
x1
PCI Bus
TSB43AB23
RJ45
Marvell
88E8056
x1
VGA
LAN
x1
Intel ICH8
CODEC
Host Interface
®
Intel G965
®
DDRII 800/667/533 MHz DIMM
Dual Channel Memory
GMCH CLK (266/200/133 MHz)
BIOS
4 SATA 3Gb/s
LPT
IT8718
Floppy
COM Ports
PS/2 KB/Mouse
(Note)
2 PCI
MIC
Line-Out
3 IEEE 1394a
Side Speaker Out
Line-In
SPDIF In
10 USB
Ports
SPDIF Out
Surround Speaker Out
PCI CLK(33 MHz)
Center/Subwoofer Speaker Out
(Note) To use a DDR II 800/667 memory module on the motherboard, you must install an 1066/
800 MHz FSB processor.
- 8 -
Chapter 1Hardware Installation
1-1 Considerations Prior to Installation
Preparing Your Computer
The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please follow the instructions below:
1. Please turn off the computer and unplug its power cord.
2. When handling the motherboard, avoid touching any metal leads or connectors.
3. It is best to wear an electrostatic discharge (ESD) cuff when handling electronic components
(CPU, RAM).
4. Prior to installing the electronic components, please have these items on top of an antistatic
pad or within a electrostatic shielding container.
5. Please verify that the power supply is switched off before unplugging the power supply connector
from the motherboard.
Installation Notices
1. Prior to installation, please do not remove the stickers on the motherboard. These stickers
are required for warranty validation.
2. Prior to the installation of the motherboard or any hardware, please first carefully read the
information in the provided manual.
3. Before using the product, please verify that all cables and power connectors are connected.
4. To prevent damage to the motherboard, please do not allow screws to come in contact with
the motherboard circuit or its components.
5. Please make sure there are no leftover screws or metal components placed on the motherboard
or within the computer casing.
6. Please do not place the computer system on an uneven surface.
7. Turning on the computer power during the installation process can lead to damage to system
components as well as physical harm to the user.
8. If you are uncertain about any installation steps or have a problem related to the use of the
product, please consult a certified computer technician.
English
Instances of Non-Warranty
1. Damage due to natural disaster, accident or human cause.
2. Damage as a result of violating the conditions recommended in the user manual.
3. Damage due to improper installation.
4. Damage due to use of uncertified components.
5. Damage due to use exceeding the permitted parameters.
6. Product determined to be an unofficial Gigabyte product.
Hardware Installation- 9 -
English
1-2 Feature Summary
TM
CPU LGA775 for Intel® Core
2 Extreme quad-core / Core CoreTM 2 Quad / CoreTM 2 Duo / Pentium® processor Extreme Edition / Pentium® D / Pentium® 4 / Celeron® D
L2 cache varies with CPU Front Side Bus  Supports 1066/800/533 MHz FSB Chipset Northbridge: Intel® G965 Express Chipset
Southbridge: Intel® ICH8 LAN Onboard Marvell 88E8056 phy (10/100/1000 Mbit) Audio Onboard Realtek ALC888 CODEC chip
Supports High Definition Audio
Supports 2 / 4 / 6 / 8 channel audio
Supports SPDIF In/Out connection
Supports CD In connection
Storage ICH8 Southbrigde
- 1 FDD connector, allowing connection of 1 FDD device
- 4 SATA 3Gb/s connectors (SATAII0,1, 2, 3), allowing connection of 4 SATA 3Gb/s devices
Onboard GIGABYTE SATA2 chip
- 1 IDE connector (ATA-33/66/100/133), allowing connection of 2 IDE devices
- 2 SATA 3Gb/s connectors (GSATAII0,1), allowing connection of 2 SATA 3Gb/s devices
- Supports data striping (RAID 0), mirroring (RAID 1), and JBOD for Serial ATA
O.S Support Microsoft Windows 2000/XP Memory 4 DDRII DIMM memory slots (supports up to 8 GB memory)
Supports dual channel DDRII 800/667/533 unbuffered DIMMs  Supports 1.8V DDRII DIMMs
Expanstion Slots 1 PCI Express x16 slot
1 PCI Express x1 slot2 PCI slots
Internal Connectors 1 24-pin ATX power connector
1 4-pin ATX 12V power connector1 floppy connector1 IDE connector6 SATA 3Gb/s connectors1 CPU fan connector1 system fan connector1 front panel connector1 front audio connector1 CD In connector1 power LED connector
TM
2 Extreme dual-core /
(Note 1)
"*" Only the GA-965GM-DS2 adopts All-Solid Capacitor design.
GA-965GM-(D)S2 Motherboard - 10 -
Internal Connectors 3 USB 2.0/1.1 connectors for additional 6 USB 2.0/1.1 ports by cables
1 SPDIF In/Out connector2 IEEE 1394a connectors for additional 2 ports by cable1 COMB connector1 Chassis Intrusion connector
Rear Panel I/O 1 PS/2 keyboard port
1 PS/2 mouse port1 parallel port1 VGA port1 serial port (COMA)4 USB 2.0/1.1 ports1 IEEE 1394a port1 RJ-45 port6 audio jacks (Line In / Line Out / MIC In/Surround Speaker Out (Rear
Speaker Out)/Center/Subwoofer Speaker Out/Side Speaker Out) I/O Control IT8718 chip Hardware Monitor System voltage detection
CPU / System temperature detectionCPU / System fan speed detectionCPU warning temperatureCPU / System fan failure warningCPU Smart Fan Control
BIOS 1 8 Mbit flash ROM
Use of licensed AWARD BIOSPnP 1.0a, DMI 2.0, SM BIOS 2.3, ACPI 1.0b
Additional Features Supports @BIOS
Supports Download CenterSupports Q-FlashSupports EasyTune(only supports Hardware Monitor function) Supports Xpress InstallSupports Xpress Recovery2Supports Xpress BIOS Rescue
Bundle Software Norton Internet Security (OEM version) Form Factor Micro ATX form factor; 24.4cm x 24.4cm
(Note 2)
English
(Note 1) To use a DDR II 800/667 memory module on the motherboard, you must install an 1066/
800 MHz FSB processor.
(Note 2) EasyTune functions may vary depending on different motherboards.
Hardware Installation- 11 -
1-3 Installation of the CPU and CPU Cooler
English
Before installing the CPU, please comply with the following conditions:
1. Please make sure that the motherboard supports the CPU.
2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong direction, the CPU will not insert properly. If this occurs, please change the insert direction of the CPU.
3. Please add an even layer of heat sink paste between the CPU and heatsink.
4. Please make sure the heatsink is installed on the CPU prior to system use, otherwise overheating and permanent damage of the CPU may occur.
5. Please set the CPU host frequency in accordance with the processor specifications. It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the required standards for the peripherals. If you wish to set the frequency beyond the proper specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc.
HT functionality requirement content :
Enabling the functionality of Hyper-Threading Technology for your computer system requires all of the following platform components:
- CPU: An Intel® Pentium 4 Processor with HT Technology
- Chipset: An Intel® Chipset that supports HT Technology
- BIOS: A BIOS that supports HT Technology and has it enabled
- OS: An operation system that has optimizations for HT Technology
1-3-1 Installation of the CPU
Metal Lever
Fig. 1 Gently lift the metal lever located on the CPU socket to the upright position.
Fig. 2 Remove the plastic covering on the CPU socket.
Fig. 3 Notice the small gold colored triangle lo­cated on the edge of the CPU socket. Align the indented cor-
ner of the CPU with the triangle and gently insert the CPU into position. (Grasping the CPU firmly between your thumb and forefinger, carefully place it into the socket in a straight and downwards motion. Avoid twisting or bending motions that might cause damage to the CPU during installation.)
GA-965GM-(D)S2 Motherboard - 12 -
Fig. 4 Once the CPU is properly inserted, please replace the plastic covering and push the metal lever back into its original position.
1-3-2 Installation of the CPU Cooler
English
Male Push Pin
The top of Female Push Pin
Female Push Pin
Fig.1 Please apply an even layer of CPU cooler paste on the surface of the installed CPU.
Fig. 3 Place the CPU cooler atop the CPU and make sure the push pins aim to the pin hole on the motherboard.Pressing down the push pins diagonally.
Fig. 5 Please check the back of motherboard after installing. If the push pin is inserted as the picture, the installation is complete.
Fig. 2 (Turning the push pin along the direction of arrow is to remove the CPU cooler, on the contrary, is to install.) Please note the direction of arrow sign on the male push pin doesn't face inwards before installation. (This instruction is only for Intel boxed fan)
Fig. 4 Please make sure the Male and Female push pin are joined closely. (for detailed installation instructions, please refer to the CPU cooler instal­lation section of the user manual)
Fig. 6 Finally, please attach the power connector of the CPU cooler to the CPU fan header located on the motherboard.
The CPU cooler may adhere to the CPU as a result of hardening of the heat paste. To prevent such an occurrence, it is suggested that either thermal tape rather than heat paste be used for heat dissipation or using extreme care when removing the CPU cooler.
Hardware Installation- 13 -
English
1-4 Installation of Memory
Before installing the memory modules, please comply with the following conditions:
1. Please make sure that the memory used is supported by the motherboard. It is recommended that memory of similar capacity, specifications and brand be used.
2. Before installing or removing memory modules, please make sure that the computer power is switched off to prevent hardware damage.
3. Memory modules have a foolproof insertion design. A memory module can be installed in only one direction. If you are unable to insert the module, please switch the direction.
The motherboard supports DDRII memory modules, whereby BIOS will automatically detect memory capacity and specifications. Memory modules are designed so that they can be inserted only in one direction. The memory capacity used can differ with each slot.
Notch
DDRII
Fig.1 The DIMM socket has a notch, so the DIMM memory mod­ule can only fit in one direction. Insert the DIMM memory module vertically into the DIMM socket. Then push it down.
Fig.2 Close the plastic clip at both edges of the DIMM sockets to lock the DIMM module. Reverse the installation steps when you wish to remove the DIMM module.
GA-965GM-(D)S2 Motherboard - 14 -
Dual Channel Memory Configuration
The GA-965GM-DS2 / GA-965GM-S2 supports the Dual Channel Technology. After operating the Dual Channel Technology, the bandwidth of memory bus will double. The GA-965GM-DS2 / GA-965GM-S2 includes 4 DIMM sockets, and each
Channel has two DIMM sockets as following:
Channel 0 : DDRII1, DDRII2 Channel 1 : DDRII3, DDRII4
If you want to operate the Dual Channel Technology, please note the following explanations due to the limitation of Intel chipset specifications.
1. Dual Channel mode will not be enabled if only one DDRII memory module is installed.
2. To enable Dual Channel mode with two or four memory modules (it is recommended to use memory modules of identical brand, size, chips, and speed), you must install them into DIMM sockets of the same color.
The following is a Dual Channel Memory configuration table: (DS: Double Side, SS: Single Side, X:Empty)
DDRII1 DDRII2 DDRII3 DDRII4
2 memory modules
4 memory modules
(Note) When memory modules of different size and chips are installed, a message which indicates
that memory is configured to Flex memory mode operation will appear during POST. Intel® Flex Memory Technology offers easier upgrades by allowing different memory sizes to be populated and remain in dual-channel mode.
DS/SS X DS/SS X
X DS/SS X DS/SS
DS/SS DS/SS DS/SS DS/SS
English
Hardware Installation- 15 -
English
1-5 Installation of Expansion Cards
You can install your expansion card by following the steps outlined below:
1. Read the related expansion card's instruction document before install the expansion card into the computer.
2. Remove your computer's chassis cover, screws and slot bracket from the computer.
3. Press the expansion card firmly into expansion slot in motherboard.
4. Be sure the metal contacts on the card are indeed seated in the slot.
5. Replace the screw to secure the slot bracket of the expansion card.
6. Replace your computer's chassis cover.
7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.
8. Install related driver from the operating system.
Installing a PCI Express x16 expansion card:
Please carefully pull out the small white­drawable bar at the end of the PCI Express x16 slot when you try to install/ uninstall the VGA card. Please align the VGA card to the onboard PCI Express x16 slot and press firmly down on the slot. Make sure your VGA card is locked by the small white-drawable bar.
GA-965GM-(D)S2 Motherboard - 16 -
To install a VGA card or to release an installed card, users can also press the latch on the back of the drawable bar as the picture to the left shows.
1-6 I/O Back Panel Introduction
PS/2 Keyboard and PS/2 Mouse Connector
To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the lower port (purple).
Parallel Port (LPT)
The parallel port allows connection of a printer, scanner and other peripheral devices.
Serial Port (COMA)
Devices like mouses, modems, and etc. can be connected to Serial port.
VGA Port
Monitor can be connected to VGA port.
IEEE 1394 port
Connectec to IEEE 1394 devices.
USB port
Before you connect your device(s) into USB connector(s), please make sure your device(s) such as USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface. Also make sure your OS supports USB controller. If your OS does not supportUSB controller, please con­tact OS vendor for possible patch or driver upgrade. For more information please contact your OS or device(s) vendors.
LAN Port
The provided Internet connection is Gigabit Ethernet, providing data transfer speeds of 10/100/ 1000 Mbps.
Center/Subwoofer Speaker Out
The default Center/Subwoofer Speaker Out jack. Center/Subwoofer speakers can be connected to Center/Subwoofer Speaker Out jack.
Surround Speaker Out (Rear Speaker Out)
The default Surround Speaker Out (Rear Speaker Out) jack. Rear surround speakers can be connected to Surround Speaker Out (Rear Speaker Out) jack.
Side Speaker Out
The default Side Speaker Out jack. Surround side speakers can be connected to Side Speaker Out jack.
Line In
The default Line In jack. Devices like CD-ROM, walkman etc. can be connected to Line In jack.
English
Hardware Installation- 17 -
English
Line Out (Front Speaker Out)
The default Line Out (Front Speaker Out) jack. Stereo speakers, earphone or front surround speakers can be connected to Line Out (Front Speaker Out) jack.
MIC In
The default MIC In jack. Microphone must be connected to MIC In jack.
In addition to the default speakers settings, the ~ audio jacks can be reconfigured to
perform different functions via the audio software. Only microphones still MUST be connected
to the default Mic In jack ( ). Please refer to the 2-/4-/6-/8- channel audio setup steps for
detailed software configuration information.
1-7 Connectors Introduction
1 3
2
6
5
11
18
12 13 17
4
1916
1) ATX_12V
2) ATX (Power Connector)
3) CPU_FAN
4) SYS_FAN
5) IDE
6) FDD
7) SATAII0 / 1 / 2 / 3
8) GSATAII0/1
9) PWR_LED
10) F_PANEL
GA-965GM-(D)S2 Motherboard - 18 -
10
9
7
81415
11) F_AUDIO
12) CD_IN
13) SPDIF_IO
14) F_USB1 / F_USB2 / F_USB3
15) F1_1394 / F2_1394
16) COMB
17) CI
18) CLR_CMOS
19) BATTERY
1/2) ATX_12V/ATX (Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, please make sure that all components and devices are properly installed. Align the power connector with its proper location on the motherboard and connect tightly. The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V power connector is not connected, the system will not start. Caution! Please use a power supply that is able to handle the system voltage requirements. It is recommended that a power supply that can withstand high power consumption be used (300W or greater). If a power supply is used that does not provide the required power, the result can lead to an unstable system or a system that is unable to start. If you use a 24-pin ATX power supply, please remove the small cover on the power connector on the motherboard before plugging in the power cord; otherwise, please do not remove it.
Pin No. Definition
1 GND
2
4
1
3
2 GND
3 +12V
4 +12V
English
12
1
24
13
Pin No. Definition
1 3.3V
2 3.3V
3 GND
4 +5V
5 GND
6 +5V
7 GND
8 Power Good
9 5V SB(stand by +5V)
10 +12V
11 +12V(Only for 24-pin ATX)
12 3.3V(Only for 24-pin ATX)
Pin No. Definition
13 3.3V
14 -12V
15 GND
16 PS_ON(soft On/Off)
17 GND
18 GND
19 GND
20 -5V
21 +5V
22 +5V
23 +5V (Only for 24-pin ATX)
24 GND(Only for 24-pin ATX)
Hardware Installation- 19 -
English
3/4) CPU_FAN / SYS_FAN (Cooler Fan Power Connector)
The cooler fan power connector supplies a +12V power voltage via a 4-pin power connector and possesses a foolproof connection design. Most coolers are designed with color-coded power connector wires. A red power connector wire indicates a positive connection and requires a +12V power voltage. The black connector wire is the ground wire (GND). Remember to connect the CPU/system fan cable to the CPU_FAN/SYS_FAN connector to prevent CPU damage or system hanging caused by overheating.
1
Pin No. Definition
1 GND
2 +12V/Speed Control
3 Sense
4 Speed Control
5) IDE (IDE Connector)
An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If you wish to connect two IDE devices, please set the jumper on one IDE device as Master and the other as Slave (for information on settings, please refer to the instructions located on the IDE device). Before attaching the IDE cable, please take note of the foolproof groove in the IDE connector.
40
39
GA-965GM-(D)S2 Motherboard - 20 -
2
1
6) FDD (FDD Connector)
The FDD connector is used to connect the FDD cable while the other end of the cable connects to the FDD drive. The types of FDD drives supported are: 360 KB, 720 KB, 1.2 MB, 1.44 MB and
2.88 MB. Before attaching the FDD cable, please take note of the foolproof groove in the FDD connector.
3334
12
7) SATAII0 / 1 / 2 / 3 (SATA 3Gb/s Connector, Controlled by Intel ICH8)
SATA 3Gb/s can provide up to 300 MB/s transfer rate. Please refer to the BIOS setting for the SATA 3Gb/s and install the proper driver in order to work properly.
English
SATAII2
7
1
SATAII3
Pin No. Definition
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
SATAII0
7
1
7
1
1
7
SATAII1
Hardware Installation- 21 -
English
8) GSATAII0/1 (SATA 3Gb/s Connector, Controlled by GIGABYTE SATA2)
SATA 3Gb/s can provide up to 300 MB/s transfer rate. Please refer to the BIOS setting for the SATA 3Gb/s and install the proper driver in order to work properly.
GSATAII0
7
1
GSATAII1
1
7
Pin No. Definition
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
9) PWR_LED
The PWR_LED connector is connected with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode(S1).
Pin No. Definition
1 MPD+
1
2 MPD-
3 MPD-
GA-965GM-(D)S2 Motherboard - 22 -
10) F_PANEL (Front Panel Jumper)
Please connect the power LED, PC speaker, reset switch and power switch etc of your chassis front panel to the F_PANEL connector according to the pin assignment below.
Speaker Connector
Power Switch
Message LED/
Power/
Sleep LED
HD (IDE Hard Disk Active LED) Pin 1: LED anode(+)
Pin 2: LED cathode(-)
SPEAK (Speaker Connector) Pin 1: Power
Pin 2- Pin 3: NC
Pin 4: Data(-)
RES (Reset Switch) Open: Normal
Close: Reset Hardware System
PW (Power Switch) Open: Normal
Close: Power On/Off
MSG (Message LED/Power/Sleep LED) Pin 1: LED anode(+)
Pin 2: LED cathode(-)
NC NC
SPEAK-
SPEAK+
PW+
MSG+
PW-
MSG-
1920
Reset Switch
NC
RES+
RES-
HD-
HD+
1
2
IDE Hard Disk
English
Active LED
Hardware Installation- 23 -
English
11) F_AUDIO (Front Audio Connector)
This connector supports either HD (High Definition) or AC97 front panel audio module. If you wish to use the front audio function, connect the front panel audio module to this connector. Check the pin assignments carefully while you connect the front panel audio module. Incorrect connection between the module and connector will make the audio device unable to work or even damage it. For optional front panel audio module, please contact your chassis manufacturer.
910
12
HD Audio:
Pin No. Definition
1 MIC2_L
2 GND
3 MIC2_R
4 -ACZ_DET
5 LINE2_R
6 FSENSE1
7 FAUDIO_JD
8 No Pin
9 LINE2_L
10 FSENSE2
AC'97 Audio:
Pin No. Definition
1 MIC
2 GND
3 MIC Power
4NC
5 Line Out (R)
6NC
7NC
8 No Pin
9 Line Out (L)
10 NC
By default, the audio driver is configured to support HD Audio. To connect an AC97 front panel audio module to this connector, please refer to the instructions on Page 80 about the software settings.
GA-965GM-(D)S2 Motherboard - 24 -
12) CD_IN (CD In Connector)
Connect CD-ROM or DVD-ROM audio out to the connector.
Pin No. Definition
1 CD-L
1
2 GND
3 GND
4 CD-R
13) SPDIF_IO (SPDIF In/Out Connector)
The SPDIF output is capable of providing digital audio to external speakers or compressed AC3 data to an external Dolby Digital Decoder. Use this feature only when your stereo system has digital input function. Use SPDIF IN feature only when your device has digital output function. Be careful with the polarity of the SPDIF_IO connector. Check the pin assignment carefully while you connect the SPDIF cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional SPDIF cable, please contact your local dealer.
English
2
6
1
5
Pin No. Definition
1 Power
2 No Pin
3 SPDIF
4 SPDIFI
5 GND
6 GND
Hardware Installation- 25 -
English
14) F_USB1 / F_USB2 / F_USB3 (Front USB Connectors)
Be careful with the polarity of the front USB connector. Check the pin assignment carefully while you connect the front USB cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional front USB cable, please contact your local dealer.
Pin No. Definition
1 Power (5V)
2 Power (5V)
1
9
2
10
3 USB DX-
4 USB Dy-
5 USB DX+
6 USB Dy+
7 GND
8 GND
9 No Pin
10 NC
15) F1_1394 / F2_1394 (IEEE 1394 Connector)
Serial interface standard set by Institute of Electrical and Electronics Engineers, which has features like high speed, highbandwidth and hot plug. Be careful with the polarity of the IEEE 1394 connector. Check the pin assignment carefully while you connect the IEEE 1394 cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional IEEE 1394 cable, please contact your local dealer.
10
GA-965GM-(D)S2 Motherboard - 26 -
Pin No. Definition
1TPA+
2TPA-
3 GND
1
9
2
4 GND
5 TPB+
6 TPB-
7 Power (12V)
8 Power (12V)
9 No Pin
10 GND
16) COMB (COMB Connector)
Be careful with the polarity of the COMB connector. Check the pin assignments while you connect the COMB cable. Please contact your nearest dealer for optional COMB cable.
Pin No. Definition
1 NDCDB-
2 NSINB
3 NSOUTB
4 NDTRB-
10
2
1
9
5 GND
6 NDSRB-
7 NRTSB-
8 NCTSB-
9 NRIB-
10 No Pin
17) CI (Chassis Intrusion, Case Open)
This 2-pin connector allows your system to detect if the chassis cover is removed. You can check the "Case Opened" status in BIOS Setup.
English
Pin No. Definition
1
1 Signal
2 GND
Hardware Installation- 27 -
Loading...
+ 61 hidden pages