GIGABYTE GA-8I865GMF-775 User Manual [ru]

GA-8I865GM-775 / GA-8I865GMF-775

Intel® Pentium® 4 LGA775 Processor Motherboard

User's Manual

Rev. 1001

12ME-8I865GMT-1001

GA-8I865GM-775 / GA-8I865GMF-775

Sep. 5, 2004

GA-8I865GM-775 /

GA-8I865GMF-775

Motherboard

The trademarks mentioned in the manual are legally registered to their respective companies.

Notice

The written content provided with this product is the property of Gigabyte.

No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any

means without Gigabyte's prior written permission. Specifications and features are subject to

change without prior notice.

Product Manual Classification

In order to assist in the use of this product, Gigabyte has categorized the user manual in the

following:

 For detailed product information and specifications, please carefully read the

"Product User Manual".

 For detailed information related to Gigabyte's unique features, please go to Gigabyte's

website under "Technology Guide" where information can be downloaded in .pdf format.

Fore more product details, please click onto Gigabyte's website at www.gigabyte.com.tw

Table of Contents

GA-8I865GM-775/GA-8I865GMF-775 Motherboard Layout ......................................... 6

Block Diagram ............................................................................................................... 7

Chapter 1 Hardware Installation ................................................................................... 9

1-1 Considerations Prior to Installation ................................................................. 9

1-2 Feature Summary .......................................................................................... 10

1-3 Installation of the CPU and Heatsink ............................................................ 11

1-3-1 Installation of the CPU .......................................................................................... 11

1-3-2 Installation of the Heatsink ................................................................................... 12

1-4 Installation of Memory ................................................................................... 13

1-5 Installation of Expansion Cards .................................................................... 15

1-6 I/O Back Panel Introduction .......................................................................... 16

1-7 Connectors Introduction ................................................................................ 17

Chapter 2 BIOS Setup ............................................................................................... 27

The Main Menu (For example: BIOS Ver. : E4) ....................................................... 28

2-1 Standard CMOS Features ............................................................................. 30

2-2 Advanced BIOS Features ............................................................................. 32

2-3 Integrated Peripherals ................................................................................... 34

2-4 Power Management Setup ............................................................................ 37

2-5 PnP/PCI Configurations ................................................................................ 38

2-6 PC Health Status ........................................................................................... 39

2-7 Frequency/Voltage Control ........................................................................... 40

2-8 Load Fail-Safe Defaults ................................................................................ 41

2-9 Load Optimized Defaults ............................................................................... 41

2-10 Set Supervisor/User Password ..................................................................... 42

2-11 Save & Exit Setup ......................................................................................... 43

2-12 Exit Without Saving ....................................................................................... 43

- 4 -

Chapter 3 Drivers Installation ..................................................................................... 45

3-1 Install Chipset Drivers ................................................................................... 45

3-2 Software Application ...................................................................................... 46

3-3 Software Information ..................................................................................... 46

3-4 Hardware Information .................................................................................... 47

3-5 Contact Us ..................................................................................................... 47

Chapter 4 Appendix ................................................................................................... 49

4-1 Unique Software Utilities ............................................................................... 49

4-1-1 Xpress Recovery Introduction .............................................................................. 49

4-1-2 Flash BIOS Method Introduction .......................................................................... 52

4-1-3 2- / 4- / 5.1- Channel Audio Function Introduction .............................................. 61

4-2 Troubleshooting............................................................................................. 65

- 5 -

GA-8I865GM-775/GA-8I865GMF-775 Motherboard Layout

KB_MS

VGA

R_USB

USB

AUDIO

CODEC

COMA

Marvell 8001

LPT

SPDIF

CD_IN

LAN

ATX_12V

F_AUDIO

BIOS

LPC47M997

AGP

COMB

LGA775

F2_1394*

Intel 865G

F1_1394*

PCI1

PCI2

PCI3

CPU_FAN

TSB43AB23*

ATX

FDD

IDE2

IDE1

GA-8I865GM-775 (or GA-8I865GMF-775*)

DDR3

BAT

DDR4

SATA1

SATA0

PWR_LED

F_PANEL

CLR_CMOS

SYS_FAN

DDR1

F_USB1

DDR2

Intel ICH5

F_USB2

* Only for GA-8I865GMF-775.

- 6 -

Block Diagram

AGPCLK

(66MHz)

AGP 8X/4X

PCI Bus

TSB43AB23*

3 IEEE1394*

VGA

Marvell

8001

RJ45

LGA775

Processor

CODEC

Intel

865G

GMCH

Intel

ICH5

Host

Interface

CPUCLK+/-(133/200MHz)

DDR 400/333/266MHz DIMM

Dual Channel Memory

HCLK (133/200MHz)

GMCHCLK (66MHz)

66MHz 33MHz

14.318MHz 48MHz

BIOS

2 Serial ATA

ATA33/66/100 IDE Channels

LPC47M997

Floppy

LPT Port

COM Port

3 PCI

PCICLK

(33MHz)

* Only for GA-8I865GMF-775.

MIC

Line-Out

Line-In

- 7 -

8 USB

Ports

14.318MHz

33MHz

PS/2 KB/Mouse

- 8 -

Chapter 1Hardware Installation

1-1 Considerations Prior to Installation

Preparing Your Computer

The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please follow the instructions below:

1. Please turn off the computer and unplug its power cord.

2. When handling the motherboard, avoid touching any metal leads or connectors.

3. It is best to wear an electrostatic discharge (ESD) cuff when handling electronic components (CPU, RAM).

4. Prior to installing the electronic components, please have these items on top of an antistatic pad or within a electrostatic shielding container.

5. Please verify that you the power supply is switched off before unplugging the power supply connector from the motherboard.

Installation Notices

1. Prior to installation, please do not remove the stickers on the motherboard. These stickers are required for warranty validation.

2. Prior to the installation of the motherboard or any hardware, please first carefully read the information in the provided manual.

3. Before using the product, please verify that all cables and power connectors are connected.

4. To prevent damage to the motherboard, please do not allow screws to come in contact with the motherboard circuit or its components.

5. Please make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing.

6. Please do not place the computer system on an uneven surface.

7. Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user.

8. If you are uncertain about any installation steps or have a problem related to the use of the product, please consult a certified computer technician.

English

Instances of Non-Warranty

1. Damage due to natural disaster, accident or human cause.

2. Damage as a result of violating the conditions recommended in the user manual.

3. Damage due to improper installation.

4. Damage due to use of uncertified components.

5. Damage due to use exceeding the permitted parameters.

6. Product determined to be an unofficial Gigabyte product.

Hardware Installation- 9 -

English

1-2 Feature Summary

Motherboard  GA-8I865GM-775 or GA-8I865GMF-775 CPU  Supports the latest Intel® Pentium® 4 LGA775 CPU

 Supports 800/533MHz FSB  L2 cache varies with CPU

Chipset  Northbridge: Intel® 865G Chipset

 Southbridge: Intel® ICH5

Memory  4 DDR DIMM memory slots (supports up to 4GB memory)

 Supports dual channel DDR 400/333/266 unbrffered DIMM  Supports 2.5V DDR DIMM

Slots  1 AGP slot supports 8X/4X(1.5V) mode

 3 PCI slots

IDE Connections  2 IDE connection (UDMA 33/ATA 66/ATA 100), allows connection of

4 IDE devices FDD Connections  1 FDD connection, allows connection of 2 FDD devices Onboard SATA  2 Serial ATA ports from ICH5 controller (SATA0, SATA1) Peripherals  1 parallel port supporting Normal/EPP/ECP mode

 2 serial ports (COMA, onboard COMB)  8 USB 2.0/1.1 ports (rear x 4, front x 4 via cable)  3 IEEE1394 ports* (requires cable)  1 front audio connector  1 IR connector  1 PS/2 keyboard port  1 PS/2 mouse port

Onboard LAN  Onboard Marvell 8001 chip (10/100/1000 Mbit)

 1 RJ 45 port

Onboard Audio  ADI AD1888 CODEC

 Supports 2 / 4 / 6 channel audio  Supports Line In (Rear Speaker Out) ; Line Out (Front Speaker Out) ;

MIC (Center/Subwoofer Speaker Out)

 SPDIF Out connection  CD In connection

I/O Control  SMSC LPC47M997 Hardware Monitor  System voltage detection

 CPU / System temperature detection  CPU / System fan speed detection

BIOS  Use of licensed AWARD BIOS

 Supports Q-Flash

Additional Features  Supports @BIOS Form Factor  Micro ATX form factor; 24.4cm x 24.4cm

(Note)

(Note) Due to standard PC architecture, a certain amount of memory is reserved for system usage and

therefore the actual memory size is less than the stated amount. For example, 4 GB of memory size will instead be shown as 3.xxGB memory during system startup.

* Only for GA-8I865GMF-775.

GA-8I865GM(F)-775 Motherboard - 10 -

1-3 Installation of the CPU and Heatsink

Before installing the CPU, please comply with the following conditions:

1. Please make sure that the motherboard supports the CPU.

2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong direction, the CPU will not insert properly. If this occurs, please change the insert direction of the CPU.

3. Please add an even layer of heat sink paste between the CPU and heatsink.

4. Please make sure the heatsink is installed on the CPU prior to system use, otherwise overheating and permanent damage of the CPU may occur.

5. Please set the CPU host frequency in accordance with the processor specifications. It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the required standards for the peripherals. If you wish to set the frequency beyond the proper specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc.

HT functionality requirement content :

Enabling the functionality of Hyper-Threading Technology for your computer system requires all of the following platform components:

- CPU: An Intel® Pentium 4 Processor with HT Technology

- Chipset: An Intel® Chipset that supports HT Technology

- BIOS: A BIOS that supports HT Technology and has it enabled

- OS: An operation system that has optimizations for HT Technology

1-3-1 Installation of the CPU

Metal Lever

Fig. 1 Gently lift the metal lever located on the CPU socket to the upright position.

English

Fig. 2 Remove the plastic covering on the CPU socket.

Fig. 3 Notice the small gold colored triangle located on the edge of the CPU socket. Align the indented corner of the

CPU with the triangle and gently insert the CPU into position. (Grasping the CPU firmly between your thumb and forefinger, carefully place it into the socket in a straight and downwards motion. Avoid twisting or bending motions that might cause damage to the CPU during installation.)

Fig. 4 Once the CPU is properly inserted, please replace the plastic covering and push the metal lever back into its original position.

Hardware Installation- 11 -

1-3-2 Installation of the Heatsink

Male Push Pin

English

Fig.1 Please apply an even layer of heatsink paste on the surface of the installed CPU.

Fig. 3 Place the heatsink atop the CPU and make sure the push pins aim to the pin hole on the motherboard. Pressing down the push pins diagonally.

The top of Female Push Pin

Female Push Pin

Fig. 2 (Turning the push pin along the direction of arrow is to remove the heatsink, on the contrary, is to install.) Please note the direction of arrow sign on the male push pin doesn't face inwards before installation. (This instruction is only for Intel boxed fan)

Fig. 4 Please make sure the Male and Female push pin are joined closely. (for detailed installation instructions, please refer to the heatsink installation section of the user manual)

Fig. 5 Please check the back of motherboard after installing. If the push pin is inserted as the picture, the installation is complete.

The heatsink may adhere to the CPU as a result of hardening of the heatsink paste. To prevent such an occurrence, it is suggested that either thermal tape rather than heat sink paste be used for heat dissipation or using extreme care when removing the heatsink.

GA-8I865GM(F)-775 Motherboard - 12 -

Fig. 6 Finally, please attach the power connector of the heatsink to the CPU fan header located on the motherboard.

1-4 Installation of Memory

Before installing the memory modules, please comply with the following conditions:

1. Please make sure that the memory used is supported by the motherboard. It is recommended that memory of similar capacity, specifications and brand be used.

2. Before installing or removing memory modules, please make sure that the computer power is switched off to prevent hardware damage.

3. Memory modules have a foolproof insertion design. A memory module can be installed in only one direction. If you are unable to insert the module, please switch the direction.

The motherboard supports DDR II memory modules, whereby BIOS will automatically detect memory capacity and specifications. Memory modules are designed so that they can be inserted only in one direction. The memory capacity used can differ with each slot.

Notch

DDR

Fig.1 The DIMM socket has a notch, so the DIMM memory module can only fit in one direction. Insert the DIMM memory module vertically into the DIMM socket. Then push it down.

English

Fig.2 Close the plastic clip at both edges of the DIMM sockets to lock the DIMM module. Reverse the installation steps when you wish to remove the DIMM module.

Hardware Installation- 13 -

English

Dual Channel DDR

GA-8I865GM-775 / GA-8I865GMF-775 supports the Dual Channel Technology. After operating the Dual Channel Technology, the bandwidth of Memory Bus will add double up to 6.4GB/s(DDR400).

GA-8I865GM-775 / GA-8I865GMF-775 includes 4 DIMM sockets, and each Channel has two DIMM sockets as following:

Channel A : DDR 1, DDR 2

Channel B : DDR 3, DDR 4 If you want to operate the Dual Channel Technology, please note the following explanations due to the limitation of Intel chipset specifications.

1. Dual channel memory cannot be used if one or three DDR memory modules are installed.

2. If two DDR memory modules are installed (same storage capacity), one must be added to the Channel A slot and the other in the Channel B slot in order to use dual channel memory. Dual channel memory cannot function if both DDR memory modules are installed on the same channel.

3. If four DDR memory modules are installed, please use memory of the same storage capacity in order to use dual channel memory and for BIOS to detect all the DDR memory modules.

We'll strongly recommend our user to slot two DDR memory modules into the DIMMs with the same color in order for Dual Channel Technology to work.

The following table is for Dual Channel Technology combination: (DS: Double Side, SS: Single Side)

DDR 1 DDR 2 DDR 3 DDR 4

2 memory modules

4 memory modules

DS/SS X DS/SS X

X DS/SS X DS/SS

DS/SS DS/SS DS/SS DS/SS

GA-8I865GM(F)-775 Motherboard - 14 -

1-5 Installation of Expansion Cards

You can install your expansion card by following the steps outlined below:

1. Read the related expansion card's instruction document before install the expansion card into the computer.

2. Remove your computer's chassis cover, screws and slot bracket from the computer.

3. Press the expansion card firmly into expansion slot in motherboard.

4. Be sure the metal contacts on the card are indeed seated in the slot.

5. Replace the screw to secure the slot bracket of the expansion card.

6. Replace your computer's chassis cover.

7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.

8. Install related driver from the operating system.

Installing a AGP VGA card:

Please carefully pull out the small whitedrawable bar at the end of the AGP slot when you try to install/uninstall the VGA card. Please align the VGA card to the onboard AGP slot and press firmly down on the slot. Make sure your VGA card is locked by the small white-drawable bar.

English

Hardware Installation- 15 -

English

1-6 I/O Back Panel Introduction

PS/2 Keyboard and PS/2 Mouse Connector

To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the lower port (purple).

Parallel Port

The parallel port allows connection of a printer, scanner and other peripheral devices.

COM A (Serial Port)

Connects to serial-based mouse or data processing devices.

VGA Port

Monitor can be connected to VGA port.

USB port

Before you connect your device(s) into USB connector(s), please make sure your device(s) such as USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface. Also make sure your OS supports USB controller. If your OS does not support USB controller, please contact OS ven dor for possible patch or driver upgrade. For more information please contact your OS or device(s) vendors.

LAN Port

The provided Internet connection is Gigabit Ethernet, providing data transfer speeds of 10/100/1000Mbps.

Line In

Devices like CD-ROM, walkman etc. can be connected to Line In jack.

Line Out

Connect the stereo speakers or earphone to this connector.

MIC In

Microphone can be connected to MIC In jack.

You can use audio software to configure 2-/4-/6-channel audio functioning.

GA-8I865GM(F)-775 Motherboard - 16 -

1-7 Connectors Introduction

English

11 13

1) ATX_12V

2) ATX (Power Connector)

3) CPU_FAN

4) SYS_FAN

5) FDD

6) IDE1 / IDE2

7) SATA0 / SATA1

8) PWR_LED

9) BAT

12 16

9 18

10) F_PANEL

11) F_AUDIO

12) CD_IN

13) SPDIF

14) F_USB1 / F_USB2

15) F1_1394* / F2_1394*

16) COMB

17) IR

18) CLR_CMOS

* Only for GA-8I865GMF-775.

Hardware Installation- 17 -

English

1/2) ATX_12V/ATX (Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, please make sure that all components and devices are properly installed. Align the power connector with its proper location on the motherboard and connect tightly. The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V power connector is not connected, the system will not start. Caution! Please use a power supply that is able to handle the system voltage requirements. It is recommended that a power supply that can withstand high power consumption be used (300W or greater). If a power supply is used that does not provide the required power, the result can lead to an unstable system or a system that is unable to start. Please remove the sticker on the motherboard before plugging in while the ATX power supplier is 24 pins; Otherwise, please do not remove it.

Pin No. Definition

1 GND

2 GND

3 +12V

4 +12V

Pin No. Definition

1 3.3V

2 3.3V

3 GND

4 VCC

5 GND

6 VCC

7 GND

8 Power Good

9 5V SB(stand by +5V)

10 +12V

11 +12V

12 3.3V(Only for 24pins ATX)

13 3.3V

14 -12V

15 GND

16 PS_ON(soft On/Off)

17 GND

18 GND

19 GND

20 -5V

21 VCC

22 VCC

23 VCC

24 GND

GA-8I865GM(F)-775 Motherboard - 18 -

3/4) CPU_FAN / SYS_FAN (Cooler Fan Power Connector)

The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin(only for CPU_FAN) power connector and possesses a foolproof connection design. Most coolers are designed with color-coded power connector wires. A red power connector wire indicates a positive connection and requires a +12V power voltage. The black connector wire is the ground wire (GND). Please remember to connect the power to the cooler to prevent system overheating and failure. Caution! Please remember to connect the power to the CPU fan to prevent CPU overheating and failure.

Pin No. Definition

CPU_FAN

SYS_FAN

1 GND

2 +12V

3 Sense

4 Speed Control

(Only for CPU_FAN)

5) FDD (FDD Connector)

The FDD connector is used to connect the FDD cable while the other end of the cable connects to the FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB. Please connect the red power connector wire to the pin1 position.

English

Hardware Installation- 19 -

English

6) IDE1 / IDE2 (IDE Connector)

An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If you wish to connect two IDE devices, please set the jumper on one IDE device as Master and the other as Slave (for information on settings, please refer to the instructions located on the IDE device).

7) SATA0 / SATA1 (Serial ATA Connector)

Serial ATA can provide 150MB/s transfer rate. Please refer to the BIOS setting for the Serial ATA and install the proper driver in order to work properly.

Pin No. Definition

1 GND

2 TXP

3 TXN

4 GND

5 RXN

6 RXP

7 GND

GA-8I865GM(F)-775 Motherboard - 20 -

8) PWR_LED

PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode.

Pin No. Definition

1 MPD+

2 MPD-

3 MPD-

9) BAT(Battery)

English

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended

by the manufacturer.

Dispose of used batteries according to the manufacturer's

instructions.

If you want to erase CMOS...

1. Turn OFF the computer and unplug the power cord.

2. Remove the battery, wait for 30 second.

3. Re-install the battery.

4. Plug the power cord and turn ON the computer.

Hardware Installation- 21 -

English

10) F_PANEL (Front Panel Jumper)

Please connect the power LED, PC peaker, reset switch and power switch etc. of your chassis front panel to the F_PANEL connector according to the pin assignment below.

Message LED/

Power/

Sleep LED

2 1

HD (IDE Hard Disk Active LED) Pin 1: LED anode(+)

Pin 2: LED cathode(-)

SPEAK (Speaker Connector) Pin 1: VCC(+)

Pin 2- Pin 3: NC

Pin 4: Data(-)

RES (Reset Switch) Open: Normal Operation

Close: Reset Hardware System

PW (Power Switch) Open: Normal Operation

Close: Power On/Off

MSG (Message LED/Power/Sleep LED) Pin 1: LED anode(+)

Pin 2: LED cathode(-)

NC NC

MSG+

HD+

IDE Hard Disk Active LED

Power Switch

PW+

PW-

MSG-

HD-

RES+

RES-

Reset Switch

Speaker Connector

SPEAK+

SPEAK-

20 19

GA-8I865GM(F)-775 Motherboard - 22 -

+ 50 hidden pages