Gigabyte GA-8I865GME-775-RH User Manual

GA-8I865GME-775-RH

Intel® Core

2 Extreme dual-core / Core

2 Duo /

(rev. 2.0)

Intel® Pentium® D / Pentium® 4 / Intel® Celeron® D LGA775 Processor Motherboard

User's Manual

Rev. 2002 12ME-865GMETR-2002R

* The WEEE marking on the product indicates this product must not be disposed of with user's other household waste

and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!

* The WEEE marking applies only in European Union's member states.

Dec. 29, 2006

GA-8I865GME-775-RH

Motherboard

Dec. 29, 2006

Motherboard

GA-8I865GME-775-RH

The trademarks mentioned in the manual are legally registered to their respective companies.

Notice

The written content provided with this product is the property of Gigabyte.

No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any

means without Gigabyte's prior written permission. Specifications and features are subject to

change without prior notice.

Product Manual Classification

In order to assist in the use of this product, Gigabyte has categorized the user manual in the

following:

 For detailed product information and specifications, please carefully read the

"User’s Manual."

 For detailed information related to Gigabyte's unique features, please go to the "Technology

Guide" section on Gigabyte’s website to read or download the information you need.

For more product details, please visit Gigabyte's website at www.gigabyte.com.tw

Table of Contents

Item Checklist ................................................................................................................. 6

Optional Accessories ...................................................................................................... 6

GA-8I865GME-775-RH (rev. 2.0) Motherboard Layout ................................................. 7

Block Diagram ................................................................................................................ 8

Chapter 1 Hardware Installation ..................................................................................... 9

1-1 Considerations Prior to Installation .................................................................... 9

1-2 Feature Summary .......................................................................................... 10

1-3 Installation of the CPU and CPU Cooler ....................................................... 12

1-3-1 Installation of the CPU ......................................................................................... 12

1-3-2 Installation of the CPU Cooler ............................................................................ 13

1-4 Installation of Memory .................................................................................... 14

1-5 Installation of Expansion Cards ...................................................................... 16

1-6 I/O Back Panel Introduction ........................................................................... 17

1-7 Connectors Introduction .................................................................................. 18

Chapter 2 BIOS Setup ................................................................................................ 27

The Main Menu (For example: BIOS Ver. : DM) ...................................................... 28

2-1 Standard CMOS Features ............................................................................. 30

2-2 Advanced BIOS Features .............................................................................. 32

2-3 Integrated Peripherals ..................................................................................... 34

2-4 Power Management Setup ............................................................................. 37

2-5 PnP/PCI Configurations ................................................................................. 39

2-6 PC Health Status ........................................................................................... 40

2-7 Frequency/Voltage Control ............................................................................. 42

2-8 Load Fail-Safe Defaults ................................................................................... 44

2-9 Load Optimized Defaults ................................................................................. 44

2-10 Set Supervisor/User Password ..................................................................... 45

2-11 Save & Exit Setup......................................................................................... 46

2-12 Exit Without Saving ....................................................................................... 46

- 4 -

Chapter 3 Drivers Installation ...................................................................................... 47

3-1 Install Chipset Drivers .................................................................................... 47

3-2 Software Applications ..................................................................................... 48

3-3 Driver CD Information .................................................................................... 48

3-4 Hardware Information ..................................................................................... 49

3-5 Contact Us ..................................................................................................... 49

Chapter 4 Appendix ................................................................................................... 51

4-1 Unique Software Utilities ................................................................................ 51

4-1-1 EasyTune 5 Introduction ..................................................................................... 51

4-1-2 Xpress Recovery2 Introduction ......................................................................... 52

4-1-3 Flash BIOS Method Introduction ........................................................................ 54

4-1-4 2 / 4 / 6 Channel Audio Function Introduction ................................................. 58

4-2 Troubleshooting ............................................................................................... 61

- 5 -

Item Checklist

IDE Cable x 1 and FDD Cable x 1

Serial ATA Cable x 1

I/O Shield

* The items listed above are for reference only, and are subject to change without notice.

Optional Accessories

 2 Ports USB 2.0 Cable (Part Number: 12CR1-1UB030-51/R)

 4 Ports USB 2.0 Cable (Part Number: 12CR1-1UB030-21/R)

- 6 -

GA-8I865GME-775-RH (rev. 2.0) Motherboard Layout

KB_MS

COMA

VGA

R_USB

USB_LAN

AUDIO

CODEC

LPT

Intel 82562G

ATX_12V

F_AUDIO

BIOS

REV: 2.0

IT8718

PCI1

PCI2

PCI3

CD_IN

AGP

LGA775

FDD

Intel® 865G

SYS _FAN

F_USB1

CPU_FAN

GA-8I865GME-775-RH

DDR2

DDR1

SATA1

Intel® ICH5

F_USB2

PWR_LED

SATA0

BATTERY

F_PANEL

IDE2

ATX

IDE1

CLR_CMOS

- 7 -

Block Diagram

AGP CLK

(66 MHz)

3 PCI

PCI CLK

(33 MHz)

AGP 8X/4X

PCI Bus

VGA

Intel

82562G

RJ45

LGA775

Processor

Interface

Intel® 865G

Intel® ICH5

AC97 Link

AC97

CODEC

MIC

Line-Out

CPU CLK+/-(200/133 MHz)

Host

DDR 400/333/266 MHz DIMM

GMCH CLK (200/133 MHz)

BIOS

IT8718

Line-In

Dual Channel Memory

ATA33/66/100 IDE Channel

2 SATA

8 USB Ports

Floppy

LPT Port

COM Port

PS/2 KB/Mouse

- 8 -

Chapter 1 Hardware Installation

1-1 Considerations Prior to Installation

Preparing Your Computer

The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please follow the instructions below:

1. Please turn off the computer and unplug its power cord.

2. When handling the motherboard, avoid touching any metal leads or connectors.

3. It is best to wear an electrostatic discharge (ESD) cuff when handling electronic components (CPU, RAM).

4. Prior to installing the electronic components, please have these items on top of an antistatic pad or within a electrostatic shielding container.

5. Please verify that the power supply is switched off before unplugging the power supply connector from the motherboard.

Installation Notices

1. Prior to installation, please do not remove the stickers on the motherboard. These stickers are required for warranty validation.

2. Prior to the installation of the motherboard or any hardware, please first carefully read the information in the provided manual.

3. Before using the product, please verify that all cables and power connectors are connected.

4. To prevent damage to the motherboard, please do not allow screws to come in contact with the motherboard circuit or its components.

5. Please make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing.

6. Please do not place the computer system on an uneven surface.

7. Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user.

8. If you are uncertain about any installation steps or have a problem related to the use of the product, please consult a certified computer technician.

English

Instances of Non-Warranty

1. Damage due to natural disaster, accident or human cause.

2. Damage as a result of violating the conditions recommended in the user manual.

3. Damage due to improper installation.

4. Damage due to use of uncertified components.

5. Damage due to use exceeding the permitted parameters.

6. Product determined to be an unofficial Gigabyte product.

Hardware Installation- 9 -

English

1-2 Feature Summary

CPU  LGA775 for Intel® Core

Pentium® 4 / Celeron® D

 L2 cache varies with CPU Front Side Bus  Supports 800/533 MHz FSB Chipset  Northbridge: Intel® 865G

 Southbridge: Intel® ICH5 LAN  Onboard Intel 82562G chip (10/100 Mbit) Audio  Onboard Realtek ALC655 CODEC chip

 Supports 2 / 4 / 6 channel audio

 Supports CD In connection

Storage  Intel® ICH5 Southbrigde

- 1 FDD connector, allowing connection of 1 FDD device

- 2 IDE connectors with ATA-100/66/33 support, allowing connection of 4 IDE devices

- 2 SATA connectors, allowing connection of 2 SATA devices

O.S Support  Microsoft Windows 2000/XP Memory  2 DDR DIMM memory slots (supports up to 2 GB memory)

 Supports dual channel DDR400/333/266 DIMM  Supports 2.5V DDR DIMMs

Expanstion Slots  1 AGP slot 4X/8X

 3 PCI slots

Internal Connectors  1 20-pin ATX power connector

 1 4-pin ATX 12V power connector  1 floppy connector  2 IDE connectors  2 SATA connectors  1 CPU fan connector  1 system fan connector  1 front panel connector  1 front audio connector  1 CD In connector  2 USB 2.0/1.1 connectors for additional 4 ports by cables  1 Chassis Intrusion connector  1 power LED connector

2 Extreme dual-core / CoreTM 2 Duo / Pentium® D /

GA-8I865GME-775-RH (rev. 2.0) Motherboard - 10 -

Rear Panel I/O  1 PS/2 keyboard port

 1 PS/2 mouse port  1 parallel port  1 serial port  1 VGA port  4 USB 2.0/1.1 ports  1 RJ-45 port  3 audio jacks (Line In / Line Out / MIC In)

I/O Control  IT8718 chip Hardware Monitor  System voltage detection

 CPU temperature detection  CPU / System fan speed detection  CPU warning temperature  CPU / System fan failure warning  CPU smart fan control

BIOS  1 4 Mbit flash ROM

 Use of licensed AWARD BIOS

Additional Features  Supports @BIOS

 Supports Download Center  Supports Q-Flash  Supports EasyTune  Supports Xpress Install  Supports Xpress Recovery2  Supports Xpress BIOS Rescue

Bundle Software  Norton Internet Security (OEM version) Form Factor  Micro ATX form factor; 24.4cm x 21.2cm

(Note)

English

(Note) EasyTune functions may vary depending on different motherboards.

Hardware Installation- 11 -

English

1-3 Installation of the CPU and CPU Cooler

Before installing the CPU, please comply with the following conditions:

1. Please make sure that the motherboard supports the CPU.

2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong direction, the CPU will not insert properly. If this occurs, please change the insert direction of the CPU.

3. Please add an even layer of heat sink paste between the CPU and CPU cooler.

4. Please make sure the CPU cooler is installed on the CPU prior to system use, otherwise overheating and permanent damage of the CPU may occur.

5. Please set the CPU host frequency in accordance with the processor specifications. It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the required standards for the peripherals. If you wish to set the frequency beyond the proper specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc.

HT functionality requirement content :

Enabling the functionality of Hyper-Threading Technology for your computer system requires all of the following platform components:

- CPU: An Intel® Pentium 4 Processor with HT Technology

- Chipset: An Intel® Chipset that supports HT Technology

- BIOS: A BIOS that supports HT Technology and has it enabled

- OS: An operation system that has optimizations for HT Technology

1-3-1 Installation of the CPU

Metal Lever

Fig. 1 Gently lift the metal lever located on the CPU socket to the upright position.

Fig. 2 Remove the plastic covering on the CPU socket.

Fig. 3 Notice the small gold colored triangle located on the edge of the CPU socket. Align the indented corner of the

CPU with the triangle and gently insert the CPU into position. (Grasping the CPU firmly between your thumb and forefinger, carefully place it into the socket in a straight and downwards motion. Avoid twisting or bending motions that might cause damage to the CPU during installation.)

GA-8I865GME-775-RH (rev. 2.0) Motherboard - 12 -

Fig. 4 Once the CPU is properly inserted, please replace the load plate and push the metal lever back into its original position.

1-3-2 Installation of the CPU Cooler

English

Male Push Pin

The top of Female Push Pin

Female Push Pin

Fig.1 Please apply an even layer of CPU cooler paste on the surface of the installed CPU.

Fig. 3 Place the CPU cooler atop the CPU and make sure the push pins aim to the pin hole on the motherboard.Pressing down the push pins diagonally.

Fig. 5 Please check the back of motherboard after installing. If the push pin is inserted as the picture, the installation is complete.

Fig. 2 (Turning the push pin along the direction of arrow is to remove the CPU cooler, on the contrary, is to install.) Please note the direction of arrow sign on the male push pin doesn't face inwards before installation. (This instruction is only for Intel boxed fan)

Fig. 4 Please make sure the Male and Female push pin are joined closely. (for detailed installation instructions, please refer to the CPU cooler installation section of the user manual)

Fig. 6 Finally, please attach the power connector of the CPU cooler to the CPU fan header located on the motherboard.

The CPU cooler may adhere to the CPU as a result of hardening of the heat paste. To prevent such an occurrence, it is suggested that either thermal tape rather than heat paste be used for heat dissipation or using extreme care when removing the CPU cooler.

Hardware Installation- 13 -

English

1-4 Installation of Memory

Before installing the memory modules, please comply with the following conditions:

1. Please make sure that the memory used is supported by the motherboard. It is recommended that memory of similar capacity, specifications and brand be used.

2. Before installing or removing memory modules, please make sure that the computer power is switched off to prevent hardware damage.

3. Memory modules have a foolproof insertion design. A memory module can be installed in only one direction. If you are unable to insert the module, please switch the direction.

The motherboard supports DDR memory modules, whereby BIOS will automatically detect memory capacity and specifications. Memory modules are designed so that they can be inserted only in one direction. The memory capacity used can differ with each slot.

notch

DDR memory module

Fig.1 The DIMM socket has a notch, so the DIMM memory module can only fit in one direction. Insert the DIMM memory module vertically into the DIMM socket. Then push it down.

Fig.2 Close the plastic clip at both edges of the DIMM sockets to lock the DIMM module. Reverse the installation steps when you wish to remove the DIMM module.

GA-8I865GME-775-RH (rev. 2.0) Motherboard - 14 -

Fig. 1

Fig. 2

Dual Channel Memory Configuration

The GA-8I865GME-775-RH supports the Dual Channel Technology. After operating the Dual Channel Technology, the bandwidth of memory bus will double.

The GA-8I865GME-775-RH includes 2 DIMM sockets. If you want to operate the Dual Channel Technology, please note the following explanations due to the limitation of Intel chipset specifications.

1. Dual Channel mode will not be enabled if only one DDR memory module is installed.

2. To enable Dual Channel mode with two memory modules (it is recommended to use memory modules of identical brand, size, chips, and speed), you must install them into DDR1 and DDR2 memory sockets.

English

Hardware Installation- 15 -

English

1-5 Installation of Expansion Cards

You can install your expansion card by following the steps outlined below:

1. Read the related expansion card's instruction document before installing the expansion card into the computer.

2. Remove your computer's chassis cover, screws and slot bracket from the computer.

3. Press the expansion card firmly into expansion slot in motherboard.

4. Be sure the metal contacts on the card are indeed seated in the slot.

5. Replace the screw to secure the slot bracket of the expansion card.

6. Replace your computer's chassis cover.

7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.

8. Install related driver from the operating system.

Installing a AGP expansion card:

Please carefully pull out the small whitedrawable bar at the end of the AGP slot when you try to install/uninstall the VGA card. Please align the VGA card to the onboard AGP slot and press firmly down on the slot. Make sure your VGA card is locked by the small white-drawable bar.

GA-8I865GME-775-RH (rev. 2.0) Motherboard - 16 -

1-6 I/O Back Panel Introduction

PS/2 Keyboard and PS/2 Mouse Connector

To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the lower port (purple).

Parallel Port

The parallel port allows connection of a printer, scanner and other peripheral devices.

Serial Port

Connects to serial-based mouse or data processing devices.

VGA Port

Monitor can be connected to VGA port.

USB Port

Before you connect your device(s) into USB connector(s), please make sure your device(s) such as USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface. Also make sure your OS supports USB controller. If your OS does not support USB controller, please contact OS vendor for possible patch or driver upgrade. For more information please contact your OS or device(s) vendors.

LAN Port

The provided Internet connection is fast Ethernet , providing data transfer speeds of 10/100 Mbps.

Line In

Devices like CD-ROM, walkman etc. can be connected to Line In jack.

Line Out

Stereo speakers, earphone or front surround speakers can be connected to Line Out (Front Speaker Out) jack.

MIC In

Microphone must be connected to MIC In jack.

English

You can use audio software to configure 2-/4-/6- channel audio functioning.

Hardware Installation- 17 -

1-7 Connectors Introduction

English

1) ATX_12V

2) ATX (Power Connector)

3) CPU_FAN

4) SYS_FAN

5) IDE1 / IDE2

6) FDD

7) SATA0 / SATA1

8) F_PANEL

6 1249

9) PWR_LED

10) F_AUDIO

11) CD_IN

12) F_USB1 / F_USB2

13) C I

14) CLR_CMOS

15) BATTERY

GA-8I865GME-775-RH (rev. 2.0) Motherboard - 18 -

1/2) ATX_12V / ATX (Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, please make sure that all components and devices are properly installed. Align the power connector with its proper location on the motherboard and connect tightly. The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V power connector is not connected, the system will not start. Caution! Please use a power supply that is able to handle the system voltage requirements. It is recommended that a power supply that can withstand high power consumption be used (300W or greater). If a power supply is used that does not provide the required power, the result can lead to an unstable system or a system that is unable to start.

English

Pin No. Definition

1 GND

2 GND

3 +12V

4 +12V

Pin No. Definition

1 3.3V

2 3.3V

3 GND

4 +5V

5 GND

6 +5V

7 GND

8 Power Good

9 5V SB (stand by +5V)

10 +12V

11 3.3V

12 -12V

13 GND

14 PS_ON(soft on/off)

15 GND

16 GND

17 GND

18 -5V

19 +5V

20 +5V

Hardware Installation- 19 -

English

3/4) CPU_FAN / SYS_FAN (Cooler Fan Power Connector)

The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin(CPU_FAN) power connector and possesses a foolproof connection design. Most coolers are designed with color-coded power connector wires. A red power connector wire indicates a positive connection and requires a +12V power voltage. The black connector wire is the ground wire (GND). Remember to connect the CPU/system fan cable to the CPU_FAN/SYS_FAN connector to prevent CPU damage or system hanging caused by overheating.

CPU_FAN :

CPU_FAN

SYS_FAN

Pin No. Definition

1 GND

2 +12V / Speed Control

3 Sense

4 Speed Control

SYS_FAN :

Pin No. Definition

1 GND

2 +12V

3 Sense

5) IDE1 / IDE2 (IDE Connector)

An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If you wish to connect two IDE devices, please set the jumper on one IDE device as Master and the other as Slave (for information on settings, please refer to the instructions located on the IDE device).

GA-8I865GME-775-RH (rev. 2.0) Motherboard - 20 -

IDE2

IDE1

+ 44 hidden pages