Gigabyte GA-7ZMMC User Manual

				FCC Compliance Statement:
				This equipment has been tested and found to
	DECLARATION OF CONFORMITY
	Per FCC Part 2 Section 2. 1077(a)			comply with limits for a Class B digital device,
	Responsible Party Name: G.B.T. INC.			pursuant to Part 15 of the FCC rules. These
				limits are	designed	to	provide		reasonable
	Address: 18305 Valley Blvd., Suite#A
		LA Puent, CA 91744		protection	against	harmful		interference			in
	Phone/Fax No: [phone]/ [phone]
	hereby declares that the product			residential	installations.		This		equipment
	Product Name: Mother Board
				generates,	uses, and		can	radiate		radio
	Model Number: GA-7ZMMC
	Conforms to the following specifications:			frequency energy, and if not installed and used
	FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109(a),			in accordance with the instructions, may cause
	Class B Digital Device
	Supplementary Information:
				harmful interference		to radio		communications.
	This device complies with part 15 of the FCC Rules. Operation is subject to the
	following two conditions:	(1) This device may not cause harmful
	and (2) this device must accept any inference received, including			However, there is no guarantee that interference
	that may cause undesired operation.
	Representative Person's Name:	ERIC LU
				will not occur in a particular installation. If this
	Signature:	EricLu
	Date:	Jan. 15, 2001		equipment does cause interference to radio or
				television	equipment	reception, which				can	be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna

-Move the equipment away from the receiver

-Plug the equipment into an outlet on a circuit different from that to which the receiver is connected

-Consult the dealer or an experienced radio/television technician for additional suggestions

You are cautioned that any change or modifications to the equipment not expressly approve by the party responsible for compliance could void Your authority to operate such equipment.

This device complies with Part 15 of the FCC Rules. Operation is subjected to the following two conditions 1) this device may not cause harmful interference and 2) this device must accept any interference received, including interference that may cause undesired operation.

Declaration of Conformity

We, Manufacturer/Importer

(full address)

G.B.T. Technology Träding GMbH

Ausschlager Weg 41, 1F, 20537 Hamburg, Germany

declare that the product

( description of the apparatus, system, installation to which it refers)

Mother Board

GA-7ZMMC

is in conformity with

(reference to the specification under which conformity is declared) in accordance with 89/336 EEC-EMC Directive

EN 55011	Limits and methods of measurement
	of radio disturbance characteristics of
	industrial, scientific and medical (ISM
	high frequency equipment
EN55013	Limits and methods of measurement
	of radio disturbance characteristics of
	broadcast receivers and associated
	equipment
EN 55014	Limits and methods of measurement
	of radio disturbance characteristics of
	household electrical appliances,
	portable tools and similar electrical
	apparatus
EN 55015	Limits and methods of measurement
	of radio disturbance characteristics of
	fluorescent lamps and luminaries
EN 55020	Immunity from radio interference of
	broadcast receivers and associated
	equipment
EN 55022	Limits and methods of measurement
	of radio disturbance characteristics of
	information technology equipment
DIN VDE 0855	Cabled distribution systems; Equipment
part 10	for receiving and/or distribution from
part 12	sound and television signals

CE marking

EN 61000-3-2*	Disturbances in supply systems caused
EN60555-2	by household appliances and similar
	electrical equipment “Harmonics”
EN61000-3-3*	Disturbances in supply systems caused
EN60555-3	by household appliances and similar
	electrical equipment “Voltage fluctuations”
EN 50081-1	Generic emission standard Part 1:
	Residual, commercial and light industry
EN 50082-1	Generic immunity standard Part 1:
	Residual, commercial and light industry
EN 55081-2	Generic emission standard Part 2:
	Industrial environment
EN 55082-2	Generic immunity standard Part 2:
	Industrial environment
ENV 55104	Immunity requirements for household
	appliances tools and similar apparatus
EN 50091- 2	EMC requirements for uninterruptible
	power systems (UPS)

(EC conformity marking)

The manufacturer also declares the conformity of above mentioned product with the actual required safety standards in accordance with LVD 73/23 EEC

EN 60065	Safety requirements for mains operated	EN 60950	Safety for information technology equipment
	electronic and related apparatus for		including electrical business equipment
	household and similar general use
EN 60335	Safety of household and similar	EN 50091-1	General and Safety requirements for
	electrical appliances		uninterruptible power systems (UPS)
	Manufacturer/Importer
			Signature	:	Rex Lin
	(Stamp)	Date : Jan. 15, 2001	Name	:	Rex Lin

7ZMMC

AMD AthlonTM/DuronTM Socket A Processor

Motherboard

USER'S MANUAL

AMD AthlonTM/DuronTM Socket A Processor Motherboard

REV. 2.01 Third Edition

R-201-03-010627

1) Revision History

2) Item Checklist

3) Features

4) Hardware Setup

5) Performance & Block Diagram

6) Suspend to RAM

7) Four Speaker & SPDIF

8) @BIOSTM & EasyTuneIIITM

9) BIOS Setup

10) Appendix

How This Manual Is Organized

This manual is divided into the following sections:

Manual revision information

Product item list

Product information & specification

Instructions on setting up the motherboard

Product performance & block diagram

Instructions STR installation

Four Speaker & SPDIF introduction

@BIOSTM & EasyTuneIIITM introduction

Instructions on setting up the BIOS software

General reference

Table Of Content

Revision History	P.1
Item Checklist	P.2
Feature Summary	P.3
7ZMMC Motherboard Layout	P.5
Page Index for CPU Speed Setup / Connectors / Panel and Jumper	P.6
Definition
Performance List	P.23
Block Diagram	P.25
Suspend to RAM Installation	P.26
Four Speaker & SPDIF Introduction (Optional)	P.32
@BIOSTM Introduction	P.38
EasyTuneIIITM Introduction	P.39
Memory Installation	P.41
Page Index for BIOS Setup	P.42
Appendix	P.67

7ZMMC Motherboard

Revision History

Revision	Revision Note	Date
2.01	Initial release of the 7ZMMC motherboard user’s manual.	Feb. 2001
2.01	Second release of the 7ZMMC motherboard user’s	Apr. 2001
	manual.
2.01	Third release of the 7ZMMC motherboard user’s manual.	Jun. 2001

The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a commitment to update the information contained herein. Third-party brands and names are the property of their respective owners.

Jun. 27, 2001 Taipei, Taiwan, R.O.C

1

Item Checklist

Item Checklist

;The 7ZMMC motherboard

;Cable for IDE / floppy device

;Diskettes or CD (GA-7ZMM CD) for motherboard driver & utility

;7ZMMC user’s manual

2

7ZMMC Motherboard

Feature Summary

Form Factor	y	24.4 cm x 22.2 cm Micro ATX size form factor, 4 layers
CPU		PCB.
	y	AMD AthlonTM/DuronTM (K7) Socket A Processor
	y 256K/64K L2 cache on die
	y Supports 600MHz ~ 1GHz and above
Chipset	Pro Savage KM133, consisting of:
	y VT8365 Memory/AGP/PCI Controller (PAC)
	y VT82C686B PCI Super-I/O Integrated Peripheral
Clock Generator		Controller (PSIPC)
	y	ICS 9248BF-141
		100/102*/104*/106*/108*/110*/112*/133 MHz system bus
		speeds (* These speed settings are not guaranteed)
Memory	y	2 168-pin DIMM sockets
	y Supports PC-100/133 and VCM SDRAM
	y Supports up to 1.0GB DRAM
	y Supports only 3.3V SDRAM DIMM
I/O Control	y	VT82C686B
Slots	y	1 AGP slot supports 4X mode & AGP 2.0 compliant
	y 3 PCI slots supports 33MHz & PCI 2.2 compliant
	y 1 CNR (Communication and Networking Riser) slot
		(Not support LAN)
On-Board IDE	y	2 IDE bus master (UDMA 33/ATA 66/ATA 100) IDE ports
		for up to 4 ATAPI devices
	y Supports PIO mode 3, 4 (UDMA 33/ATA 66/ATA 100) IDE
		& ATAPI CD-ROM
On-Board	y	1 floppy port supports 2 FDD with 360K, 720K, 1.2M,
Peripherals		1.44M and 2.88M bytes
	y 1 parallel port supports Normal/EPP/ECP mode
	y 1 serial port (COM A)
	y	4 USB ports
Hardware Monitor	y	CPU/System fan revolution detection
	y	CPU/Power/System fan control
	y	System voltage detection
	y	CPU/System temperature detection

To be continued…

3

		Features Summary
PS/2 Connector	y	PS/2 Keyboard interface and PS/2 Mouse interface
On-Board VGA	y	Build S3 Savage4 (86C370) in VT8365
	y Support shared memory architecture
On-Board Sound	y	Creative CT5880 sound (Optional)
	y	AC’97 CODEC
	y Line In / Line Out / Mic In / AUX In / CD In / TEL /
		SPDIF (Optional) / Game Port /
		Four Speaker (Optional)
BIOS	y	Licensed AMI BIOS, 2M bit flash ROM
Additional Features	y	Support Wake-On-LAN (WOL)
	y Support Internal / External Modem Ring On

y Support USB KB/MS Wake up from S3-S5 y Includes 3 fan power connectors

y Poly fuse for keyboard over-current protection y Support STR (Suspend-To-RAM) function

y Support @BIOS™ and EasyTuneIII™

4

7ZMMC Motherboard

7ZMMC Motherboard Layout

PS/2	JP4	J3

USB1

				Socket A CPU			ATX POWER
COM A	LPT								JP6
VGA						JP10		JP8	FLOPPY
								LED1
	AUDIO&GAME	J7	J9	VT8365	DIMM1	DIMM2	JP7	IDE1
							IDE2
			JP2
			Creative	7ZMMC
			CT5880

AGP 1	SW1

CODEC

PCI1	BAT1	JP9

	JP3
PCI2	J13
J8

	JP11	VT82C	BIOS	J12
JP1		686B
J16	PCI3			J2

J17				J18
	CNR						J11
						USB2

5

		7ZMMC Motherboard Layout
			Page
	Page Index for CPU Speed Setup/Connectors/Panel and Jumper Definition
	CPU Speed Setup		P.7
	SW1		P.7
	Connectors		P.8
	ATX Power		P.8
	COM A / VGA / LPT Port		P.8
	Floppy Connector		P.9
	Game & Audio Port		P.9
	IDE 1(Primary) / IDE 2(Secondary) Connector		P.10
	J2 (System Fan)		P.10
	J3 (CPU Fan)		P.11
	J7 (AUX_IN)		P.11
	J8 (TEL)		P.12
	J9 (CD Audio Line In)		P.12
	J12 (Wake On LAN)		P.13
	J13 (Ring Power On)		P.13
	JP2 (Front Audio)		P.14
	JP6 (Power Fan)		P.14
	JP8 / LED1 (DIMM LED Connector & DIMM LED)		P.15
	PS/2 Keyboard & PS/2 Mouse Port		P.15
	USB1 (Rear USB Port)		P.16
	USB2 (Front USB Connector)		P.16
	Panel and Jumper Definition		P.17
	BAT1 (Battery)		P.17
	J11 (2x11 Pins Front Panel)		P.17
	J16/J17/J18 (CNR Select) [Optional]		P.18
	JP1 (Front MIC Function)		P.19
	JP3 (Clear CMOS Function) [Optional]		P.19
	JP4 (USB Device Wake up Selection)		P.20
	JP7 (STR Function Enable)		P.20
	JP9 (BIOS Write Protect Function)		P.21
	JP10 (CPU Clock Frequency) [Optional]		P.21
	JP11 (Onboard Sound Function Selection)		P.22

6

7ZMMC Motherboard

CPU Speed Setup

The system bus speed is selectable at 100MHz. The user can select the system bus speed by DIP switch SW1.

SW1: CPU Speed Setup

SW1:

O: ON, X: OFF

FSB

1

2

3

4

*95

O

O

X

O

100

X

O

X

X

*102

0

0

X

X

*103

X

O

X

O

*107

O

X

O

0

*110

0

X

0

X

*113

X

X

O

O

*115

X

X

X

0

*133

X

X

X

X

* These speed settings are not guaranteed.

0AMD CPU Heat Sink Installation:

Beware: Please check that the heat sink is in good contact with the CPU before you turn on your system.

The poor contact will cause over heat, and might cause damage to your processor.

7

Connectors

Connectors

ATX Power

																																												Pin No.	Definition
																																												3,5,7,13,	GND
																																							10 20					15-17
																																												1,2,11	3.3V
																																												4,6,19,20	VCC
																																												10	+12V
																																												12	-12V
																																												18	-5V
																																												8	Power Good
																																							1	11				9	5V SB stand by+5V
																																												14	PS-ON(Soft On/Off)

COM A / VGA / LPT Port

LPT Port

COM A

VGA

8

7ZMMC Motherboard

Floppy Connector

Game & Audio Port

FDD1

Red Line

Game

Port

Line Out 1

MIC In

Line In/Line Out 2

Line Out 1: Line Out or SPDIF (The SPDIF output is capable of providing digital audio to external speakers or compressed AC3 data to an external Dolby digital decoder). To enable SPDIF, simply insert SPDIF connector into Line Out1. Line Out1 will become SPDIF Out automatically. (see page 35 for more information).

To enable Four Speaker (for Creative 5880 audio only), simply follow instructions on page 32 and Line In will become Line Out2 to support second pair of stereo speakers.

9

Connectors

IDE1 (Primary), IDE2 (Secondary) Connector

IDE 2 IDE 1

	Red Line
J2: Sysem Fan
	1
Pin No.	Definition
1	Control
2	+12V
3	SENSE

10

7ZMMC Motherboard

J3: CPU Fan

																																																	1
																																										Pin No.				Definition
																																										1						Control
																																										2							+12V
																																										3					SENSE

J7: AUX_IN

1

																																				Pin No.	Definition
																																				1	AUX-L
																																				2	GND
																																				3	GND
																																				4	AUX-R

11

Connectors

J8 TEL: The connector is for Modem with internal voice connector

1

																																							Pin No.			Definition
																																							1			Signal-In
																																							2					GND
																																							3					GND
																																							4		Signal-Out

J9: CD Audio Line In

																																									1
																																								Pin No.	Definition
																																								1			CD-L
																																								2			GND
																																								3			GND
																																								4			CD-R

12

7ZMMC Motherboard

J12: Wake On LAN

1

Pin No.

Definition

1

+5V SB

2

GND

3

Signal

J13: Ring Power On (Internal Modem Card Wake Up)

																																												1
																																									Pin No.		Definition
																																									1			Signal
																																									2			GND

13

Connectors

JP2: Front Audio

		Pin No.	Definition
1	2	1	Incase speaker (R)
		2	Incase speaker (L)
		3,4,5,6,	GND
		10,15
		7	+12V
15	16	8,16	NC
		9	MIC
		11	Front Audio (R)
		13	Front Audio (L)
		12	Rear Audio (R)
		14	Rear Audio (L)

JP6: Power Fan

1

Pin No. Definition

																						1	Control
																						2	+12V
																						3	NC

14

7ZMMC Motherboard

JP8 / LED1: STR LED Connector & DIMM LED

STR LED Connector External. 1

+ DIMM LED

PS/2 Keyboard & PS/2 Mouse Port
PS/2 Mouse			PS/2
		Mouse/Keyboard
		Pin No.		Definition
6	5	1		Data
4	3	2		NC
		3		GND
2	1	4		VCC(+5V)
PS/2 Keyboard		5		Clock
		6		NC

15

Connectors

USB 1: Rear USB Port

5 6 7 8

1 2 3 4

USB 2: Front USB Connector

Pin No. Definition

1	USB V0
2	USB D0-
3	USB D0+
4	GND
5	USB V1
6	USB D1-
7	USB D1+
8	GND

																																											Pin No.	Definition
																																											1	+5V
																																				2			10				2	GND
																																											3	USB D2-
																																											4	NC
																																					1		9				5	USB D2+
																																											6	USB D3+
																																											7	NC
																																											8	USB D3-
																																											9	GND
																																											10	+5V

16

7ZMMC Motherboard

Panel And Jumper Definition

BAT1: Battery

+

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer’s instructions.

J11: 2x11 Pins Front Panel

																																		GN HD			S P K					RE	GD
																																		1						1		1	1
																																				P− P− P+						PW

17

		Panel and Jumper Definition
	GN (Green Switch)	Open: Normal Operation
		Close: Entering Green Mode
	GD (Green LED)	Pin 1: LED anode(+)
		Pin 2: LED cathode(− )
	HD (IDE Hard Disk Active LED)	Pin 1: LED anode(+)
		Pin 2: LED cathode(− )
	SPK (Speaker Connector)	Pin 1: VCC(+)
		Pin 2- Pin 3: NC
		Pin 4: Data(− )
	RE (Reset Switch)	Open: Normal Operation
		Close: Reset Hardware System
	P+P− P− (Power LED)	Pin 1: LED anode(+)
		Pin 2: LED cathode(− )
		Pin 3: LED cathode(− )
	PW (Soft Power Connector)	Open: Normal Operation
		Close: Power On/Off

J16 /J17/J18: CNR (Primary or Secondary) Select [Optional]

(CNRÆ Communication and Networking Riser)

1

																																												J16
																																	1										J17													J18
																																									1
																																													J16			J17							J18
																																			Onboard AC97										1-2		1-2						1-2
																																			CNR (Primary)										2-3		3-4						3-4
																																			Onboard AC97 CNR										1-2		1-2						1-2
																																			(Secondary)												3-4
																																			[Optional]

18

7ZMMC Motherboard

JP1: Front MIC Function

	1
Pin No.	Definition
1-2 close	Enable Front MIC
	Function
2-3 close	Disable Front MIC
	Function
JP3: Clear CMOS Function (Optional)
	1
Pin No.	Definition
1-2 close	Normal (Default)
2-3 close	Clear CMOS

19

Panel and Jumper Definition

JP4: USB Device Wake up Selection

1

Pin No.

Definition

1-2 close

Normal (Default)

2-3 close

USB Device Wake up

(If you want to use “USB Dev Wakeup from S3~S5” function, you have to set the BIOS setting “USB Dev Wakeup from S3~S5” enabled, and the jumper “JP4” enabled)

*(Power on the computer and as soon as memory counting starts, press <Del>. You will enter BIOS Setup. Select the item “POWER MANAGEMENT SETUP”, then select “USB Dev Wakeup from S3~S5”. Remember to save the setting by pressing "ESC" and choose the “SAVE & EXIT SETUP” option.)

JP7: STR Function Enable

1

Pin No.

Definition

1-2 close

STR Enable

2-3 close

Normal (Default)

20