8VM533M-RZ / 8VM533M-RZ-C
Intel® Pentium® 4 Processor Motherboard
User's Manual
Rev. 1003
12ME-VM533MRZ-1003
Copyright
© 2004GIGABYT E TECHNOLOGYCO., LT D
CopyrightbyGIGA-BYTETECHNOLOGYCO.,LTD. ("GBT"). Nopart ofthismanual may bereproduced ortransmitted inanyfrom without the expressed,written permission of GBT.
Trademarks
T hird-partybrands andnames arethepropertyof their respectiveowners.
Notice
Please do not remove anylabels on motherboard, this mayvoid the warranty of thismotherboard.
Due to rapid change in technology, some of the specifications might be out of datebefore publication of this booklet.
T he author assumes noresponsibilityfor anyerrors or omissions that mayappear in thisdocument nor does the authormake a commitmentto updatetheinformationcontained herein.
Feb.20, |
8VM533M-RZ |
MotherBoard |
2004 |
|
|
Feb.20 ,2004 |
8VM533MRZ- |
Motherboard |
Preparing Your Computer
Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To protect them against damage from static electricity, you should followsome precautions whenever you work on your computer.
1.Unplug your computer when working on the inside.
2.Use a grounded wrist strap before handling computer components. If you do not have one, touch both of your hands to a safely grounded object or to a metal object, such as the power supply case.
3.Hold components by the edges and try not touch the IC chips, leads or connectors, or other components.
4.Place components on a grounded antistatic pad or on the bag that came with the components whenever the components are separated from the system.
5.Ensure that the ATX power supply is switched off before you plug in or remove the ATX power connectoron the motherboard.
Installing the motherboard to the chassis
If the motherboard has mounting holes, butthey don't line up with the holes on the base and there are no slots to attach the spacers, do not become alarmed you can still attach the spacers to the mounting holes. Just cut the bottom portion of the spacers (the spacer maybe a little hard to cut off, so be careful of your hands). In this way you can still attach the motherboard to the base without worrying about short circuits. Sometimes you may need to use the plastic springs to isolate the screw from the motherboard PCB surface, because the circuit wire may be near by the hole. Be careful, don't let the screw contact any printed circuit write or parts on the PCB that are near the fixing hole, otherwise it maydamage the board or cause board malfunctioning.
English
Table of Contents |
|
Chapter 1 Introduction ................................................................................................ |
5 |
FeaturesSummary ........................................................................................................................... |
5 |
8VM533M-RZ Series MotherboardLayout ...................................................................................... |
6 |
Block Diagram .................................................................................................................................. |
7 |
Hardware Installation Process ......................................................................................................... |
8 |
Step 1: Install the Central Processing Unit (CPU) .......................................................................... |
8 |
Step 1-1: CPU Installation ................................................................................................. |
9 |
Step 1-2: CPU Cooling Fan Installation ............................................................................ |
9 |
Step 2: Install Memory Modules .................................................................................................... |
10 |
Step 3: Install AGP Card ............................................................................................................... |
11 |
Step 4: Install I/O Peripherals Cables ........................................................................................... |
11 |
Step 4-1: I/O Back Panel Introduction ............................................................................. |
11 |
Step 4-2: Connectors Introduction ................................................................................... |
12 |
Chapter 2 BIOS Setup ............................................................................................. |
19 |
The Main Menu (For example: BIOS Ver. : F4a) ......................................................................... |
19 |
Standard CMOS Features ............................................................................................................. |
21 |
Advanced BIOS Features ............................................................................................................. |
23 |
IntegratedPeripherals ..................................................................................................................... |
24 |
PowerManagementSetup ............................................................................................................. |
26 |
PnP/PCI Configurations ................................................................................................................. |
27 |
PC Health Status ............................................................................................................................ |
28 |
Frequency/VoltageControl ............................................................................................................. |
29 |
LoadFail-Safe Defaults ................................................................................................................... |
30 |
LoadOptimized Defaults ................................................................................................................. |
30 |
Set Supervisor/User Password ..................................................................................................... |
31 |
Save & Exit Setup ......................................................................................................................... |
32 |
Exit Without Saving ........................................................................................................................ |
32 |
Chapter 3 Install Drivers ........................................................................................... |
33 |
8VM533M -RZ Series Motherboard |
- 4 - |
Chapter 1 Introduction
Features Summary
CPU |
— Socket 478 for Intel® Pentium ® 4 (Northwood) with HT Technology |
|
|
— |
Intel® Pentium ® 4 533/400MHz FSB |
|
— 2nd cache depends on CPU |
|
|
|
|
Chipset |
— North Bridge: VIA P4M266A/P4M533 |
|
|
— South Bridge: VIA VT8235/VT8237R |
|
|
|
|
Memory |
— 2 184-pin DDR DIMM sockets, supports up to 2GB DRAM (Max) |
|
|
— |
Supports DDR266/DDR200 DIMM |
|
— Supports only 2.5V DDR SDRAM |
|
|
|
|
Slots |
— |
1 AGP slot 4X (1.5V) device support |
|
— |
3 PCI slots support 33M Hz & PCI 2.2 compliant |
|
|
|
On-Board IDE |
— 2 IDE controller provide IDE HDD/CD-ROM(IDE1, IDE2) with PIO, Bus |
|
|
|
Master (Ultra DMA33/ATA66/ATA100/ATA133) operation modes |
|
— Can connect up to 4 IDE devices |
|
|
|
|
On-Board Floppy |
— |
1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M and 2.88M bytes |
On-Board Peripherals |
— |
1 Parallel port supports Norm al/EPP/ECP mode |
|
— 1 Serial port (COMA), 1 VGA port, COMB onboard |
|
|
— 6 USB 2.0/1.1 ports (4 x Rear, 2 x Front by cable) |
|
|
— 1 Front Audio connector |
|
|
— |
1 PS/2 Keyboard |
|
— |
1 PS/2 Mouse |
|
|
|
On-Board LAN * |
— Builit-in VIA 6103 chipset * |
|
|
— |
1 RJ45 port * |
|
|
|
On-Board Sound |
— VIA VT1616 CODEC |
|
|
— |
Support 2/6 channel |
|
— |
Line Out / Line In / Mic In |
|
— |
CD In |
|
|
|
BIOS |
— Licensed AWARD BIOS |
|
|
— |
Supports Q-Flash™ |
I/O Control |
— |
ITE8705 |
Hardware M onitor |
— |
CPU Fan Revolution detect |
|
— CPU Fan Fail Warning |
|
|
— CPU tem perature detect |
|
|
— |
System Voltage Detect |
|
|
|
Additional Features |
— |
Supports @BIOS™ |
|
— |
Supports EasyTune 4™ |
Form Factor |
— |
Micro ATX size form factor, 24.5cm x 20.8cm |
"*" For 8VM533M-RZ only.
English
- 5 - |
Introduction |
English
8VM533M-RZ Series Motherboard Layout
|
|
# |
KB_MS |
|
|
COMA |
|
|
|
LPT |
|
VGA |
|
|
R_USB |
A TX_12V |
|
USB |
LAN * |
|
AUDIO |
V T6103 * |
|
|
|
|
F_AU DIO
AGP
CODEC
BIOS
I TE 8705
CD_I N
|
20.8 cm |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
CPU FAN |
|
FDD |
|
|
|
ATX |
|
|
|
|
|
|
SOC KET 478 |
|
|
||
|
|
8VM533M-RZ |
|
IDE1 |
|
|
|
IDE2 |
|
|
|
|
|
|
VIA P4M 266A /P4M 533 |
DDR2 |
|
||
|
|
DDR1 |
BAT |
|
|
PCI1 |
|
|
|
|
|
|
|
V I A V T82 35/ |
|
PCI2 |
|
V T8237R |
|
|
PCI3 |
|
|
|
|
|
F_U SB1 |
|
F_PANEL |
COMB |
|
|
||
|
|
|
|
|
PWR_LE D
24.5 cm
"*" For 8VM533M-RZ only. "#" For8VM533M-RZ-C only.
8VM533M -RZ Series Motherboard |
- 6 - |
Block Diagram
Pentium 4 |
CPUCLK+/- (100/133MHz) |
Socket 478 |
|
CPU |
|
AGP 4X
VGA Port
|
|
|
|
|
|
|
|
|
AGPCLK |
|
|
|||||
|
|
|
|
|
|
|
|
|
|
66MHz |
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3 PCI |
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
* |
|
|
|
VT6103* |
||||||||
|
|
|
|
|
|
|
|
|
RJ45 |
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
MII |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
PCIBUS 33MHz |
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
AC97 Link |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
6 Channel |
|
||||
|
|
|
|
|
|
|
|
|
|
|
CODEC |
|
||||
PCICLK |
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|||||
(33MHz) |
|
|
|
|
|
|
MIC LINE-IN |
LINE-OUT |
||||||||
|
|
|
|
|
|
|
|
|
|
|
||||||
System Bus |
200/266MHz |
533/400MHz |
VIA
P4M266A/P4M533
66MHz V_Link
DDR
MCHCLK (100/133MHz)
AGPCLK66 MHz
33 MHz
48 MHz |
14.318 MHz |
|
|
|
BIOS |
|
|
|
|
|
|
VIA |
|
|
|
LPCBUS |
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
VT8235/VT8237R |
|
|
|
|
|
|
Floppy |
|
||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IT8705 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
LPT Port |
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
24 MHz |
PS/2 KB/Mouse |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
33 MHz |
|
|
|
|
|
|
|
|
||
|
|
6 USB |
|
|
|
|
ATA33/66/ |
COM A/COMB |
||||||||||||||||||
|
|
|
|
|
|
|
|
|
||||||||||||||||||
|
|
|
Ports |
|
|
|
|
100/133 |
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
IDE Channels |
|
|
|
|
|
|
|
|
|
|
|
|||||||
PCICLK (33MHz) |
|
CLK |
|
MCHCLK (100/133MHz) |
|
|
|
||||
USBCLK (48MHz) |
|
|
CPUCLK+/- (100/133MHz) |
||
|
|
|
|
||
14.318 MHz |
|
GEN |
|
AGPCLK (66MHz) |
|
|
|
||||
33 MHz |
|
|
|
|
V_Link (66MHz) |
|
|
|
|
|
|
"*" For 8VM533M-RZ only.
English
- 7 - |
Introduction |
English
Hardware Installation Process
To set up your computer, you must complete the following steps:
Step 1- Install the Central Processing Unit (CPU)
Step 2- Install mem ory modules
Step 3- Install expansion cards
Step 4- Connect ribbon cables, cabinet wires, and power supply
Step 4 |
Step 1 |
Step 2 |
Step 4
Step 4
Step 3
Step 1: Install the Central Processing Unit (CPU)
Before installing the processor, adhere to the following warning:
1. |
Please m ake sure the CPU type is supported by the m otherboard. |
2. |
The processor will overheat without the heatsink and/or fan, resulting in perm anent |
|
irreparable damage. |
3. |
If you do not match the CPU socket Pin 1 and CPU cut edge well, it will cause im proper |
installation. Please change the insert orientation.
4. Apply thermal grease between the processor and cooling fan.
5. Never run the processor without the heatsink properly and firmly attached. Perm anent damage will result.
6. Please set the CPU host frequency in accordance with your processor's specifications. We don't recomm end you to set the system bus frequency over the CPU's specification because these specific bus frequencies are not the standard specifications for CPU, chipset and most of the peripherals. Whether your system can run under these specific bus frequencies properly will depend on your hardware configurations, including CPU, Memory, Cards… etc.
HT functionality requirement content :
Enabling the functionality of Hyper-Threading Technology for your com puter system requires all of the following platform components:
-CPU: An Intel® Pentium 4 Processor with HT Technology
-Chipset: An VIA Chipset that supports HT Technology
- BIOS: A BIOS that supports HT Technology and has it enabled
- OS: An operation system that has optim izations for HT Technology
8VM533M -RZ Series Motherboard |
- 8 - |
Step 1-1: CPU Installation
Socket
Actuation
Lever
Figure 1.
Pull the rod to the 90-degree directly.
Figure 2.
Locate Pin 1 in the socket and look for a (golden) cut edge on the CPU upper corner. Insert the CPU into the socket. (Do not force the CPU into the socket.) Then m ove the socket lever to the locked position while holding pressure on the center of the CPU.
Step 1-2: CPU Cooling Fan Installation
Figure 1.
Apply the therm al tape(or grease) to provide better heat conduction between your CPU and cooling fan.
Figure 2.
Fasten the cooling fan supporting-base onto the CPU socket on the motherboard.
Figure 3.
Make sure the CPU fan is plugged to the CPU fan connector, than install complete.
English
- 9 - |
Hardware Installation Process |
English
Step 2: Install Memory Modules
Before installing the m emory modules, adhere to the following warning:
1. Please note that the DIMM module can only fit in one direction due to the one notch. Wrong orientation will cause im proper installation. Please change the insert orientation.
The motherboard has 2 dual inline memory m odule (DIM M) sockets. The BIOS will automatically detects memory type and size. To install the memory module, just push it vertically into the DIMM socket. The DIM M module can only fit in one direction due to the notch. M emory size can vary between sockets.
Notch
DDR
1. The DIMM socket has a notch, so the DIMM memory module can only fit in one direction.
2. Insert the DIMM mem ory module vertically into the DIM M socket. Then push it down.
3. Close the plastic clip at both edges of the DIMM sockets to lock the DIM M m odule.
Reverse the installation steps when you wish to rem ove the DIM M module.
8VM533M -RZ Series Motherboard |
- 10 - |
Step 3: Install AGP Card
1 |
. Read the relateAGP card's instruction document before install the AGP card into the computer. |
2 |
. If your AGP card has "AGP 4X(1.5V) notch" (show below), please make sure your AGP card is AGP |
|
4X(1.5V). |
3. Please carefully pull out the small whitedrawable bar at the end of the AGP slot when you try to install/ Uninstall the AGP card. Please align the AGP card to the onboard AGP slot and press firm ly down on the slot .M ake sure your AGP card is locked by the sm all whitedrawable bar.
Step 4: Install I/O Peripherals Cables
Step 4-1: I/O Back Panel Introduction
u |
v |
|
z * |
|
|
| |
|
|
w |
x y |
} |
|
|
|
{ |
|
|
|
~ |
uPS/2 Keyboard and PS/2 Mouse connector
This connector supports standard PS/2 keyboard and PS/2 m ouse.
vParallel port (LPT)
Device like printer can be connected to Parallel port.
wSerial port (COMA)
Mouse and modem etc. can be connected to Serial port.
xVGA port
Monitor can be connected to VGA port. y/{ USB port
Before you connect your device(s) into USB connector(s), please make sure your device(s) such as USB keyboard, mouse, scanner, zip, speaker...etc. Have a standard USB interface. Also m ake sure your OS supports USB controller. If your OS does not support USB controller, please contact OS vendor for possible patch or driver upgrade. For more information please contact your OS or device(s) vendors.
"*" For 8VM533M-RZ only.
English
- 11 - |
Hardware Installation Process |
Loading...