4.12. USER PASSWORD...........................................................................................4-27
4.13. IDE HDD AUTO DETECTION...........................................................................4-28
4.14. SAVE & EXIT SETUP........................................................................................4-29
4.15. EXIT WITHOUT SAVING..................................................................................4-30
22
Page 3
6EA
1.INTRODUCTION
1.1. PREFACE
Welcome to use the 6EA motherboard. It is a Pentium II Processor based
PC / AT compatible system with AGP / PCI / ISA Bus, and has been designed to
be the fastest PC / AT system. There are some new features allow you to
operate the system with just the performance you want.
This manual also explains how to install the motherboard for operation, and
how to set up your CMOS CONFIGURATION with BIOS SETUP program.
q Supports 2xDIMMs using 3.3V EDO or SDRAM DIMM module.
q Supports 8MB ~ 256 MB SDRAM memory on board.
q Supports ECC or Non-ECC type DRAM module.
q 1xAGP slot, 3xPCI Bus slots, 2xISA Bus slots.
q Supports 2 channels Ultra DMA/33 IDE ports for 4 IDE Devices.
q Supports 2xCOM (16550), 1xLPT (EPP / ECP), 1x1.44MB Floppy port.
q Supports USB port & PS/2 Mouse port.
q Licensed AWARD BIOS, 2M bits FLASH RAM.
q 22 cm x 25 cm Baby AT SIZE form factor, 4 layers PCB.
1-1
Page 4
Introduction
1.3. PERFORMANCE LIST
The following performance data list is the testing results of some popular
benchmark testing programs.
These data are just referred by users, and there is no responsibility for different
testing data values gotten by users. (The different Hardware & Software
configuration will result in different benchmark testing results.)
• CPU
• DRAM(32x 2) MB SDRAM (LGS GM72V661641CT7J)
• CACHE SIZE512 KB included in CPU
• DISPLAYGA-601 AGP Display Card (4MB SGRAM)
• STORAGEOnboard IDE (Seagate ST36530A)
• O.S.Windows NT™ 4.0
• DRIVERDisplay Driver at 1024 x 768 x 64K colors x 75Hz.
Processor
Pentium II processor
TRIONES Bus Master IDE Driver 3.70
Intel Pentium II
266MHz(66x4)333MHz(66x5)
Winbench98
CPU mark32721864
FPU Winmark13801720
Business Disk21002140
Hi-End Disk52605420
Business Graphics159183
Hi-End Graphics167195
Winstone98
Business29.432.8
Hi-End31.635
1-2
Page 5
6EA
DIMM Sockets
SLOT
SLOT 1
1.4. BLOCK DIAGRAM
AGP
AGP Bus
66MHz
Ultra DMA/33
IDE Ports
PCI Bus
IDE Bus
ISA Bus
66MHz
Host Bus
PAC
82443EX
CHIPSET
PIIX4
82371EB
CHIPSET
DRAM Bus
33MHz
33MHz
33MHz
48MHz
14.318MHz
USB Bus
14.318MHz
3.3V EDO/SDRAM
66MHz
PLL
52C64-05
I/O
CHIPSET
ITE8671F
14.318MHz
24MHz
USB Ports
COM Ports
LPT Port
Floppy Port
1-3
Keyboard
PS/2 Mouse
Page 6
1.5. INTRODUCE THE Pentium II Processor
Figure 1:Retention Mechanism & attach Mount
Introduction
Figure 2:OEM Pentium II Processor
1-4
Page 7
6EA
Figure 3:Heatsink / FAN & Heat sink support for OEM Pentium II Processor
Figure 4:Boxed Pentium II Processor & Heat sink support
1-5
Page 8
Introduction
1.6 What is AGP
?
The Accelerated Graphics Port (AGP) is a new port on the Host-To-PCI bridge
device that supports an AGP port. The main purpose of the AGP port is to
provide fast access to system memory.
The AGP port can be used either as fast PCI port (32-bits at 66MHz vs. 32-bits
at 33MHz) or as an AGP port which supports 2x data-rate, a read queue, and
side band addressing. When the 2x-data rate is used the port can transmit data
at 533MB/sec (66.6*2*4). The read-queue can be used to pipeline reads –
removing the effects of the reads-latency. Side band addressing can be used to
transmit the data address on a separate line in order to speed up the
transaction.
• Electricity− 4.9 V to 5.2 V. (Max. 20A current at 5V.)
2-2
Page 11
6EA
3.HARDWARE INSTALLATION
3.1. UNPACKING
The mainboard package should contain the following:
•The 6EA main board.
•The Retention Mechanism & Attach Mount
•USER'S MANUAL for main board.
•Cable set for IDE, Floppy & I/O devices.
•CD for main board Utility. (Bus Master IDE Driver, Suspend to HD Utility,
LDCM, SIV, Patch 95)
The main board contains sensitive electric components, which can be easily
damaged by static electricity, so the main board should be left in its original
packing until it is installed.
Unpacking and installation should be done on a grounded anti-static mat. The
operator should be wearing an anti static wristband, grounded at the same
point as the anti-static mat.
Inspect the main board carton for obvious damage. Shipping and handling
may cause damage to your board. Be sure there are no shipping and handling
damages on the board before proceeding.
After opening the main board carton, extract the system board and place it only
on a grounded anti-static surface component side up. Again inspect the board
for damage. Press down on all of the socket IC's to make sure that they are
properly seated. Do this only on with the board placed on a firm flat surface.
M
DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED.
3-1
Page 12
3.2. MAINBOARD LAYOUT
JP2
JP3
IDE 1
IDE 2
PWR
TD
TB
GN
HD
SOFT
Hardware Installation
ISA 2
ISA 1
PCI 3
PCI 2
PCI 1
COM A
LPT
USB
PS2
COM B
KB
JP1
WAKE
ON
LANE
BAT1
SW
FAN
PWR
FLOPPY
ATX POWER
POWER
BIOS
JP4
BANK 1
BANK 0
1
J10
SB-LINK
PIIX4E
6EA
AGP
Intel 440EX
82443LX
CPU
×Figure 3.1Ø
3.3. QUICK REFERENCE FOR JUMPERS & CONNECTORS
t I/O Ports Connector
USBUSB port.
IDE1For Primary IDE port.
IDE2For Secondary IDE port.
KBFor Keyboard port.
PS/2For PS/2 Mouse port.
FLOPPYFor Floppy port
COMBFor Serial port2 (COM B).
COMAFor Serial port1 (COM A).
LPTFor LPT port.
t Slot 1
For Pentium II Processor installed
3-2
Page 13
6EA
t IR : INFRARED Connector (IR) -- Function Option
Pin No.Function
1IR Data Output
2GND
3IR Data Input
4Signal
5POWER (+)
t PWR : POWER ON LED ( PW-LED)
Pin No.Function
1LED POWER (+)
2LED POWER (-)
3LED POWER (-)
t SPK : SPEAKER Connector
Pin No.Function
1VCC
2NC.
3NC.
4Signal
t TD : Turbo LED Connector
Pin No.Function
1LED POWER (+)
2LED POWER (-)
t RST : RESET Switch
Pin No.Function
1RESET Input
2GND
t GN : GN-SW
Pin No.Function
1CTRL-Signal
2GND
t HD : Hard Disk active LED (HD-LED)
Pin No.Function
1LED POWER (+)
2LED POWER (-)
3-3
Page 14
t Soft PWR : Soft Power Switch
Pin No.Function
1CTRL-Signal
2GND
t FAN PWR : CPU cooling FAN Power Connector
Pin No.Function
1GND.
2+12V
3SENSE
t J10 : System After Ac Back
Pin No.Function
1-2 OpenSoft Off.
1-2 CloseFull On.
t JP1 : Keyboard Power On Selection
Pin No.Function
1-2Enabled Keyboard power on.
2-3Disabled Keyboard power on.
t Wake on Lan
Pin No.Function
1+5V SB
2GND
3Signal
Hardware Installation
t SB-LINK : For PCI Audio / Sound Card use only
Pin No.Function
1Signal
2GND
3NC
4Signal
5GND
6Signal
3-4
Page 15
6EA
3.4. DRAM INSTALLATION
The main board can be installed with 8 / 16 / 32 / 64 / 128 / 256 MB 168 pins
DIMM module DRAM, and the DRAM speed must be 50 or 60 ns for EDO &
67MHz for SDRAM when system bus speed is set to 66MHz. The DRAM
memory system on main board consists of bank 0 and bank 1 .
Since 168 pins DIMM module is 64 bits width, therefore 1 piece of DIMM
module may match a 64 bits system. The total memory size is 8 MB ~ 256MB
SDRAM. The DRAM installation position refer to Figure 3.1, and notice the Pin
1 of DIMM module must match with the Pin 1 of DIMM socket. Insert the DRAM
DIMM module into the DIMM socket at Vertical angle. If there is a wrong
direction of Pin 1, the DRAM DIMM module could not be inserted into socket
completely.
3.5. CPU SPEED SETUP
The system bus speed can be set to 66.6MHz form the jumper (JP2,JP3,JP4).
The user can change the DIP SWITCH (SW) selection to set up the CPU speed
for different processors. The CPU speed must match with the frequency
RATIO and Front Side Bus (FSB) speed. It will cause system hanging up if the
frequency RATIO and FSB Speed do not match with the CPU.
3-5
Page 16
Hardware Installation
DIP SWITCH (SW)
1234
OFFOFFONON3.566233Pentium
ONONOFFON466266Pentium
OFFONOFFON4.566300Pentium
ONOFFOFFON566333Pentium
OFFOFFOFFON5.566366Pentium
FREQ.
RATIO
EXT.CLK.
MHz
INT.CLK.
MHz
CPU Type
II 233 MHz
II 266 MHz
II 300 MHz
II 333 MHz
II 366 MHz
MAIN CLOCKJP2JP3JP4
66MHz
75MHz
83MHz
M
The CPU is a sensitive electric component and it can be easily
damaged by static electricity, so users must keep it away from metal
surface when the CPU is installed onto main board.
1-21-21-2
1-22-31-2
2-32-32-3
3.6. CMOS RTC & ISA CFG CMOS SRAM
There're RTC & CMOS SRAM on board; they have a power supply from
external battery to keep the DATA inviolate & effective. The RTC is a REALTIME CLOCK device, which provides the DATE & TIME to system. The CMOS
SRAM is used for keeping the information of system configuration, so the
system can automatically boot OS every time. Since the lifetime of internal
battery is 5 years, the user can change a new Battery to replace old one after it
cannot work.
M Danger of explosion if battery is incorrectly replaced.
M Replace only with the same or equivalent type recommended by the
manufacturer.
M Dispose of used batteries according to the manufacturer’ s instructions.
3-6
Page 17
6EA
3.7. SPEAKER CONNECTOR INSTALLATION
There is a speaker in AT system for sound purpose. The 4 - Pins connector
SPK is used to connect speaker.
3.8. HARDWARE RESET SWITCH CONNECTOR INSTALLATION
The RESET switch on panel provides users with HARDWARE RESET function.
The system will do a cold start after the RESET switch is pushed and released
by user. The RESET switch is a 2 PIN connector and should be installed to
RST on main board.
3.9. POWER LED CONNECTOR INSTALLATION
System has power LED lamp on the panel of case. The power LED will light on
off or flash to indicate which step on the system. The connector should be
connected to PWR of main board in a correct direction.
3.10. IDE & ATAPI DEVICE INSTALLATION
There are two-Enhanced PCI IDE ports (IDE1, IDE2) on board, which following
ATAPI standard SPEC. Any one IDE port can connected to two ATAPI devices
(IDE Hard Disk, CD-ROM & Tape Driver), so total four ATAPI devices can exist
in a system. The HD is the active LED port for ATAPI devices.
3.11. PERIPHERAL DEVICE INSTALLATION
After the I/O device installation and jumpers setup, the mainboard can be
mounted into the case and fixed by screw. To complete the mainboard
installation, the peripheral device could be installed now. The basic system
needs a display interface card. If the PCI - Bus device is to be installed in the
system, any one of four PCI - Bus slots can be used.
3.12. KEYBOARD & PS/2 MOUSE INSTALLATION
The main board supports PS/2 Mouse (J7). The BIOS will auto detect whether
the PS/2 Mouse is installed or not & assign IRQ12 for PS/2 Mouse port if it is
installed. After installing the peripheral device, the user should check
everything again, and prepare to power-on the system.
3-7
Page 18
Page 19
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.